![]() |
|
以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數:46 、訪客IP:3.15.21.48
姓名 楊竣傑(Chun-Jay Yang) 查詢紙本館藏 畢業系所 機械工程學系 論文名稱 氫能利用:過焓觸媒熱電產生器之實作研究
(Hydrogen Usage: An Experimental Study of An Excess Enthalpy, Catalytic, Thermoelectric Generator)相關論文 檔案 [Endnote RIS 格式]
[Bibtex 格式]
[相關文章]
[文章引用]
[完整記錄]
[館藏目錄]
[檢視]
[下載]
- 本電子論文使用權限為同意立即開放。
- 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
- 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
摘要(中) 本研究應用熱再循環原理與觸媒燃燒技術,發展一過焓觸媒燃燒器。主要設計概念是以蜂巢式白金觸媒作為燃燒室主體,利用氫氣不需加熱便可與觸媒反應之特性,解決燃燒器的引燃問題,而且使氫燃料在極貧油的情況下仍可穩定進行反應,使燃料利用更有效率。實驗重點針對預混氫氣/空氣燃料於白金蜂巢式觸媒表面催化後所產生之熱流場作研究,使用熱電偶溫度量測系統獲得瑞士捲燃燒器溫度分佈,主要是在瑞士捲燃燒器入口、出口、觸媒段入口與出口處等,將熱電偶埋入至瑞士捲燃燒器流道中,藉由改變燃氣雷諾數(Ref)、當量比(?)及觸媒段長度(Lc)等實驗參數探討其對燃燒器溫度分佈變化之影響,本實驗有助於建立觸媒燃燒與熱再循環之整合技術。同時針對觸媒材料使用之限制,我們定義出此燃燒器最佳化操作區域,以充分掌握燃燒器關鍵操作技術。過焓觸媒燃燒器之實驗結果顯示,氫氣與空氣混合體積濃度比Cvp = 0.27%時仍可穩定產生熱釋放,大幅地延伸傳統貧油可燃極限(氫氣的貧油可燃極限為Cvp = 4%)。有關燃氣雷諾數和停滯時間對觸媒段出口溫度Tc-out之影響如下,在Lc = 3.0 cm與固定?值條件下和Ref ? 380 ~ 630的範圍內,Tc-out將隨 Ref增加而上升,這可能是因為氫氣在觸媒表面擁有極佳的吸附能力和解離能力,在很短的停滯時間內便可以啟動觸媒燃燒反應,所以停滯時間效應對觸媒段出口溫度影響並不明顯。至於燃燒器應用方面,我們串聯多個熱電材料(Bi2Te3)元件,以建構一簡易熱電產生器。初步實驗結果顯示,串聯2個熱電元件可產生約5.2伏特無負載電壓,可輕易讓低功率燈泡發亮和驅動馬達,但目前輸出電壓的穩定度仍然不佳,我們將繼續提升系統穩定度,以邁向最佳化設計。 摘要(英) This study applies heat recirculation and catalytic combustion technologies to develop an excess enthalpy catalytic burner. We use honeycomb Pt catalyst as the main body of the combustor, so that hydrogen gas can react with Pt catalyst even at room temperature without extra ignition energy. This avoids several ignition problems and makes the use of fuel more efficient. Many K-type thermocouples are inserted into the channels of the Swiss-roll burner to measure the temperature distributions at various different experimental parameters, such as the flow Reynolds number (Ref = VfD/?) ranging from 380 to 630, fuel/air mixture by volume (Cvp) ranging from 0.27% to 8% and the length of the honeycomb catalyst (Lc) ranging from 0.5 cm to 3.0 cm, where Vf is the gas velocity, D is the width of the channel, and ? is the kinematic viscosity of reactants. From these temperature measurements, the integration of heat recirculation and catalytic combustion technologies can be achieved. The optimum operating region in using the Swiss-roll catalytic burner is identified. The results indicate that our burner can be operated at extra lean condition with only Cvp = 0.27%, which is much less than the common lean flammability limit of H2/air mixtures (Cvp = 4%). The effect of Ref on Tc-out (outside temperature of the honeycomb catalyst) at fixed Cvp and Lc = 3.0 cm is discussed. For the practical use, we apply Bismuth Telluride thermoelectric (TE) chips