應用於數位電視頻帶之平衡不平衡轉換器設計

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：44

、訪客IP：52.15.223.239

姓名

呂鎮安(Jen-an Lyu) 查詢紙本館藏

畢業系所

電機工程學系

論文名稱

應用於數位電視頻帶之平衡不平衡轉換器設計
(Balun Design for Digital TV(DVB-T))

相關論文

★ 利用缺陷型接地結構之雙頻微型平面倒F天線設計	★ 應用於第三代行動電話之倒Ｆ天線設計
★ 使用寄生元件之平面式倒F型雙頻天線設計	★ 利用寄生元件之平面式倒 F 型三頻天線設計
★ 無線通訊之三頻天線設計	★ 無線通訊之雙頻與三頻槽孔型天線設計
★ 應用於智慧型行動裝置之LTE/WWAN多頻單極天線設計	★ 應用於行動手持裝置之LTE/WWAN天線設計
★ 利用背腔式槽孔線結構之多頻段天線設計	★ 利用缺陷地面共振電路之介質量測技術
★ 應用於藍芽與全球衛星定位系統之電抗性負載型雙頻槽孔天線	★ 帶通圓形極化頻率選擇面之設計
★ 啞鈴型缺陷地面之介質量測電路分析與設計	★ 雙頻圓極化微波極化器設計
★ 利用微小共振電路之多頻段天線設計	★ 應用於X-band平面吸波器之薄型負載電路設計

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本論文介紹應用於數位電視頻帶(UHF 470-710 MHz)之平衡-不平衡轉換器(Balun)。因應數位電視分佈於較低頻帶的需求，傳統馬群(Marchand)平衡-不平衡轉換器因為其四分之波長耦合線，有電路面積過大的問題。本論文提出利用傳統馬群平衡-不平衡轉換器架構，將原本電路結構之開路端變成短路端，使耦合線長度由縮短成，應用於較低輸出阻抗轉換時，仍能得到良好之電氣響應。同時利用一個於開路端聯接到地的電容器，找出開路與短路架構兩者之間控制頻寬的機制，則在本文中也有詳細的探討。在之後章節裡進一步提出微小化，並適用於窄頻操作，且達成各種實數輸出阻抗轉換之平衡-不平衡轉換器，但其對輸出阻抗的改變是較為敏感的。引入阻抗中心並以放大器設計觀點為例，提出能在一段實數輸出阻抗範圍下，中心頻率皆不隨之飄移之電路架構，且頻寬具有可調性，耦合線長度更可縮短至。最終，提出符合單面電路板的佈局方法，可做為實現全平面電路的另外一種選擇。本論文設計之平衡-不平衡轉換器，其平衡端大小差皆在0.5dB，相位差皆在5度之內。所有的量測與模擬結果皆在FR4基板上實現，均有良好的一致性。

摘要(英)

Baluns designed for digital TV( UHF 470-710MHz ) applications will be presented in this thesis. Conventional Marchand baluns employ coupled lines. These structures occupy large circuit areas, especially for lower frequency applications (ex .DVB-T). In this thesis, we replaced conventional Marchand baluns open-terminal to short, the required coupled-line lengths of this balun structure can be made as short as . This balun is suitable for low impedance-transforming ratio . At open-terminal, with a series capacitor to ground, we can find how to control bandwidth by using the optimal value of the capacitor. The miniature, narrow band, wide impedance-transforming ratio balun is realized by using one series capacitor at unbalanced port, but it is sensitive to output impedance. In terms of the center of impedance and amplifier design, circuit structures insensitive to output impedance are presented. This balun bandwidth is controllable, and the required coupled-line lengths of this balun structure can be made as short as . Finally, the fabrication on single printed circuit broad is presented, and it supplied another choice. Both baluns achieved 0.5 dB amplitude balance and phase balance. All circuits are fabricated on FR4 substrate, and are in good agreement with simulation.

關鍵字(中)

★ 阻抗轉換
★ 分散式
★ 集總式
★ 平衡不平衡轉換器
★ 微小化

關鍵字(英)

★ miniature
★ baluns
★ impedance transformation
★ lumped. distributed

論文目次

中文摘要 ………………………………………………… Ⅰ
英文摘要 ………………………………………………… Ⅱ
誌謝 ………………………………………………… Ⅲ
目錄 ………………………………………………… Ⅳ
圖目錄 ………………………………………………… Ⅶ
表目錄 ………………………………………………… XI
第一章序論…………………………………………… 1
第二章微小型平衡-不平衡轉換器………………….. 3
2-1 序論…………………………………………… 3
2-2 馬群平衡不平衡轉換器計…………………… 4
2-2-1 馬群平衡-不平衡轉換器簡介……………….. 4
2-2-2 耦合線奇模態和偶模態之介紹……………… 5
2-2-3 馬群平衡-不平衡轉換器之設計流程……….. 6
2-2-4 模擬與量測比較……………………………… 15
2-3 頻寬調整的機制……………………………… 17
2-3-1 動機與簡介…………………………………… 17
2-3-2 模擬分析與比較……………………………… 17
2-4 微小型平衡-不平衡轉換器…………………... 26
2-4-1 動機與簡介…………………………………… 26
2-4-2 微小型平衡-不平衡轉換器設計流程……….. 27
第三章對阻抗不敏感微小型平衡-不平衡轉換器….. 33
3-1 序論…………………………………………… 33
3-2 適用於各種阻抗轉換的平衡-不平衡轉換器… 35
3-2-1 動機與簡介……………………………………. 35
3-2-2 設計概念與方法………………………………. 36
3-2-3 對輸出阻抗敏感度之探討……………………. 45
3-3 對阻抗不敏感微小型平衡-不平衡轉換器…… 51
3-3-1 簡介與動機……………………………………. 51
3-3-2 設計概念與方法………………………………. 54
3-3-3 頻寬的可調性…………………………………. 59
3-3-4 模擬與量測比較………………………………. 66
3-4 運用單面板製程實現…………………………. 69
3-4-1 動機及簡介……………………………………. 69
3-4-2 單面板製程設計流程…………………………. 69
3-5 整理分析與比較………………………………. 72
第四章結論……………………………………………. 75
參考文獻 …………………………………………………. 77

