以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：35

、訪客IP：18.221.53.209

姓名	郭幸宜(KUO HSING-YI)  查詢紙本館藏	畢業系所	環境工程研究所
論文名稱	污泥脫水濾液無機物成分之結垢潛勢研究 (An investigation on scaling potential of inorganic components in sludge dewatering filtrate)
相關論文	★ 以SDI與MFI指標評估工業廢水回收再利用之機會：以某散熱器製造業為例 ★ 以反應曲面法探討流體化床結晶回收磷酸亞鐵之影響因子 ★ 活性污泥異營與自營脫硝 反應動力特性之研究 ★ 沼渣施用對土壤及滲出水之重金屬成份影響分析 ★ 脈衝式曝氣對沉浸式薄膜生物處理系統 積垢控制之探討 ★ 以聚合硫酸鐵進行污泥調理脫水之綜合效能評估 ★ 以低亞硫酸鈉進行自營性脫硝反應之可行性研究 ★ 硫氮比、pH與溶氧對還原性硫化物自營脫硝反應之影響 ★ 以海水提升流體化床磷酸銨鎂結晶 之可行性研究 ★ 超音波水解生物污泥機制探討 ★ 生物除氮程序(MLE Process)效能評估及污泥活性探討 ★ 活性污泥除氮程序（OAO Process）效能評估與設計參數探討 ★ 廢水處理廠 COD 和 TN 水質細分類 與脫硝效率之研究 ★ 硫代硫酸鹽自營性脫硝之反應動力與亞硝酸鹽氮累積特性探討 ★ 以RO濃排水提升流體化床磷酸鹽結晶之可行性研究 ★ 以超聲波輔助化學氧化法處理廢棄 NF 膜之反應特性與膜再利用可行性評估
檔案	[Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   至系統瀏覽論文 (2024-9-30以後開放)
摘要(中)	由於近年磷礦開採量的上升，磷回收之議題逐漸受到重視。在污水廠中厭氧消化程序具有高磷與高氮之成分，但含有大量懸浮固體與有機物影響，容易使回收成效不佳。因此，藉由前處理之方式優化磷回收之品質，是未來實廠應用所需之程序，但透過薄膜過濾進行前處理時，容易遇到積垢與結垢之問題，導致過濾效率不佳，進而使成本上升及成效的降低。 因此，本研究使用合成脫水濾液進行無機物結垢潛力與磷保留率實驗，透過批次實驗與反應曲面法探討實廠濃度範圍之最佳條件，並利用長期薄膜過濾實驗以比較及驗證最佳條件與最差條件之結垢特性差異。 透過實廠廢水之水質分析中顯示，脫水濾液之pH為7.9±0.1、正磷酸鹽濃度為128.1±8.2 mg/L、氨氮濃度為771.3±68.1 mg/L、總固體濃度為1,163±80.1 mg/L及TOC為56.2±10.3 mg/L。厭氧消化上澄液之pH為7.6±0.6、正磷酸鹽濃度為170.7±42.0 mg/L、氨氮濃度為871.2±102.2 mg/L、總固體濃度為33,193±166.2 mg/L及COD為698.9±21.6 mg/L，二者相比，由於厭氧消化上澄液之懸浮固體與有機物較高之特性，較不易進行薄膜前處理與磷回收，而脫水濾液含有較少之懸浮固體且仍具有較高之磷濃度。因此，整體而言，脫水濾液具有較佳之回收潛力。 在批次實驗中使用不同pH值與鈣離子濃度進行MFI0.2與磷保留率之實驗，根據結果顯示當pH越高會造成越高MFI0.2與越低磷保留率。在pH 6－7中具有較低MFI0.2與較高磷保留率，主要因為產生沉澱反應之pH區間範圍約在pH 7.5－12，在低於該範圍時，不易有顆粒產生。在pH 7.5－9時，隨著pH的上升，溶液中離子積高於各類磷酸鹽化合物之KSP，如：磷酸銨鎂、羥基磷灰石等，並產生顆粒物，進而導致結垢產生。同時發現隨著pH與鈣離子濃度由低到高，MFI0.2、粒徑與可能產生之沉澱物種類皆逐漸上升，磷保留率則逐漸下降。 固定pH值，並在磷濃度1.5－4.5 mmol/L(46.46－139.37 mg/L)、鎂離子0.5－1.5 mmol/L(12.1－36.5 mg/L)及鈣離子0.75－2.25 mmol/L(30－120 mg/L)條件下使用反應曲面法進行規劃與分析，得到最佳解為當磷濃度1.5 mmol/L、鈣離子濃度0.75 mmol/L與鎂濃度1.5 mmol/L之狀態並預期出其反應值MFI0.2為-0.3、磷保留率為100 %，代表結垢情形不易產生，磷酸鹽呈現溶解態，對於後續磷回收為最佳狀態。最差解為當磷濃度4.5 mmol/L、鈣離子濃度2.25 mmol/L與鎂濃度1.5 mmol/L之狀態，預期反應值則為MFI0.2為 3.59、磷保留率為94.8 %，代表有結垢產生，磷酸鹽也發生沉澱反應，造成磷保留率下降，該狀態容易使在前處理時無機物沉澱出顆粒物造成薄膜結垢之現象，產生磷酸鹽保留率不佳。此外，長期薄膜過濾中，與最佳條件比較，最差條件之阻力明顯上升，其中，在薄膜過濾進行中，容易先導致孔堵塞再形成濾餅層，造成TMP迅速上升。在阻力分析中發現最佳條件之孔阻力占比為12 %，最差條件之孔阻力占比為30 %，因此，最主要導致脫水濾液無機性結垢之原因為不可逆結垢。
摘要(英)	Due to the increase in the amount of phosphate mining in recent years, the issue of phosphorus recovery has gradually received attention. The anaerobic digestion process in sewage treatment has high phosphorus and high nitrogen components, but it contains a lot of suspended solids and organic matter, which is easy to make recycling ineffective. Therefore, optimizing the quality of phosphorus recovery by pretreatment is a required procedure for future applications. However, when membrane filtration is used for pretreatment, it is easy to encounter the problem of fouling and scaling, resulting in poor filtration efficiency increasing costs, and reducing effectiveness. In this study, the fouling potential and phosphorus retention rate experiments were carried out using synthetic sludge dewatering filtrate. The batch experiment and response surface methodology were used to explore the optimal condition for the concentration range of the actual wastewater treatment plant, Moreover using long-term membrane filtration experiments to compare and verify the difference in fouling characteristics between the optimal and worst conditions. The water quality analysis of the wastewater from the actual wastewater treatment plant showed that the pH of the sludge dewatering filtrate was 7.9±0.1, the phosphate - phosphorus concentration was 128.1±8.2 mg/L, the ammonium - nitrogen concentration