English  |  正體中文  |  简体中文  |  全文筆數/總筆數 : 64745/64745 (100%)
造訪人次 : 20508172      線上人數 : 286
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜尋範圍 查詢小技巧:
  • 您可在西文檢索詞彙前後加上"雙引號",以獲取較精準的檢索結果
  • 若欲以作者姓名搜尋,建議至進階搜尋限定作者欄位,可獲得較完整資料
  • 進階搜尋

    請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/2811

    題名: 旋塗時接觸角變化研究;Study on Variation of Dynamic Contact Angle during Spin Coating
    作者: 林耕葆;Geng-Bao Lin
    貢獻者: 機械工程研究所
    關鍵詞: 動態接觸角;旋塗;spin coating;dynamic contact angle
    日期: 2006-06-27
    上傳時間: 2009-09-21 11:56:45 (UTC+8)
    出版者: 國立中央大學圖書館
    摘要: 將液體利用旋轉塗佈方式塗佈到固體表面的過程中,會產生表面張力、黏滯力及離心力三者之間的相互關係。本文利用四種黏度的矽油於五種轉速下的動態接觸角與時間、動態接觸角與毛細管數( Ca )、動態接觸角與邦得數( Bo )、動態接觸角與雷諾數( Re ) 及動態接觸角與韋伯數( We )等關係,解釋表面張力、黏滯力及離心力三者對旋轉塗佈時之影響。針對同樣黏度之矽油,不同的旋轉速度,可看出動態接觸角度隨時間的變化有呈現一震盪的現象。此現象可分為三階段:發展期、峰值期、遞減期。發展期階段動態接觸角角度隨實驗時間增加而逐漸變大。峰值期階段動態接觸角度會隨實驗時間增加而達一最大值。遞減期階段動態接觸角角度從最大值降至一穩定值後持續至下一週期。加入無因次參數以幫助對於新現象發生的原因探討與了解。利用所得結果,進一步應用於液滴旋塗時臨界半徑的產生現象分析,最終能得一機制以預測或控制臨界半徑產生時機。 Utilize the liquid the rotatory coating way coating to in solid and superficial course, will produce the interrelation among surface tension, viscid strength and centrifugal three. This text utilizes four kinds viscosity of silicon oil under five kinds of rotational speed to get the relation between dynamical contact angle and time, capillary number (Ca), Bound number (Bo)‚Reynolds number (Re) and Weber number (We), to explain surface tension , viscid strength and centrifugal three to the influence while rotating coatings. To the silicon oil of the same viscosity, different speeds of rotation, can find out that the phenomenon of a shock has appeared with the change of time in the dynamic contact angle. This phenomenon can be divided into three stages: Develop one, peak period and decreasing progressively period. At develop stage the dynamic contact angle will increase with time. Peak period stage the dynamic contact angle will increase with time up to a maximum angle. Decreasing progressively period the dynamic contact will decrease from maximum angle to a stability angle and then last until the next cycle. We are using some dimensionless numbers to help discussion the cause reasons and to new understanding that phenomenon take place. Utilize the result of incomes, use the formulation phenomenon analysis of the critical radius when the drop is fastened and scribbled further, can must one mechanism in order to predict or control critical radius, happen time.
    顯示於類別:[機械工程研究所] 博碩士論文


    檔案 大小格式瀏覽次數


    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 回饋  - 隱私權政策聲明