in series to construct a small TE power generator, where the TE materials are purchased from Hi-Z technology company with model HZ-2 (~3 cm x 3 cm area). The preliminary results show that the Swiss-roll catalytic TE generator can easily produce about 0.46 watts if only two TE chips in series are used. Areas for future study and further improvement are discussed, such as the stability of the power output and the optimal operating conditions. 關鍵字(中) ★ 熱再循環
★ 觸媒燃燒
★ 熱電材料關鍵字(英) ★ catalytic combustion
★ thermoelectric materials
★ heat recirculation論文目次 目 錄
摘要…………………………………………………………………........I
英文摘要………………………………………………………………...II
誌謝……………………………………………………………………..III
目錄……………………………………………………………………..IV
圖表目錄................................................................................................VII
符號說明………………………………………………………………...X
第一章 前言……………………………………………………………..1
1.1 研究動機……………………………………………………….1
1.2 問題所在……………………………………………………….2
1.3 解決方案……………………………………………………….3
1.4 論文概要……………………………………………………….4
第二章 文獻回顧………………………………………………………..6
2.1 熱再循環燃燒原理與應用…………………………………….6
2.2 觸媒反應原理與觸媒燃燒技術之應用……………………….9
2.3 熱電材料之發展……………………………………………...11
第三章 實驗設備與實驗方法…………………………………………19
3.1 瑞士捲觸媒燃燒器設備……………………………………...19
3.1.1 瑞士捲燃燒器之製作…………………………………19
3.1.2 實驗觸媒材料…………………………………………20
3.2 燃氣供應系統………………………………………………...20
3.2.1實驗氣體與流量控制混合裝置……………………….20
3.2.2預混燃氣操作方式與相關計算……………………….21
3.3 量測儀器系統………………………………………………...23
3.3.1 溫度量測系統…………………………………………23
3.3.2 電壓及電流輸出量測系統……………………………23
3.4 過焓觸媒熱電產生器………………………………………...24
3.4.1 熱電材料………………………………………………24
3.4.2 熱電產生器之設計……………………………………24
3.5 實驗流程……………………………………………………...25
第四章 結果與討論................................................................................35
4.1 觸媒燃燒器之特性分析……………………………………...35
4.1.1溫度分佈量測與觸媒反應特徵……………………….35
4.1.2觸媒段出口溫度與燃氣雷諾數效應………………….38
4.1.3貧油可燃極限之量測………………………………….39
4.1.4 觸媒燃燒室設計溫度分佈與性能分析………………39
?? 4.1.5 燃燒器上板溫度分佈量測……………………………41
4.2 熱再循環熱電產生器之性能分析…………………………...42
4.2.1實驗初步結果分析…………………………………….42
4.2.2系統特性歸納………………………………………….43
第五章 結論與未來工作………………………………………………57
5.1 結論…………………………………………………………...57
5.2 未來工作……………………………………………………...58
參考文獻………………………………………………………………..59參考文獻 Chao, Y. C., and Chen, G. B., “Ignition hysteresis of hydrogen-air mixture in a platinum monolith honeycomb reactor”, The Third Asia-Pacific Conference on Combustion, June 24-27, Seoul, Korea, pp. 207-210 (2001).
Fernandez-Pello, A. C., “Micro-power generation using combustion: issues and approaches”, Proc. Combust. Inst., Vol. 29, pp. 883-899 (2002).
Fernandes, N. E., Park, Y. K., and Vlachos, D. G., “The autothermal behavior of platinum catalyzed hydrogen oxidation: experiments and modeling”, Combust. Flame, Vol. 118, pp. 164-178, (1999).