was 771.3±68.1 mg/L, and the total solids concentration was 1,163±80.1 mg/L and TOC was 56.2±10.3 mg/L. The pH of the anaerobic digestion supernatant was 7.6±0.6, the phosphate - phosphorus concentration was 170.7±42.0 mg/L, the ammonium - nitrogen concentration was 871.2±102.2 mg/L, the total solid concentration was 33,193±166.2 mg/L and the COD was 698.9±21.6 mg /L, compared sludge dewatering filtrate to anaerobic digestion supernatant, due to the higher suspended solids and organic matter in the anaerobic digestion supernatant, it is difficult to membrane pretreatment and phosphorus recovery, while the sludge dewatering filtrate contains less suspended solids and still has a higher phosphorus concentration. Therefore, the sludge dewatering filtrate has better recovery potential. In the batch experiment, different pH values and calcium concentrations were used to do MFI0.2 and phosphorus retention experiments. According to the results, higher pH results in higher MFI0.2 and lower phosphorus retention. In pH 6-7, it has lower MFI0.2 and higher phosphorus retention rate, because the pH range of the precipitation reaction is about pH 7.5-12. When the pH is lower than this range, particles are not easily generated. When the pH is 7.5-9, with the increase of pH, The IAP in solution is higher than the Ksp of various phosphate compounds, such as magnesium ammonium phosphate, hydroxyapatite, etc., and the precipitate is generated. This leads to membrane scaling. At the same time, it is found that with the increase of pH and calcium concentration from low to high, MFI0.2, particle size, and possible types of precipitates all increase gradually, while phosphorus retention rate gradually decreases. When the pH is fixed at 7.5 and analyzed by the response surface methodology under phosphate - phosphorus concentration 1.5-4.5 mmol/L (46.46-139.37 mg/L), magnesium ion 0.5-1.5 mmol/L (12.1-36.5 mg/L) and calcium ion 0.75-2.25 mmol/L (30-120 mg/L), the optimal condition is obtained when the concentration of phosphate - phosphorus is 1.5 mmol/L, the concentration of calcium is 0.75 mmol/L and the concentration of magnesium is 1.5 mmol/L, and the reaction value MFI0.2 is expected to be -0.3, the phosphorus retention rate is 100%. It means that the scaling situation is not easy to occur, and the phosphate is in a dissolved state, which is optimal for subsequent phosphorus recovery. The worst condition is that when the phosphate - phosphorus concentration is 4.5 mmol/L, the calcium concentration is 2.25 mmol/L and the magnesium concentration is 1.5 mmol/L, the expected reaction value is MFI0.2 of 3.59 and phosphorus retention rate of 94.8 %, which means membrane scaling. The precipitation reaction causes the phosphorus retention rate to decrease. This state is likely to cause the inorganic compound to precipitate out of particles during pretreatment, cause membrane scaling, and poor phosphorus retention rate. In addition, in the long-term membrane filtration, compared with the optimal conditions, the resistance of the worst conditions increased significantly. Among them, during the membrane filtration process, it is easy to cause the membrane pores to block first and then form the filter cake layer, resulting in a rapid increase in TMP. In the resistance analysis, it was found that the pore-blocking ratio of the best condition was 12%, and the pore-blocking ratio of the worst condition was 30%. Therefore, the main reason for the inorganic scaling of the dewatering filtrate was irreversible scaling.
