博碩士論文 105353030 詳細資訊




以作者查詢圖書館館藏 以作者查詢臺灣博碩士 以作者查詢全國書目 勘誤回報 、線上人數:80 、訪客IP:44.211.35.130
姓名 許銘維(Ming-Wei Hsu)  查詢紙本館藏   畢業系所 機械工程學系在職專班
論文名稱 搖臂軸承心軸高週波硬化處理參數研究
(The study of rocker arm bearing shaft high frequency hardening treatment parameters)
相關論文
★ 使用實驗計劃法求得印刷電路板微鑽針最佳鑽孔參數★ 滾針軸承保持架用材料之電鍍氫脆研究
★ 強制氧化及熱機處理對鎂合金AZ91D固相回收製程之研究★ 滾針軸承保持架圓角修正之有限元素分析
★ 透過乾式蝕刻製作新型鍺全包覆式閘極電晶體元件★ 窗型球柵陣列構裝翹曲及熱應力分析
★ 冷軋延對ZK60擠製材的拉伸與疲勞性質之影響★ 熱引伸輔助超塑成形製作機翼整流罩之設計及分析
★ 超塑性鋁合金5083用於機翼前緣整流罩之研究★ 輕合金輪圈疲勞測試與分析
★ 滾針軸承保持架之有限元分析★ 鎂合金之晶粒細化與超塑性研究
★ 平板式固態氧化物燃料電池穩態熱應力分析★ 固態氧化物燃料電池連接板電漿鍍膜特性研究
★ 7XXX系鋁合金添加Sc之顯微組織與機械性質研究★ 高延性鎂合金之特性及成形性研究
檔案 [Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   [檢視]  [下載]
  1. 本電子論文使用權限為同意立即開放。
  2. 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
  3. 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。

摘要(中) 搖臂軸承主要用於摩托車發動機汽缸蓋凸輪機構,承擔閥門的正常開、關功能,在發動機內燃料與燃燒氣體的進氣、排氣中起著重要作用。發動機運行中凸輪會不停轉動,以前採用滑塊式搖臂,現行使用摩擦更小的方式"滾動接觸”替代。搖臂軸承在滾動時心軸需承受碰撞及摩擦,由於應力產生與破壞常集中在心軸與滾針線接觸面,所以如何使心軸硬度達到合理範圍,是攸關品質好壞與整體軸承使用壽命之表現。
本文由廠商回饋之問題,將產品以壽命試驗機測試之,針對未達規範之搖臂軸承分析心軸硬度之分佈及金相組織之情況,以田口實驗法分析不同之高週波熱處理參數,對硬度及金相之影響,給予修正模擬不同的加熱時間、淬火時間、加熱位置、線圈形狀,觀察期變化的狀況;另將此數據建立起來,以利後續產品開發時程。
摘要(英) The rocker arm bearing is mainly used in a cylinder head cam mechanism of a motorcycle engine and assumes the opening and closing functions of the valve. It plays an important role in the intake and exhaust of fuel and combustion gases in the engine. In the running of the engine, the cam will rotate constantly. The slider rocker arm was used in the past. The current method of "rolling contact" is used instead of friction. When the rocker bearing is rolling, the shaft needs to bear the collision and friction. Since the stress generation and damage often focus on the contact surface between the shaft and the needle , how to make the hardness of the shaft reach a reasonable range is the quality of the bearing and the service life of the whole bearing. Performance.
This article is feedback by customer, the product is tested with a life tester, and analysis of the distribution of the shaft hardness and the metallographic structure of the rocker bearing that is not up to specification is performed. The Taguchi method is used to analyze different high-frequency heat treatment parameters. The effects of hardness and metallography were given to simulate different heating time, quenching time, heating position, coil shape, observation period change status; this data was also established to facilitate the follow-up product development schedule.
