TFT-LCD 導光板衝擊模擬分析及驗證研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：22

、訪客IP：18.227.46.196

姓名

王玉仙(Yu-hsien Wang) 查詢紙本館藏

畢業系所

機械工程學系在職專班

論文名稱

TFT-LCD 導光板衝擊模擬分析及驗證研究

相關論文

★ TFT-LCD前框卡勾設計之衝擊模擬分析與驗證研究	★ 數位機上盒掉落模擬分析及驗證研究
★ 旋轉機械狀態監測-以傳動系統測試平台為例	★ 發射室空腔模態分析在噪音控制之應用暨結構聲輻射效能探討
★ 時頻分析於機械動態訊號之應用	★ VKF階次追蹤之探討與應用
★ 火箭發射多通道主動噪音控制暨三種線上鑑別方式	★ TFT-LCD衝擊模擬分析及驗證研究
★ TFT-LCD掉落模擬分析及驗證研究	★ TFT-LCD螢幕掉落破壞分析驗證與包裝系統設計
★ 主動式火箭發射噪音控制使用可變因子演算法	★ 醫學/動態訊號處理於ECG之應用
★ 光碟機之動態研究與適應性尋軌誤差改善	★ 具新型菲涅爾透鏡之超音波微噴墨器分析與設計
★ 醫用近紅外光光電量測系統之設計與驗証	★ 車用DVD光碟機之適應性聚焦伺服控制實現與應用

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

本研究對TFT-LCD (Thin film transistor liquid crystal display)之導光板(Light guide plate)進行衝擊分析及試驗驗証，由於衝擊時間短暫，要去了解其受衝擊時反應相當不易，研究中採用兩種方式—衝擊試驗驗証與有限元素模擬分析，探討TFT-LCD模組受衝擊時之動態行為，藉由數值模擬與實驗兩者相互印証，以對結構設計提出適切改善。為了TFT-LCD模組設計能達到在模具開發製作前就加以評估的目的，研究中使用有限元素軟體MSC-Dytran對TFT-LCD模組進行衝擊模擬，預測TFT-LCD模組衝擊時整體的力學行為，並與實驗結果比較，進行分析模型修正；隨後對TFT-LCD模組進行設計改善，建立TFT-LCD模組設計的分析評估方式。
衝擊試驗是了解產品能承受多大衝擊的指標，能承受的衝擊值愈大，產品的可靠度愈高，本研究中對產品進行Y方向衝擊，探討所造成的衝擊響應，藉由衝擊試驗找出產品結構上的弱點進行改善，進而提高產品的可靠度。試驗結果不僅可以了解TFT-LCD模組可能發生的變形，並能驗證有限元素分析模式的合理性。由TFT-LCD模組有限元素分析過程中，發現LGP 固定處受衝擊時有高應力區現象，和衝擊試驗結果發生脆裂的地方吻合，進而以有限元素分析對此作設計改善，其改善方式為結合背板(Back cover)上之銅柱，多增加一處卡榫，經過模擬分析與衝擊試驗比對後，證實對策有效且可消除原先高應力區現象。
本文以試驗及模擬，建立了TFT-LCD模組設計的評估方式，應用實驗與數值模擬方法，可以有效地進行TFT-LCD模組設計，有助於開發初期設計驗證預估，縮短開發時程，快速導入量產，提高產品在業界的競爭力。

摘要(英)

This research is centered on the impact test analysis and test examination for the light guide plate of the TFT-LCD(Thin film transistor liquid crystal display)module. Due to extremely short duration of impact test, it is quite difficult to realize the impact response. This research is adopted with two methods — the impact test for examination and the finite element analysis model. Through the finite element analysis and experiment for truth examination of TFT-LCD module during impact test, we propose the adequate design improvement for the structure design. In the purpose of the evaluation of TFT-LCD module design before the developing mold period, the simulation of impact test on the TFT-LCD module is analyzed by MSC-Dytran finite element software which can predict the whole dynamic action of TFT-LCD module during impact test and compare to the experimental results to modify the analysis model. Thus, we can improve the design on TFT-LCD module and establish the analysis evaluation method of the TFT-LCD module design.
The impact test is aimed to understand the maximum indicating value of impact resistance for products. The large value means that products come with higher reliability. In this research, we conducted Y direction impact onto products to investigate the impact response. Through impact test, we could figure out the structure weakness of products and also increased the product reliability. The test results not only reveal the possible deformation of the TFT-LCD module but also examine the reasonability for the finite element analysis model. Under the process of the finite element analysis of the TFT-LCD module, we found that Light guide plate linkage parts would be affected by impacted and showed high stress area phenomenon which match the crack parts happening to the impact test. Thus, we proposed further design improvement by means of the finite element analysis. The improvement was that we combine the copper cylinder by adding stopper. After the comparison of the simulation analysis and the impact test, we confirmed that the improvement effectively and also eliminate the high stress area phenomenon.
This research developed the evaluated model for TFT-LCD module design after testing and simulation. It can be effective for the design of the TFT-LCD module by applied to experimental and value simulated methods. Thus it can help designers pre-estimate the product strength during the beginning of the development and also shorten the design duration, quickly bring out to mass production to exalt the industry competence of the products.