關鍵字(中)	★ 結垢 ★ pH ★ 脫水濾液 ★ 反應曲面法 ★ 最佳化 ★ 薄膜過濾	關鍵字(英)	★ Scaling ★ pH ★ sludge dewatering filtrate ★ Reaction Surface Method ★ Optimization ★ Membrane Filtration
論文目次	摘要 i Abstract iii 誌謝 vi 目錄 vii 圖目錄 x 表目錄 xiii 第一章 前言 1 1.1研究緣起 1 1.2研究目的 2 第二章 文獻回顧 3 2.1厭氧污泥脫水濾液 3 2.1.1 污泥厭氧消化原理及程序 3 2.1.2厭氧污泥脫水濾液組成及特色 6 2.2薄膜過濾 8 2.2.1薄膜種類 8 2.2.2過濾方式 12 2.2.3薄膜過濾之特性 13 2.3脫水濾液積垢特性 15 2.3.1積垢特性 15 2.3.2脫水濾液積垢特性 18 2.3.3無機性結垢 19 2.4積垢指標 24 2.4.1 污泥密度指數(Silt Density Index, SDI) 24 2.4.2 修正積垢指標(Modified Fouling Index, MFI) 24 2.4.3過飽和指標(Supersaturation index, SI) 26 第三章 研究方法 27 3.1研究流程與步驟 27 3.2實驗材料 29 3.2.1薄膜膜組 29 3.2.2厭氧消化污泥與脫水濾液來源 30 3.3實驗方法與步驟 32 3.3.1 厭氧污泥之脫水濾液基本水質分析 32 3.3.2 合成廢水結垢潛勢批次實驗 32 3.3.3 合成廢水結垢形成試驗 33 3.3.4 薄膜長期過濾實驗 33 3.3.5檢測指標與計算方法 36 3.4反應曲面法 38 3.4.1反應曲面法(Response surface methodology, RSM) 38 3.4.2中央合成設計法(CCD) 39 3.4.3統計分析方法 41 3.4.4最佳化設計 46 3.5實驗設計 49 3.6實驗材料及分析方法 51 3.6.1實驗材料與設備 51 3.6.2分析方法 53 第四章 結果與討論 54 4.1厭氧污泥與脫水濾液基本水質分析 54 4.1.1水質基本分析 54 4.2無機物結垢分析探討 58 4.2.1合成脫水濾液在不同pH與Ca2+條件下對結垢之影響 58 4.2.2合成脫水濾液在不同pH條件下對磷保留率之影響 60 4.2.3合成脫水濾液在不同pH條件下之粒徑分布 66 4.3合成脫水濾液反應曲面法最佳條件探討 73 4.3.1合成脫水濾液反應曲面法分析－MFI0.2與磷保留率迴歸分析 75 4.3.2合成脫水濾液反應曲面法分析－MFI0.2與磷保留率最佳化分析 87 4.4薄膜長期過濾實驗 89 4.4.1薄膜長期過濾實驗之過濾情形 90 4.4.2薄膜長期過濾實驗之阻力 95 第五章 結論與建議 100 5.1結論 100 5.2建議 102 參考文獻 103
參考文獻	Abeywardena, M. R., Elkaduwe, R. K. W. H. M. K., Karunarathne, D. G. G. P., Pitawala, H. M. T. G. A., Rajapakse, R. M. G., Manipura, A., & Mantilaka, M. M. M. G. P. G. (2020). Surfactant assisted synthesis of precipitated calcium carbonate nanoparticles using dolomite: Effect of pH on morphology and particle size. Advanced Powder Technology, 31(1), 269-278. doi:10.1016/j.apt.2019.10.018 Ahn, W.-Y., Kalinichev, A. G., & Clark, M. M. (2008). Effects of background cations on the fouling of polyethersulfone membranes by natural organic matter: Experimental and molecular modeling study. Journal of Membrane Science, 309(1-2), 128-140. doi:10.1016/j.memsci.2007.10.023 Al-Gebory, L., & Mengüç, M. P. (2018). The effect of pH on particle agglomeration and optical properties of nanoparticle suspensions. Journal of Quantitative Spectroscopy and Radiative Transfer, 219, 46-60. doi:10.1016/j.jqsrt.2018.07.020 Al-Juboori, R. A., & Yusaf, T. (2012). Biofouling in RO system: Mechanisms, monitoring and controlling. Desalination, 302, 1-23. doi:10.1016/j.desal.2012.06.016 Al‐Qasas, N., Rohani, S. J. S. s., & technology. (2005). Synthesis of pure hydroxyapatite and the effect of synthesis conditions on its yield, crystallinity, morphology and mean particle size. 40(15), 3187-3224. Alhadidi, A., Kemperman, A. J. B., Blankert, B., Schippers, J. C., Wessling, M., & van der Meer, W. G. J. (2011). Silt Density Index and Modified Fouling Index relation, and effect of pressure, temperature and membrane resistance. Desalination, 273(1), 48-56. doi:10.1016/j.desal.2010.11.031 Alhadidi, A., Kemperman, A. J. B., Schippers, J. C., Wessling, M., & van der Meer, W. G. J. (2011). The influence of membrane properties on the Silt Density Index. Journal of Membrane Science, 384(1-2), 205-218. doi:10.1016/j.memsci.2011.09.028 Appels, L., Baeyens, J., Degrève, J., & Dewil, R. (2008). Principles and potential of the anaerobic digestion of waste-activated sludge. Progress in Energy and Combustion Science, 34(6), 755-781. doi:10.1016/j.pecs.2008.06.002 Arcas-Pilz, V., Rufi-Salis, M., Parada, F., Petit-Boix, A., Gabarrell, X., & Villalba, G. (2021). Recovered