Keywords: Rocker bearing shaft, Taguchi method, High frequency heat treatment
關鍵字(中) ★ 搖臂軸承
★ 高週波加熱
關鍵字(英) ★ rocker arm
★ bearing
★ high frequency
論文目次 摘要 …………………………………………………………………………………………II
ABSTRACT …………………………………………………………………………………III
目錄 …………………………………………………………………………………………V
表目錄 ……………………………………………………………………………………VIII
圖目錄 ………………………………………………………………………………………IX
符號說明 …………………………………………………………………………………XII
第一章 緒論 ………………………………………………………………………………1
1-1 前言…………………………………………………………………………1
1-2 文獻回顧……………………………………………………………………4
1-3 研究動基與目的……………………………………………………………6
1-4 論文架構與內容……………………………………….…………………11
第二章 理論基礎 ………………………………………………………………………12
2-1 高週波感應加熱基本原理 ………………………………………………12
2-1-1 渦電流損失 ………………………………………………………12
2-1-2 磁滯損失 …………………………………………………………14
2-1-3 高週波滲透深度 …………………………………………………15
2-1-4 頻率及表皮效應 …………………………………………………17
2-2 高週波感應加熱特性 ……………………………………………………19
2-3 高週波感應加熱及金相組織 ……………………………………………20
2-3-1 電流轉化器的構造 ………………………………………………20
2-3-2 感應線圈的尺寸和形狀 …………………………………………20
2-3-3 淬火方式 …………………………………………………………21
2-3-4 感應線圈及加熱條件選定 ………………………………………22
2-3-5 冷卻劑及冷卻速度的選定 ………………………………………23
2-4 變態點和沃斯田鐵狀態 …….……………………………………………25
2-5 高週波感應淬火用的鋼材 ………………………………………………27
2-5-1 機械性質 …………………………………………………………28
2-5-2 顯微組織 …………………………………………………………29
2-5-3 波來鐵、肥粒鐵與雪明碳鐵 ……………………………………30
2-5-4 沃斯田鐵 …………………………………………………………31
2-5-5 麻田散鐵 …………………………………………………………32
第三章 研究方法與步驟 ………………………………………………………………34
3-1 田口實驗設計流程………………………………………………………35
3-2 信號雜訊比………………………………………………………………36
3-3 直交表選擇………………………………………………………………37
3-4 變異數分析(ANOVA) ……………………………………………………38
3-5 F分布 ……………………………………………………………………40
3-6 實驗預測 ………………………………………………………………42
第四章 實驗設備及方法 ………………………………………………………………44
4-1 實驗設備及材料…………………………………………………………44
4-1-1 工件材料…………………………………………………………44
4-1-2 加工線圈…………………………………………………………45
4-1-3 實驗設備…………………………………………………………46
4-2 研究流程…………………………………………………………………50
4-3 實驗方法…………………………………………………………………51
4-3-1 實驗參數設定……………………………………………………52
4-3-2 直交法規劃………………………………………………………52
4-3-3 實驗步驟…………………………………………………………54
4-4 硬度及金相合格判定……………………………………………………55
4-4-1 滾針搖臂汽門軸承………………………………………………55
4-4-2 滾針軸承心軸硬度規範…………………………………………55
4-4-3 金相組織規範……………………………………………………57
第五章 .與分析討論 ……………………………………………………………………58
5-1 田口實驗設計加工參數最佳化…………………………………………58
5-2 ANOVA變異數分析 ………………………………………………………61
5-3 預測值與實驗驗證………………………………………………………64
第六章 結論及未來展望 ………………………………………………………………69
6-1 結論………………………………………………………………………69
6-2 未來展望…………………………………………………………………70
參考文獻……………………………………………………………………………………72
附錄(一)……………………………………………………………………………………80
附錄(二)……………………………………………………………………………………82
參考文獻 [1] 趙祥編著 “機械原理及機械零件”,第14章-軸承,中國鐵道出版社,1998。
[2] 張一屏,”滾針軸承保持架熱處理多目械性能最佳化分析”,國防整體後勤支援年·暨研討會(2000)。
[3] Xu, Jiandon”Experimental study on the kinematic relationships of cylindrical roller bearing.”Mocaxue Xuebao/Tribology,Vol. 15′n4,p. 373-375 (1995) ·
[4] P.G.Hoch"Influence of radial accelerations on plastics cages in roll ing bearings.”Ball Bearing Journal,n228,Nov,p. 6-12 (1986)。
[5] Frank W. Curtis, “High-Frequency Induction Heating,” McGraw-Hill Book Company, 1950.
