甲醇鈉之製備與其與二氯甲烷之液-固相轉移催化甲氧基取代

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：86

、訪客IP：3.149.250.19

姓名

王冠文(Guan-Wun Wang) 查詢紙本館藏

畢業系所

化學工程與材料工程學系

論文名稱

甲醇鈉之製備與其與二氯甲烷之液-固相轉移催化甲氧基取代
(The preparation of Sodium Methoxide and the S-L Phase-Transfer Catalyzed Methoxy Substitution of Dichloromethane.)

相關論文

★ 以溴化四丁基銨鹽電解-電透析合成醋酸四丁基銨鹽及該鹽之精製	★ 溴化四丁基銨鹽之製備與其電解─電透析方法以合成氯化四丁基銨鹽之研究
★ 彩色濾光片再生製程強鹼染料廢水之電解-電透析處理以去除廢水中之KOH，並同時合成KOH與NaOCl	★ 彩色濾光片玻璃基板再生製程強鹼染料廢液之催化濕式氧化處理
★ 甚高濃度有機廢水之催化溼式氧化處理	★ 甚高有機污染強鹼廢水之電透析前處理
★ 醋酸丁酯之液-固相轉移催化合成及其水解研究	★ 醋酸丙烯酯之液-固相轉移催化合成及其水解研究
★ 鹵化四丁基銨之合成動力學、溶解、萃取及精製研究	★ 醋酸戊酯之相轉移催化水解以合成正戊醇之研究
★ 四丁基銨鹽之溶解度、締合常數、活性係數及分佈係數	★ 溶劑與陰離子(Y)之結構對一典型相轉移催化親核取代反應BzCl + Bu4NY→BzY + Bu4NCl之反應性之效應
★ 溶劑、親核劑(QBr)陽離子之結構及溫度對相轉移催化反應BzCl + QBr<--> BzBr + QCl 之反應性之效應	★ 溶劑、基質結構及溫度對相轉移催化親核取代反應ROH + Bu4NCl<-->RCl +Bu4NOH 之反應性之效應
★ 2-胺基噻吖唑衍生物合成與其性質之探討	★ 合成1,3-双[5-苯基-1,3,4-

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

本研究在探討甲醇鈉之製備與其及二氯甲烷之液-固相轉移催化甲氧基取代。理論推究兩相中之物理與化學程序，得知溶劑之種類與劑量、相轉移催化劑種類與劑量、攪拌速度以及反應溫度為影響總反應速率及產物分佈的因素，並遂一實驗求得最適反應條件如下：
甲醇鈉之製備：在甲醇1.2 mol、氫氧化鈉1 mol、催化劑（BzBu3NCl）劑量為甲醇的10％、氯化鈣0.1 mol、反應溫度50℃及攪拌速度200 rpm等條件下，反應八小時，抽氣過濾後，再以100～150℃蒸出甲醇則可得甲醇鈉固體約20 g（收率約60％）。
二甲氧基甲烷之製備有以下兩種方法：
I. 在甲醇鈉2 mol、二氯甲烷1 mol、溶劑THF約為0.6 mol、催化劑（BzBu3NCl）劑量為甲醇鈉的10％、反應溫度50℃及攪拌速度200 rpm等條件下於250mL之三頸圓底燒瓶，反應約一天半，可得二甲氧基甲烷產率達90％以上。
II. 在甲醇2.2 mol、氫氧化鈉3.2 mol、二氯甲烷1 mol、溶劑THF約為0.6 mol、催化劑（BzBu3NCl）劑量為甲醇的10％、反應溫度50℃及攪拌速度200rpm等條件下，反應約三小時，可得二甲氧基甲烷產率約85％。

摘要(英)

The preparation of sodium methoxide and the phase-transfer catalyzed methoxy substitution of dichloromethane were studied. The physical and chemical processes were considered to derive the overall production rate equation for methylal. The factors (the types and amounts of the solvents, the kinds and amounts of phase-transfer catalysts, the stirring speed and the reaction temperature) affecting the overall reaction rate and the product distributed were studied. The results can be explained with the overall rate equation.
Sodium methoxide was prepared as follows: methanol 1.2 mol, sodium hydroxide 1 mol and phase-transfer catalyst (BzBu3NCl) amounts of 10% methanol, reaction temperature 50℃and stirring speed 200 rpm. Reaction time about 8 hours, vacuum-filter and distillation in 100~150℃, we can recycle methanol and obtain pure sodium methoxide solid.
The dimethoxymethane was synthesized by method I and method II.
Method I: sodium methoxide 2 mol, dichloromethane 1 mol, solvent (THF) 0.6 mol and phase-transfer catalyst (BzBu3NCl) amounts of 10% sodium methoxide, reaction temperature 50℃and stirring speed 200 rpm. Reaction time about 30 hours, we can obtain about 90% dimethoxymethane.
Method II: methanol 2.2 mol, sodium hydroxide 3.2 mol, dichloromethane 1 mol, solvent (THF) 0.6 mol and phase-transfer catalyst (BzBu3NCl) amounts of 10% methanol, reaction temperature 50℃and stirring speed 200 rpm. Reaction time about 3 hours, we can obtain about 50% dimethoxymethane.