phosphorus for a more resilient urban agriculture: Assessment of the fertilizer potential of struvite in hydroponics. Sci Total Environ, 799, 149424. doi:10.1016/j.scitotenv.2021.149424 Blocher, C., Niewersch, C., & Melin, T. (2012). Phosphorus recovery from sewage sludge with a hybrid process of low pressure wet oxidation and nanofiltration. Water Res, 46(6), 2009-2019. doi:10.1016/j.watres.2012.01.022 Cerqueira, U., Bezerra, M. A., Ferreira, S. L. C., de Jesus Araujo, R., da Silva, B. N., & Novaes, C. G. (2021). Doehlert design in the optimization of procedures aiming food analysis - A review. Food Chem, 364, 130429. doi:10.1016/j.foodchem.2021.130429 Chuang, S. H., Chang, W. C., Chang, M. C., & Sung, M. A. (2009). The effects of soluble organic matters on membrane fouling index. Bioresour Technol, 100(5), 1875-1877. doi:10.1016/j.biortech.2008.09.054 Cichy, B., Kuzdzal, E., & Krzton, H. (2019). Phosphorus recovery from acidic wastewater by hydroxyapatite precipitation. J Environ Manage, 232, 421-427. doi:10.1016/j.jenvman.2018.11.072 Cojocaru, C., & Zakrzewska-Trznadel, G. (2007). Response surface modeling and optimization of copper removal from aqua solutions using polymer assisted ultrafiltration. Journal of Membrane Science, 298(1-2), 56-70. doi:10.1016/j.memsci.2007.04.001 Cordell, D., Drangert, J.-O., & White, S. (2009). The story of phosphorus: Global food security and food for thought. Global Environmental Change, 19(2), 292-305. doi:10.1016/j.gloenvcha.2008.10.009 Cui, Z. F., Jiang, Y., & Field, R. W. (2010). Fundamentals of Pressure-Driven Membrane Separation Processes. In Membrane Technology (pp. 1-18). Cydzik-Kwiatkowska, A., & Zielińska, M. (2020). Waste-organics supported treatment of nitrogen-rich digester supernatant. Journal of Water Process Engineering, 37. doi:10.1016/j.jwpe.2020.101385 Dahdouh, L., Delalonde, M., Ricci, J., Servent, A., Dornier, M., & Wisniewski, C. (2016). Size-cartography of orange juices foulant particles: Contribution to a better control of fouling during microfiltration. Journal of Membrane Science, 509, 164-172. doi:10.1016/j.memsci.2016.01.052 Dersoir, B., Schofield, A. B., Robert de Saint Vincent, M., & Tabuteau, H. (2019). Dynamics of pore fouling by colloidal particles at the particle level. Journal of Membrane Science, 573, 411-424. doi:10.1016/j.memsci.2018.12.025 Dorofeev, A. G., Nikolaev, Y. A., Kozlov, M. N., Kevbrina, M. V., Agarev, A. M., Kallistova, A. Y., & Pimenov, N. V. (2017). Modeling of anammox process with the biowin software suite. Applied Biochemistry and Microbiology, 53(1), 78-84. doi:10.1134/s0003683817010100 Du, X., Zhang, K., Yang, H., Li, K., Liu, X., Wang, Z., . . . Liang, H. (2019). The relationship between size-segregated particles migration phenomenon and combined membrane fouling in ultrafiltration processes: The significance of shear stress. Journal of the Taiwan Institute of Chemical Engineers, 96, 45-52. doi:10.1016/j.jtice.2018.11.016 FOLEY, G. ( 2013). Membrane Filtration. Gao, Y., Chen, D., Weavers, L. K., & Walker, H. W. (2012). Ultrasonic control of UF membrane fouling by natural waters: Effects of calcium, pH, and fractionated natural organic matter. Journal of Membrane Science, 401-402, 232-240. doi:10.1016/j.memsci.2012.02.009 Gerardo, M. L., Zacharof, M. P., & Lovitt, R. W. (2013). Strategies for