關鍵字(中)

★ 衝擊
★ 液晶面板

關鍵字(英)

★ Shock
★ TFT-LCD

論文目次

摘要 I
Abstract II
誌謝 III
目錄 IIV
圖目錄 VI
表目錄 VIII
第一章緒論 1
1.1 研究動機與目的 1
1.2 相關文獻回顧 2
1.3 TFT-LCD 介紹 3
1.4 研究架構 5
1.5 研究範圍 6
第二章理論背景 7
2.1 衝擊理論 7
2.1.2 衝擊運動 7
2.1.3 半正弦波脈衝響應 8
2.2 有限元素法應用於衝擊分析 9
2.2.1 隱性積分 9
2.2.2 顯性積分法 11
第三章衝擊試驗 13
3.1 試驗設備 13
3.2 試驗方法與流程 19
3.3 試驗結果 20
第四章衝擊模擬分析 24
4.1 有限元素模型 24
4.2 構件材料性質 29
4.3 鎖附邊界條件 30
4.4 接觸問題 30
4.5 模擬與試驗比對 35
4.6導光板卡榫探討 43
第五章設計改善 45
5.1 導光板改善對策確認 47
5.2導光板設計範圍探討 53
第六章結論與建議 56
參考文獻 57
附錄一 58
材料參數資料來源： 58

參考文獻

C.K. Chang, “The FEM Analysis for Mold Frame Design of TFT-LCD Module,” Proceedings of 2004 MSC.Software Taiwan Conference.
S.S. Choi, E. Kang and D.C. Kim, 1998, “Drop impact simulation for optimum design of TFT-LCD,” Proceedings of the IEEE Intersociety Conference on Thermal Phenomena in Electronic Systems, pp.2-11.
S.S. Choi, J.G. Lee, “Structural Design Review of LCD-TV Module by Impact Analysis,” Proceedings of 2003 4th European LS-DYNA User Conference, pp.GII-01-09.
K.D. Ha, D.W. Kim and J.K. In, “Prediction of CRT Shock Test and Design Improvement for Shock Resistance,” Proceedings of SID 2000, pp.952-955.
J.D. Helfinstine, S. T. Gulati, J. F. Bayne, W. R. Powell and J. C. Lapp, 2004, “Mechanical reliability of LCD panels under dynamic loading,” Proceedings of SID 2004 Digest, pp.1597-1599.
J.D. Helfinstine, S. T. Gulati, J. F. Bayne, W. R. Powell and J. C. Lapp, 2004, “Mechanical reliability of LCD panels under static loading,” Proceedings of SID 2004 Digest, pp.1593-1596.
R.C. Junival, 1967, ”Stress Strain and Strength”, Mc-Graw-Hill, pp.79-80.
C.S. Kim, K.B. Shin, S.W. Booh and W.Y. Soh, “The Simulation Based Drop/Impact Design of PDP Module,” Proceedings of SID 2002, pp.737-739.
J.H. Kim, K.H. Song and W.Y. Soh, “A New Shadow Mask Assembly Improved the Impact Strength,” Proceedings of SID 2001, pp.1219-1221.
D.W. Kim, I.S. Cho and K.S. Lee, 2004, “Computational shape optimization for strength improvement of 42 in. PDP aluminum chassis with Al. reinforcement,” Proceedings of SID 2004 Digest, pp.1600-1603
N.H. Nan and C.C. Huang, 2005, “The FEM analysis for LCD module of clammer-type handset during drop,” Proceedings of 2005 MSC.Software Conference.
M.C. Pan, P.C. Chen and J. Ho, “Drop Simulation and Experiment Validation of TFT-LCD Monitors,” Electronics Packaging Technology Coference,2003, pp.269-274.
D.S. Steinberg., 1988, “Vibration analysis for electronic equipment,” John Wiley & Sons, Inc., New York.
T.Y. Tee, J.E. Luan, Eric Pek, C.T. Lim and Z.W. Zhong, 2004, “Noval numerical and experimental analysis of dynamic responses under board level drop test,” 5th Int. Conf. on Thermal and Mechanical Simulation and Experiments in Micro-electronics and Micro-system, EuroSimE2004, pp.133-140.
MSC.Dytran Reference Manual
王柏村, 2001,”電腦輔助工程分析之實物與應用”,全華圖書。
陳君明, 2003, “TFT-LCD衝擊模擬分析及驗證研究” , 國立中央大學碩士論文。
陳伯群, 2003, “TFT-LCD掉落模擬分析及驗證研究” , 國立中央大學碩士論文。

指導教授

潘敏俊(Min-Chun Pan)

審核日期

2007-7-23

推文