參考文獻

[1] N. Marchand, “Transmission-line conversion transformers,” Electronics,vol. 17, no. 12, pp. 142–145, 1944.
[2] R. Sturdivant, “Balun designs for wireless, mixers amplifiers and antennas,”Appl. Microwaves, vol. 5, pp. 34–44, Summer 1993.
[3] D. Raicu, “Design of planar, single-layer microwave baluns,” in IEEE MTT-S Int. Microwave Symp. Dig., 1998, pp. 801–804.
[4] A. M. Pavio and A. Kikel, “A monolithic or hybrid broadband compensated balun,” in IEEE MTT-S Int. Microwave Symp. Dig., 1990, pp.483–486.
[5] K. Nishikawa, I. Toyoda, and T. Tokumitsu, “Compact and broad-band three-dimensional MMIC balun,” IEEE Trans. Microwave Theory Tech.,vol. 47, pp. 96–98, Jan. 1999.
[6] R. H. Jansen, J. Jotzo, and M. Engels, “Improved compaction of multilayer MMIC/MCM baluns using lumped element compensation,” in IEEE MTT-S Int. Microwave Symp. Dig., 1997, pp. 401–404.
[7] Y. J. Yoon, Y. Lu, R. C. Frye, M. Y. Lau, P. R. Smith, L. Ahlquist, and D. P. Kossives, “Design and characterization of multilayer spiral transmission line baluns,” IEEE Trans. Microwave Theory Tech., vol. 47, pp.
1841–1847, Sept. 1999.
[8] C. W. Tang and C. Y. Chang, “A semi-lumped balun fabricated by low temperature co-fired ceramic,” in IEEE MTT-S Int. Microw. Symp. Dig.,2002, pp. 2201–2204.
[9] H. K. Chiou, H. H. Lin, and C. Y. Chang, “Lumped-element compensated high/low-pass balun design for MMIC double-balanced mixer,”IEEE Microwave Guided Wave Lett., vol. 7, pp. 248–250, Aug. 1997.
[10] D.W. Lew, J. S. Park, D. Ahn, N. K. Kang, C. S. Yoo, and J. B. Lim, “A design of ceramic chip balun using the multilayer configuration,” IEEE Trans. Microwave Theory Tech., vol. 49, pp. 220–224, Jan. 2001.
[11] S. P. Ojha, G. R. Branner, and B. P. Kumar, “A miniaturized lumpeddistributed balun for modern wireless communication systems,” in Proc.IEEE Midwest Circuits and Systems Symp., vol. 3, 1996, pp. 1347–1350.
[12] B. P. Kumar, G. R. Branner, and B. Huang, “Parametric analysis of improved planar balun circuits for wireless microwave and RF applications,”in Proc. IEEE Midwest Circuits and Systems Symp., 1998, pp.474–475.
[13] C. W. Tang and C. Y. Chang, “A semi-lumped balun fabricated by low temperature co-fired ceramic,” in IEEE MTT-S Int. Microwave Symp.Dig., 2002, pp. 2201–2204.
[14] Y. C. Leong, K. S. Ang, and C. H. Lee, “A derivation of a class of 3-port baluns from symmetrical 4-port networks,” in IEEE MTT-S Int.Microwave Symp. Dig., 2002, pp. 1165–1168.
[15] S. C. Tseng, C. H. Wu, C. K, Huang , “Monolithic broadband Gilbert micromixer with an integrated Marchand balun using standard silicon IC process,” IEEE Trans. Microwave Theory Tech., vol. 54, pp. 4362–4371,Dec.2006.
[16] S. A. Maas and K. W. Chang, “A broadband planar, doubly balanced monolithic Ka-band diode mixer,” IEEE Trans. Microwave Theory Tech., vol. 41, pp. 2330–2335, Dec. 1993.
[17] D. M. Pozar, Microwave Engineering, 2nd edition. New York: Wiley, 1998.
[18] Jia-Sheng Hong and M. J. Lancaster, Microstrip Filters for RF/Microwave Applications. New York: Wiley, 2001.
[19] HFSS. Ansoft Corporation, Pittsburgh, PA, 2001.
[20] Microwave Office. Appl. Wave Res. Inc., El Segundo, CA, 2002.
[21] ADS version 2003A, Agilent Inc., 2003.
[22] 林祐生，微波濾波器設計課程講義，95年

指導教授

丘增杰、郭明庭
(Tsen-chieh Chiu、David M. T. Kuo)

審核日期

2007-7-6

推文