the recovery of nutrients and metals from anaerobically digested dairy farm sludge using cross-flow microfiltration. Water Res, 47(14), 4833-4842. doi:10.1016/j.watres.2013.04.019 Guo, W., Ngo, H. H., & Li, J. (2012). A mini-review on membrane fouling. Bioresour Technol, 122, 27-34. doi:10.1016/j.biortech.2012.04.089 Gupta, K., & Chellam, S. (2020). Contributions of surface and pore deposition to (ir)reversible fouling during constant flux microfiltration of secondary municipal wastewater effluent. Journal of Membrane Science, 610. doi:10.1016/j.memsci.2020.118231 Hallas, J., Mackowiak, C., Wilkie, A., & Harris, W. (2019). Struvite Phosphorus Recovery from Aerobically Digested Municipal Wastewater. Sustainability, 11(2). doi:10.3390/su11020376 Hinsinger, P. (2001). Bioavailability of soil inorganic P in the rhizosphere as affected by root-induced chemical changes: a review. Kluwer Academic Publishers. Huang, H., Liu, J., & Ding, L. (2015). Recovery of phosphate and ammonia nitrogen from the anaerobic digestion supernatant of activated sludge by chemical precipitation. Journal of Cleaner Production, 102, 437-446. doi:10.1016/j.jclepro.2015.04.117 Jiang, S., Li, Y., & Ladewig, B. P. (2017). A review of reverse osmosis membrane fouling and control strategies. Sci Total Environ, 595, 567-583. doi:10.1016/j.scitotenv.2017.03.235 Jowitt, S. M., Mudd, G. M., & Thompson, J. F. H. (2020). Future availability of non-renewable metal resources and the influence of environmental, social, and governance conflicts on metal production. Communications Earth & Environment, 1(1). doi:10.1038/s43247-020-0011-0 Jowitt, S. M., Mudd, G. M., Thompson, J. F. J. C. E., & Environment. (2020). Future availability of non-renewable metal resources and the influence of environmental, social, and governance conflicts on metal production. 1(1), 1-8. Jun, D., Kim, Y., Hafeznezami, S., Yoo, K., Hoek, E. M. V., & Kim, J. (2017). Biologically induced mineralization in anaerobic membrane bioreactors: Assessment of membrane scaling mechanisms in a long-term pilot study. Journal of Membrane Science, 543, 342-350. doi:10.1016/j.memsci.2017.08.025 Jupp, A. R., Beijer, S., Narain, G. C., Schipper, W., & Slootweg, J. C. J. C. S. R. (2021). Phosphorus recovery and recycling–closing the loop. 50(1), 87-101. Karimifard, S., & Alavi Moghaddam, M. R. (2018). Application of response surface methodology in physicochemical removal of dyes from wastewater: A critical review. Sci Total Environ, 640-641, 772-797. doi:10.1016/j.scitotenv.2018.05.355 Kim, S., Lee, D. W., & Cho, J. (2016). Application of direct contact membrane distillation process to treat anaerobic digestate. Journal of Membrane Science, 511, 20-28. doi:10.1016/j.memsci.2016.03.038 Lahav, O., Telzhensky, M., Zewuhn, A., Gendel, Y., Gerth, J., Calmano, W., & Birnhack, L. (2013). Struvite recovery from municipal-wastewater sludge centrifuge supernatant using seawater NF concentrate as a cheap Mg(II) source. Separation and Purification Technology, 108, 103-110. doi:10.1016/j.seppur.2013.02.002 Le, V.-G., Vo, D.-V. N., Nguyen, N.-H., Shih, Y.-J., Vu, C.-T., Liao, C.-H., & Huang, Y.