[6] 李輝煌著 ”田口方法:品質設計的原理與實務第四版”,高立圖書有限公司,2015。
[7] 田口玄一 著,陳耀茂 譯 ”田口統計解析法”,五南圖書出版公司,2003。
[8] Jack G.Zhou, Daniel Herscovici, Calvin C.Chen. Parametric Process Optimization to Improve the Accuracy of Rapid Prototyped Stereolithography Parts. International Journal of Machine Tools &Manufacture 40 pp.363-379
[9] 黃振賢,機械材料,新文京開發出版有限公司,民國91年6月
[10] 余煥騰,金屬熱處理學,六合出版社,民國 76 年 10 月。
[11] 謝淵清,新版熱處理學技術,復文書局,民國 74 年 2 月。
[12] 黃振賢,機械材料,新文京開發出版有限公司,民國 91 年 6 月。
[13] Y. Totik R. Sadeler, H A1mui, M. Gavgali."The effects of induction hardening on wear properties of AISI 4140 steelin dry sliding conditiolts.”Materials & Design,vol. 24,Issue 1,2003,pp.25-30。
[14]Y. Wang, T. Lei, “Wear behaviour steel 1080 with different microstructures during dry sliding,” Wear,
[15] D-H. Xu, Z-B. Kuang, “A Study on the Distribution of Residual Stress Due to Surface Induction Hardening, Journal of Engineering Materials and Technology, vol. 118, Issue 4, 1996, pp.571-575。
[16]H.Kristoffersen, P. Vomacka, “Influence of process parameters for induction hardening on residual stress,” Materials & Design, vol. 22, Issue 8, 2001, pp.637-644
[17]F. Cajnera, B. Smoljanb, D. Landeka, “Computer simulation of induction hardening,” Journal of Materials Processing Technology, vol. 157-158, 2004, pp.55-60
[15]I. Magnabosco, P. Ferro, A. Tiziani, F. Bonollo, “Induction heat treatment of ISO C45 steel bar: Experimental and numerical analysis,” Computational Materials Science, vol. 35, Issue 2, 2006, pp.98-106.
[16]K.F. Wang, S. Chandrasekar, H.T.Y. Yang,” Experimental and computational study of the quenching of carbon steel,” Journal of Manufacturing Science and Engineering, vol. 119, Issue 3, 1997, pp. 257-265.
[17]ASM Handbook, Heat treating, vol. 4, 1998.
[18]O. Kessler, T. Herding, F. Hoffmann, P. Mayr, “Microstructure and wear resistance of CVD TiN- coated and induction surface hardened steels,” Surface and Coatings Technology, vol. 182, Issues 2-3, 2004, pp.184-191.
[19] C.R.F. Azevedo, J. Belotti Neto, “Failure analysis of forged and induction hardened steel cold work rolls,” Engineering Failure Analysis, vol. 11, Issue 6, 2004, pp.951-966.
[20]Y.C. Chen, and K. Nakata, “Evaluation of microstructure and mechanical properties in friction stir processed SKD61 tool steel,” Materials Characterization, Vol. 60, Issue 12, 2009, pp.1471-1475.
[21]R. Ueji, H. Fujii, L. Cui, A. Nishioka, K. Kunishige, K. Nogi, “Friction stirwelding of ultrafine grained plain
low-carbon steel formed by the matrensite process,” Materials Science and Engineering: A, Vol. 423, Issues 1-2, 2006,pp324-330.
[22]Ling Cui, Hidetoshi Fujii, Nobuhiro Tsuji, Kiyoshi Nogi, “Friction stir welding of a high carbon steel,” Scripta Materialia, Vol. 56, Issue 7, 2007, pp637-640.