關鍵字(中)

★ 甲醇鈉
★ 二氯甲烷
★ 甲氧基取代
★ 相轉移催化

關鍵字(英)

★ Methoxy Substitution
★ Dichloromethane
★ Sodium Methoxide
★ Phase-Transfer Catalyzed

論文目次

中文摘要..............................i
英文摘要..............................ii
誌謝..............................iii
目錄..............................iv
圖目錄..............................v
符號說明..............................vi
第一章　　緒　論..............................1
1-1 相轉移催化之起源與定義..............................1
1-2 相轉移催化之原理及系統形態..............................1
1-2-1　相轉移催化之原理..............................1
1-2-2　相轉移催化之系統形態..............................2
1-3 相轉移催化劑之種類.............................. 3
1-4 甲醇鈉之經濟性、來源與用途..............................5
1-5 甲醇鈉之合成..............................6
1-6 二甲氧基甲烷之經濟性、來源與用途..............................6
1-7 二甲氧基甲烷之合成.............................. 7
1-8 本研究的動機與主旨 ..............................9
第二章　　理　論..............................10
2-1 親核取代反應..............................10
2-1-1　單分子親核取代反應..............................10
2-1-2　相轉移催化之系統形態 ..............................11
2-1-3　相轉移催化之親核取代反應..............................11
2-2 液-固反應系統之化學程序與質傳程序..............................11
2-3 液-固反應系統中二甲氧基甲烷之總生成速率方程式..............................12
2-4 液-固系統中影響二甲氧基甲烷之總生成速率之因素..............................16
2-4-1　相轉移催化劑結構之影響..............................16
2-4-2 相轉移催化劑劑量之影響..............................16
2-4-3 溶劑之影響..............................17
2-4-4 攪拌速率之影響..............................17
2-4-5 溫度之影響..............................17
第三章　　實驗部份..............................19
3-1 藥品..............................19
3-1-1　實驗及分析用之藥品..............................19
3-1-2　相轉移催化劑之製備..............................20
3-1-3　甲醇鈉之製備..............................21
3-2 實驗裝置及分析儀器.............................. 21
3-2-1　實驗裝置..............................21
3-2-2　氣相層析儀..............................22
3-3 樣品分析..............................22
3-3-1　氣相層析儀(GC)之校正曲線..............................22
3-3-2　氣相層析儀(GC)之分析條件..............................22
3-3-3　氣相層析儀(GC)之樣品分析..............................24
3-4 實驗之操作..............................24
3-5 二甲氧基甲烷製備程序之實驗步驟..............................24
3-5-1　相轉移催化劑結構之影響..............................24
3-5-2　溶劑之影響..............................24
3-5-3　相轉移催化劑劑量之影響..............................25
3-5-4　攪拌速率之影響..............................25
3-5-5　溫度之影響..............................25
3-5-6　適當實驗條件..............................25
第四章　　結果與討論..............................26
4-1 相轉移催化劑結構之影響..............................26
4-2 溶劑之影響..............................28
4-3 相轉移催化劑劑量之影響..............................30
4-4 攪拌速率之影響..............................30
4-5 溫度之影響..............................30
4-6 適當實驗條件..............................35
4-6-1　三頸圓底燒瓶系統..............................35
4-6-2　密閉式反應器系統..............................35
4-6-3　製備甲醇鈉法..............................35
第五章　　結論..............................40
參考文獻..............................41
附錄一..............................45
附錄二..............................46