-H. (2021). Struvite recovery from swine wastewater using fluidized-bed homogeneous granulation process. Journal of Environmental Chemical Engineering, 9(3). doi:10.1016/j.jece.2020.105019 Lew, B., Phalah, S., Sheindorf, C., Kummel, M., Rebhun, M., & Lahav, O. (2010). Favorable Operating Conditions for Obtaining High-Value Struvite Product from Sludge Dewatering Filtrate. Environmental Engineering Science, 27(9), 733-741. doi:10.1089/ees.2009.0279 Lewis, W. J. T., Mattsson, T., Chew, Y. M. J., & Bird, M. R. (2017). Investigation of cake fouling and pore blocking phenomena using fluid dynamic gauging and critical flux models. Journal of Membrane Science, 533, 38-47. doi:10.1016/j.memsci.2017.03.020 Li, X., Shen, S., Xu, Y., Guo, T., Dai, H., & Lu, X. (2021). Application of membrane separation processes in phosphorus recovery: A review. Sci Total Environ, 767, 144346. doi:10.1016/j.scitotenv.2020.144346 Lin, H., Chen, Y., Shen, N., Deng, Y., Yan, W., Ruhyadi, R., & Wang, G. (2020). Effects of individual volatile fatty acids (VFAs) on phosphorus recovery by magnesium ammonium phosphate. Environ Pollut, 261, 114212. doi:10.1016/j.envpol.2020.114212 Lin, T., Lu, Z., & Chen, W. (2015). Interaction mechanisms of humic acid combined with calcium ions on membrane fouling at different conditions in an ultrafiltration system. Desalination, 357, 26-35. doi:10.1016/j.desal.2014.11.007 Liu, X., & Wang, J. (2019). Impact of calcium on struvite crystallization in the wastewater and its competition with magnesium. Chemical Engineering Journal, 378. doi:10.1016/j.cej.2019.122121 Liu, Y.-J., & Sun, D. D. (2012). Particles size-associated membrane fouling in microfiltration of denitrifying granules supernatant. Chemical Engineering Journal, 181-182, 494-500. doi:10.1016/j.cej.2011.12.009 Loria, K. G., Aragón, J. C., Torregiani, S. M., Pilosof, A. M. R., & Farías, M. E. (2018). Flow properties of caseinomacropeptide aqueous solutions: Effect of particle size distribution, concentration, pH and temperature. Lwt, 93, 243-248. doi:10.1016/j.lwt.2018.03.050 Macha, I., Boonyang, U., Cazalbou, S., Ben-Nissan, B., Charvillat, C., Oktar, F., & Grossin, D. (2015). Comparative study of Coral Conversion, Part 2: Microstructural evolution of calcium phosphate. JOUrnal of the Australian Ceramic Society, 51, 149-159. Marti, N., Ferrer, J., Seco, A., & Bouzas, A. (2008). Optimisation of sludge line management to enhance phosphorus recovery in WWTP. Water Res, 42(18), 4609-4618. doi:10.1016/j.watres.2008.08.012 Metzger, U., Le-Clech, P., Stuetz, R. M., Frimmel, F. H., & Chen, V. (2007). Characterisation of polymeric fouling in membrane bioreactors and the effect of different filtration modes. Journal of Membrane Science, 301(1-2), 180-189. doi:10.1016/j.memsci.2007.06.016 Pap, S., Stankovits, G. J., Gyalai-Korpos, M., Mako, M., Erdelyi, I., & Turk Sekulic, M. (2021). Biochar application in organics and ultra-violet quenching substances removal from sludge dewatering leachate for algae production. J Environ Manage, 298, 113446. doi:10.1016/j.jenvman.2021.113446 Park, C., Kim, H., Hong, S., & Choi, S.