Jugjai, S., and Rungsimuntuchart, N., “High efficiency heat-recirculating domestic gas burners”, Exp. Thermal Fluid Sci., Vol. 26, pp. 581-592 (2002).
Kuper, W. J., Blaauw, M., Berg, F., and Graaf, G. H., “Catalytic combustion concept for gas turbines”, Catal. Today, Vol. 47, pp. 377-389 (1999).
Nolas, G. S., Sharp, J., and Goldsmid, H. J., Thermoelectrics-Basic Principles and New Materials Developments, 1st ed., Springer, Berlin (2001).
Riffat, S. B., and Ma, X., “Thermoelectrics: a review of present and potential applications”, Applied Thermal Engineering, Vol. 23, pp. 913-935 (2003).
Rowe, D. M., “Thermoelectrics, an environmentally-friendly source of electrical power”, Renewable Energy, Vol. 16, pp. 1251-1256 (1999).
Rowe, D. M., CRC Handbook of Thermoelectrics, 1st Edition, CRC, Boca Raton (1994).
Schaevitz, S. B., Franz, A. J., Jensen, K. F., and Schmidt, M. A., “A combustion-based mems thermoelectric power generator”, The 11th International Conference on Solid-State Sensors and Actuators, June 10-14, Munich, Germany (2001).
Sitzki, L., Borer, K., Schuster, E., Ronney, P. D., and Wussow, S., “Conbustion in microscale heat-recirculating burners”, The Third Asia-Pacific Conference on Combustion, June 24-27, Seoul, Korea (2001).
Sinoda, M., Tanaka, R., and Arai, N., “Optimization of heat transfer performances of a heat-recirculating ceramic burner during methane/air and low-calorific-fuel/air combustion”, Energy Conversion and Management, Vol. 43, pp. 1479-1491(2002).
Weinberg, F. J., Advanced Combustion Methods, 1st ed., Academic, London (1986).
Weinberg, F. J., Rowe, D. M., Min, G., and Ronney, P. D., “On thermoelectric power conversion from heat recirculating combustion systems”, Proc. Combust. Inst., Vol. 29, pp. 941-947 (2002).
王志華,“潔淨能源:超焓燃燒器研發”國立中央大學機械工程研究所,碩士論文(2002)。
吳昇哲,“小型熱再循環觸媒燃燒器之實驗研究及應用”國立中央大學機械工程研究所,碩士論文(2003)。
李秉傑、邱宏明和王奕凱,“非均勻系催化原理與應用”渤海堂文化,台北市(1988)。
徐德勝,“半導體製冷與應用技術”上海交通大學出版社,第二版(1999)。
陳冠邦,“氣化生質能於白金蜂巢式反應器之觸媒燃燒研究”國立成功大學航空太空工程研究所,博士論文(2001)。
陳志挺,“Bi2Te3塊材與奈米微粒之熱電效率、熱傳導率與比熱之物性研究”私立淡江大學物理學系,碩士論文(2003)。
許紘偉、陳冠邦、謝維昇和趙怡欽,” 觸媒燃燒技術應用於氣化生質燃料氣渦輪燃燒室之可行性評估” 第三屆中華民國「民航學會/航太學會/燃燒學會」學術聯合會議,論文集,pp. 671-678(2002)。?
陳彥志,“潔淨能源:高效率天然氣加氫燃燒技術與污染排放物定量量測”國立中央大學機械工程研究所,碩士論文(2002)。
謝維昇,“觸媒氣渦輪引擎原型之發展”國立成功大學航空太空工程研究所,碩士論文(2003)。指導教授 施聖洋(Shenqyang Shy) 審核日期 2004-7-19 推文 plurk
funp
live
udn
HD
myshare
netvibes
friend
youpush
delicious
baidu
網路書籤 Google bookmarks
del.icio.us
hemidemi
myshare