參考文獻

[1] J. Jarrouse and C. R. Hebd. Seances Acad. Sci. Ser., C232, 1424 (1951).
[2] C. M. Starks, “Phase-transfer Catalysis. I. Heterogeneous Reaction Involving Anion Transfer by Quaternary Ammonium and Phosphonium Salts” J. Am. Chem. Soc., 93(1), 195 (1971).
[3] 朱紫瑛，「醋酸丙烯酯之相轉移催化水解以合成丙烯醇及該法用於其它醋酸酯之水解之研究」，國立中央大學，Dept. of Chemical and Materials Engineering, 碩士論文，民國84年。
[4] 張詠鈞，「氯化戊烷之相轉移催化醋酸根取代以合成醋酸戊酯之研究」，國立中央大學，Dept. of Chemical and Materials Engineering, 碩士論文，民國87年。
[5] E. Angeletti, P. Tundo and P. Venturello, “Gas-Liquid Phase-Transfer Catalysis: Catalytic and Continuous Transesterification Reaction”, J Org. Chem., 48, 4106-8(1983).
[6] 吳和生，「液-固-液三相反應動力學之應用-醚酯類」，第十五屆台灣區觸媒及反應工程研討會論文集（1997）。
[7] 周子卿，「有機金屬催化氫化以合成環己烷之研究」，國立中央大學，Dept. of Chemical and Materials Engineering, 碩士論文，民國88年。
[8] P. Tundo and P. Venturello, “Silica Gel Supported Phosphonium Salts as Micellar and Phase-Transfer Catalysis”, Tetrahedron Lett. 21, 2581 (1984).
[9] Starks C. M., “Selecting a Phase Transfer Catalysis”, Chemtech, 110 (1980).
[10] P. Hodge, and D. C. Sherrington, “Polymer-supported Reaction in Organic Synthesis”, John Wiley and Sons, 1980.
[11] 徐金榮，「葡萄糖之有機金屬相轉移催化氫化研究」，國立中央大學，Dept. of Chemical and Materials Engineering, 碩士論文，民國83年。
[12] 德豐藥品集團：甲醇鈉介紹。取自http://www.defengchem.com.cn/cgi/search-cn.cgi?f=product_cn+product_cn_1_+company_cn_1_+contact_cn&id=331415&t=product_cn_1_。
[13] Burness, D. M. “Methyl 3-methyl-2-furoate”, Organic Syntheses, Coll. Vol. 4, p. 649 (1963); Vol. 39, p. 49 (1959).
[14] 陳介武：生質柴油焦點。取自http://www.asaim.org.tw/biodiesel-39.pdf。
[15] 中國石油化工信息網：甲醇鈉項目技術轉讓。取自 http://www.zshg.com/infofromuser/info_detail.asp?InfoID=1518。
[16] Sun, Xiangdong et al., "Preparation of sodium methylate with metallic sodium.",
[17] Huagong Shengchan Yu Jishu Bianjibu, 10(5), 35-37 (2003).
[18] Koehler, Guenther et al., “Procedure for the production of alkali metal alcoholates and alkaline earth metal alcoholates with water separation by membrane pervaporation.”, Ger. Offen. Patent 10,158,353 (2003)
[19] 中國貿易網：有機化工原料。取自 http://www.cntrades.com/Leadshtml/leads130332.htm。
[20] 中國化工商貿網：醛類。取自 http://hg.ztrade.net/product/showinfo.asp?id=226143713。
[21] 任毅等發表，「柴油機燃用柴油卅二甲氧基甲烷混合燃料的性能與排放研究」，內燃機學報，1000-0909(2004)
[22] 百度百科：甲缩醛。取自http://baike.baidu.com/view/694906.htm?func=retitle。
[23] Yuan, Yu-hang et al. "Ti2O nano tube supported V2O5 composite catalyst.", Huagong Shengchan Yu Jishu Bianjibu, 34(1), 16-18,65 (2008).
[24] Fu, Yuchuan, and Shen, Jianyi. "Selective oxidation of methanol to dimethoxymethane under mild conditions over V2O5/TiO2 with enhanced surface acidity.", Royal Society of Chemistry, (21), 2172-2174(2007).
[25] Hine, Jack, Duke, Roy B. and Glod, Edward F. "Mechanism of the Reaction of Methylene Halides with Alkali Metal Alkoxides in Alcohol Solution.", Journal of the American Chemical Society, 91(9), 2316-24(1969).
[26] Guan, Xiaowei et al. "One-step synthesis of dimethoxymethane catalyzed by p-toluenesulfonic acid.", Jisuanji Yu Yingyong Huaxue Bianjibu, 24(6), 823-826(2007).
[27] L. M. Starks, and C. Liotta, “Phase Transfer Catalysis, Principles and Techniques”, Academic Press, New York, 1978.
[28] McMurry, “Organic Chemistry”, Cole Publishing Company, Montery, California, 307(1984)
[29] R. T. Morrison, and R. N. Boyd, “Organic Chemistry”, 5th Allyn & Bacon, Inc., 183(1987)
[30] 張其晃，「有機鹵化物與季銨鹼之親核雙取代反應研究」，國立中央大學，Dept. of Chemical and Materials Engineering, 碩士論文，民國80年。
[31] D. Forster, J. Chem. Soc., Chem. Commun., 918(1975)
[32] D. Landini, A. Maia and F. Montanari, J. Chem. Soc., Chem. Comm., 112(1977)
[33] D. Feldman, D. S. Lew and M. Rabinovitz, “Nucleophilic Aromatic Substitution by Hydroxide Ion under Phase-Transfer Catalysis Conditions Fluorine Displacement in Polyflurobenzene”, J. Org. Chem. 56, 7350(1991).
[34] T. T. Wang, T. C. Huang and M. Y. Yeh, “Benzyl Ether from Phase Transfer Catalyzed Strongly Alkaline Hydrolysis of Benzyl Chloride”, J. Mol. Cat. 57, 271(1990).
[35] T. T. Wang, T. C. Huang and M. Y. Yeh, “Benzyl Acetate from Phase Transfer Catalyzed Acetate Displacement of Benzyl Chloride”, Chem. Eng Comm. 100, 135(1991).
[36] E. V. Dehmlow, and J. Schmidt, Tetrahedron Lett., 95(1976)

指導教授

王天財(Ten-Tsai Wang)

審核日期

2009-6-22

推文