-I. (2006). Variation and prediction of membrane fouling index under various feed water characteristics. Journal of Membrane Science, 284(1-2), 248-254. doi:10.1016/j.memsci.2006.07.036 Ping, Q., Li, Y., Wu, X., Yang, L., & Wang, L. (2016). Characterization of morphology and component of struvite pellets crystallized from sludge dewatering liquor: Effects of total suspended solid and phosphate concentrations. J Hazard Mater, 310, 261-269. doi:10.1016/j.jhazmat.2016.02.047 Polyakov, Y. S., & Zydney, A. L. (2013). Ultrafiltration membrane performance: Effects of pore blockage/constriction. Journal of Membrane Science, 434, 106-120. doi:10.1016/j.memsci.2013.01.052 Salinas Rodriguez, S. G., Sithole, N., Dhakal, N., Olive, M., Schippers, J. C., & Kennedy, M. D. (2019). Monitoring particulate fouling of North Sea water with SDI and new ASTM MFI0.45 test. Desalination, 454, 10-19. doi:10.1016/j.desal.2018.12.006 Scott, K. J. H. o. i. m. i. t. m. s. r. e. E. A. T. (1995). Introduction to membrane separations. 3-185. Shaddel, S., Grini, T., Andreassen, J.-P., Østerhus, S. W., & Ucar, S. (2020). Crystallization kinetics and growth of struvite crystals by seawater versus magnesium chloride as magnesium source: towards enhancing sustainability and economics of struvite crystallization. Chemosphere, 256, 126968. doi:10.1016/j.chemosphere.2020.126968 Shaddel, S., Ucar, S., Andreassen, J. P., & Osterhus, S. W. (2019). Enhancing efficiency and economics of phosphorus recovery process by customizing the product based on sidestream characteristics - an alternative phosphorus recovery strategy. Water Sci Technol, 79(9), 1777-1789. doi:10.2166/wst.2019.178 Sim, L. N., Chong, T. H., Taheri, A. H., Sim, S. T. V., Lai, L., Krantz, W. B., & Fane, A. G. (2018). A review of fouling indices and monitoring techniques for reverse osmosis. Desalination, 434, 169-188. doi:10.1016/j.desal.2017.12.009 Sim, L. N., Ye, Y., Chen, V., & Fane, A. G. (2010). Crossflow Sampler Modified Fouling Index Ultrafiltration (CFS-MFIUF)—An alternative Fouling Index. Journal of Membrane Science, 360(1-2), 174-184. doi:10.1016/j.memsci.2010.05.010 Simoes, F., Colston, R., Rosa-Fernandes, C., Vale, P., Stephenson, T., & Soares, A. (2020). Predicting the potential of sludge dewatering liquors to recover nutrients as struvite biominerals. Environmental Science and Ecotechnology, 3. doi:10.1016/j.ese.2020.100052 Siobhan F.E. Boerlage , M. D. K., Melvyn R. Dickson ,, & Dima E.Y. El-Hodali , J. C. S. (2002). The modified fouling index using ultrafiltration membranes(MFI-UF): characterisation, filtration mechanisms andproposed reference membrane. Journal of Membrane Science, 197, 1-21. Taheri, A. H., Sim, L. N., Haur, C. T., Akhondi, E., & Fane, A. G. (2013). The fouling potential of colloidal silica and humic acid and their mixtures. Journal of Membrane Science, 433, 112-120. doi:10.1016/j.memsci.2013.01.034 Tarragó, E., Sciarria, T. P., Ruscalleda, M., Colprim, J., Balaguer, M. D., Adani, F., & Puig, S. (2018). Effect of suspended solids and its role on struvite formation from digested manure. Journal of Chemical Technology & Biotechnology, 93(9), 2758-2765. doi:10.1002/jctb.5651 Tourbin, M., Brouillet, F., Galey, B., Rouquet, N., Gras, P., Abi Chebel, N., . . . Frances, C. (2020). Agglomeration of stoichiometric hydroxyapatite: Impact on particle size distribution and purity in the precipitation and maturation steps. Powder Technology, 360, 977-988. doi:10.1016/j.powtec.2019.10.050 van Rensburg, P., Musvoto, E. V., Wentzel, M. C., & Ekama, G. A. (2003). Modelling multiple mineral precipitation in anaerobic digester liquor. Water Research, 37(13), 3087-3097. doi:10.1016/s0043-1354(03)00173-8 VERDOUW, J. C. S. A. J. (1980). The modified fouling index, a method of determining the fouling characteristics of water. Desalination, 32, 137-148. Wang, R., Liang, D., Liu, X., Fan, W., Meng, S., & Cai, W. (2020). Effect