[23]M.H. Kim, K.Y. Rhee, Y.N. Paik , J.S. Hong, Y.S. Ham “Experimental investigation on the mechanical behavior of high-frequency induction-hardened mild carbon, SPS5 steel,” Materials Science and Engineering A, vol. 485, Issue 1, 2008, pp.31–38.
[24]J. Komotori, M. Shimizu Y. Misaka, K. Kawasaki, “Fatigue strength and fracturemechanism of steel modified by super-rapid induction heating and quenching,” International Journal of Fatigue, vol. 23, 2001, pp.225-230.
[25]Smith, K.C., Van Tyne, C.J., and Robino, C.V., “Effect of Heating Rate, Composition, and Prior Microstructure on Austenite Formation in Medium Carbon Steels,” ASPPRC Bar and Forging Report, Section 5.0, 2002.
[26]Coryell, J.J., Matlock, D.K., and Speer, J.G., “Effects of Induction Processing on the Mechanical Properties of Steels With Controlled Microstructures,” ASPPRC Bar and Forging Report, Section 5.0, 2003.
[27]J. D. Wong, D. K. Matlock, G. Krauss, “Effects of
Induction Tempering on Microstructure, Properties and Fracture of Hardened Carbon Steels,” 43rd Mechanical Working and Steel Processing Conference; Charlotte, NC, USA, 2001, pp.21-36
[28]D. J. Medlin, G. Krauss, S.W. Thompson, “Induction Hardening Response of 1550 and 5150 Steels with Similar Prior Microstructures,” presented at 1st International Conference on Induction Hardening of Gears and Critical Components; Indianapolis, IN, 1995.
[29]A. Reguly, T. R. Strohaecker, G. Krauss, D. K. Matlock, “Quench Embrittlement of Hardened 5160 Steel as a Function of Austenitizing Temperature,“ Metallurgical and Materials Transactions A, Vol. 35A, 2004, pp. 153-162.
[30]G. Krauss, “Deformation and Fracture in Martensitic Carbon Steels Tempered at Low Temperatures,” Metallurgical and Materials Transactions A, Vol. 32A, April 2001, pp. 861-877.
[31]J. L. Cunningham, D. J. Medlin and G. Krauss, “Effects of induction hardening and prior cold work on a microalloyed medium carbon steel,” Journal of Materials Engineering and Performance vol. 8, no. 4, 1999, pp.401-408.
[32]張季娜、羅仕勇,田口式品質工程導論,中華民國品質管制學會,1993。
[33]蘇朝墩,品質穩健設計,中華民國品質學會,1997。
[34] 陳耀茂,田口實驗計劃法,滄海書局,1997。
[35] 范光照,精密量測,高立書局,2000。
[36] 張郭益、許全守,精密量測,全華書局,2003。
[37] 張季娜、羅仕勇,田口式品質工程導論,中華民國品質管制學
會,1993。
[38] Coryell, J.J., Matlock, D.K., and Speer, J.G., “Effects of Induction Processing on the Mechanical Properties of Steels With Controlled Microstructures,” ASPPRC Bar and Forging Report, Section 5.0, 2003.
[39] 劉克琪,實驗設計與田口式品質工程,華泰書局,1984。
[40] 林朝蒼,田口品質工程,中山科學研究院品保中心,1989。
[41]A. Reguly, T. R. Strohaecker, G. Krauss, D. K. Matlock, “Quench Embrittlement of Hardened 5160 Steel as a Function of Austenitizing Temperature,“ Metallurgical and Materials Transactions A, Vol. 35A, 2004, pp. 153-162.
[42] 黎正中譯,穩健設計之品質工程,台北圖書有限公司,1983。
[43] M.P. Norton,“Fundamental of Noise and Vibration Analysis for Engineers,”Cambridge University Press, 1989
[44] B. Porat,“A course in digital signal processing,”John Wiley & Sons, Inc., 1997.
指導教授 李雄(Shyong Lee) 審核日期 2018-7-12
推文 facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu   
網路書籤 Google bookmarks   del.icio.us   hemidemi   myshare   

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明