of magnesium ion on polysaccharide fouling. Chemical Engineering Journal, 379. doi:10.1016/j.cej.2019.122351 Wang, Z., Ma, J., Tang, C. Y., Kimura, K., Wang, Q., & Han, X. (2014). Membrane cleaning in membrane bioreactors: A review. Journal of Membrane Science, 468, 276-307. doi:10.1016/j.memsci.2014.05.060 Wu, J., He, C., Jiang, X., & Zhang, M. (2011). Modeling of the submerged membrane bioreactor fouling by the combined pore constriction, pore blockage and cake formation mechanisms. Desalination, 279(1-3), 127-134. doi:10.1016/j.desal.2011.05.069 Wu, Z., Qiao, W., Liu, Y., Yao, J., Gu, C., Zheng, X., & Dong, R. (2022). Contribution of chemical precipitation to the membrane fouling in a high-solids type anaerobic membrane bioreactor treating OFMSW leachate. Journal of Membrane Science, 647. doi:10.1016/j.memsci.2022.120298 Yan, Z., Liu, K., Yu, H., Liang, H., Xie, B., Li, G., . . . van der Bruggen, B. (2019). Treatment of anaerobic digestion effluent using membrane distillation: Effects of feed acidification on pollutant removal, nutrient concentration and membrane fouling. Desalination, 449, 6-15. doi:10.1016/j.desal.2018.10.011 Yao, M., Zhang, K., & Cui, L. (2010). Characterization of protein–polysaccharide ratios on membrane fouling. Desalination, 259(1-3), 11-16. doi:10.1016/j.desal.2010.04.049 Ye, X., Ye, Z.-L., Lou, Y., Pan, S., Wang, X., Wang, M. K., & Chen, S. (2016). A comprehensive understanding of saturation index and upflow velocity in a pilot-scale fluidized bed reactor for struvite recovery from swine wastewater. Powder Technology, 295, 16-26. doi:10.1016/j.powtec.2016.03.022 Zacharof, M.-P., & Lovitt, R. W. (2014). The filtration characteristics of anaerobic digester effluents employing cross flow ceramic membrane microfiltration for nutrient recovery. Desalination, 341, 27-37. doi:10.1016/j.desal.2014.02.034 Zacharof, M.-P., Mandale, S. J., Oatley-Radcliffe, D., & Lovitt, R. W. (2019). Nutrient recovery and fractionation of anaerobic digester effluents employing pilot scale membrane technology. Journal of Water Process Engineering, 31. doi:10.1016/j.jwpe.2019.100846 Zhang, M., Lin, H., Shen, L., Liao, B.-Q., Wu, X., & Li, R. (2017). Effect of calcium ions on fouling properties of alginate solution and its mechanisms. Journal of Membrane Science, 525, 320-329. doi:10.1016/j.memsci.2016.12.006 行政院環保署統計室(2020)。廢污水產生量及排放量。 行政院環境保護署環境保護人員訓練所廢(污)水處理專責人員訓練教材(2020)。廢水處理單元操作維護。 李靖儀 (2011)。防電磁波干擾製程參數最佳化之研究 (碩士)。東海大學。 林李旺(2018)。突破品質水準實驗設計與田口方法之實務應用。全華圖書出版社。 桃園市政府水務局(2019)。桃園水資源回收中心。 張維中 (2015)。公共污水處理廠污泥厭氧消化效能評估-超音波水解及質量平衡分析。 莊順興(2014)。薄膜技術與積垢指標。Retrieved from https://www.edf.org.tw/Documents/01.%E8%8E%8A%E9%A0%86%E8%88%88%20%E6%95%99%E6%8E%88-%E6%B0%B4%E5%9B%9E%E6%94%B6%E5%86%8D%E5%88%A9%E7%94%A8%E6%8A%80%E8%A1%93.pdf 游雅淳 (2012)。垂直式與掃流式淤泥積垢指標之比較研究 (碩士)。朝陽科技大學。 黃日輝 (2008)。TFT-LCD 業鋁蝕刻製程含磷廢水最佳可行控制技術評估。 黃明樟 (2001)。薄膜程序處理染整業放流水回收再利用之研究 (碩士)。淡江大學。 黃欣栩(2021)。108~109年度全國公共污水處理廠營建評鑑成果分享。 經濟部工業局(2005)。廢水污泥減量技術手冊。 葉怡成(2006)。實驗計畫法一 製程與產品最佳化。五南圖書出版股份有限公司。 鄭東文、林智偉 (2014)。薄膜過濾家族。科學發展。Retrieved from https://ejournal.stpi.narl.org.tw/sd/download?source=10308-06.pdf&vlId=FFBA62B7-FAEB-4694-B973-2590C23D8CA3&nd=1&ds=1 鍾泰華 (2016)。以反應曲面法進行U型引伸彎曲之最佳化分析(碩士)。國立中央大學。
指導教授	莊順興	審核日期	2022-9-13
推文	facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu
網路書籤	Google bookmarks   del.icio.us   hemidemi   myshare