以懸浮聚合法製備潤滑油微膠囊材料;microcapsulation of lubricating oil by suspension polymerization

NCU Institutional Repository > 工學院 > 化學工程與材料工程研究所 > 博碩士論文 > Item 987654321/53683

jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/53683

题名:	以懸浮聚合法製備潤滑油微膠囊材料;microcapsulation of lubricating oil by suspension polymerization
作者:	李浚瑀;Li,Jyun-yu
贡献者:	化學工程與材料工程研究所
关键词:	微膠囊;懸浮聚合法;潤滑油;苯乙烯;甲基丙烯酸甲酯;microcapsules;suspension polymerization;styrene;methyl methacrylate;lubricating oil
日期:	2012-06-20
上传时间:	2012-09-11 18:10:57 (UTC+8)
出版者:	國立中央大學
摘要:	本論文利用懸浮聚合法製備電鍍共沉積用之潤滑油微膠囊，將單體、交聯劑、潤滑油和起始劑混合，加入含有穩定劑PVA 的水溶液中，以乳化均質機攪拌均勻後進行懸浮聚合反應，進而製備潤滑油微膠囊材料。本實驗使用的單體為甲基丙烯酸甲酯(MMA)、苯乙烯(St)，交聯劑為二甲基丙烯酸乙二醇酯(EGDMA)和起始劑偶氮二異丁腈(AIBN)。本研究探討穩定劑濃度、單體比例、起始劑添加量、交聯劑濃度、均質機轉速、反應時間和潤滑油的添加量等不同條件對微膠囊材料的整體轉化率、潤滑油含量、潤滑油產率、高分子產率、包覆效率及外觀的影響，並利用熱重損失分析儀(TGA)、傅立葉轉換紅外線光譜儀(FTIR)、掃描式電子顯微鏡(SEM)和動態光散射儀(DLS)進行分析。從本研究中可得知，當穩定劑PVA 濃度為0.1wt%時有最佳微膠囊外觀，St 的單體比例為50%以上時較適合作為微膠囊殼層，起始劑添加量和交聯劑濃度的上升有助於提升整體轉化率和高分子產率，反應時間為6 和8 小時有較佳的潤滑油含量和產率。本研究可製備出潤滑油含量為63.4%，粒徑範圍約為150~350nm，以及整體轉化率為71.2%之潤滑油微膠囊材料。Microcapsulation of lubricating oil for electrolytic co-deposition has beendeveloped by suspension polymerization. Monomers, cross-linking agent,lubricating oil, and initiator were mixed and then added to the water phaseincluding stabilizer, PVA. After that, the solution was homogenized andproceeded to suspension polymerization at 70oC. Methyl methacrylate (MMA)and styrene (St) were used as the monomers. Ethylene Glycol Dimethacrylate(EGDMA) was used as cross-linking agent. Azobisisobutyronitrile (AIBN) wasused as initiator.In this study, different parameters, the concentrations of stabilizer, initiator,cross-linking agent, and lubricating oil, homogenized speed, reaction time, andaddition of lubricating oil were discussed. Thermo gravimetric Analysis (TGA),Scanning Electron Microscope (SEM) Fourier-Transform Infrared Spectrometer(FTIR), Dynamic light scattering (DLS) were used to determine thecharacterization of the microcapsules.The results showed that the morphology of microcapsules could beimproved by adding 0.1wt% of stabilizer. The weight fraction of St in monomersmore than or equal to 50% was more suitable to be the shell materials. As theamount of initiator and cross-linking agent increased, the total conversion andpolymer yield would increase. When reaction time was 6 or 8 hours, there arebetter lubricating oil content and yield.The best results of microcapsules showed that the lubricating oil content is63.4%, the range of particle size is from 150 to 350nm, and the total conversion is 71.2%.
显示于类别:	[化學工程與材料工程研究所] 博碩士論文

文件中的档案:

档案	描述	大小	格式	浏览次数
index.html		0Kb	HTML	525	检视/开启

在NCUIR中所有的数据项都受到原著作权保护.

社群 sharing

数据加载中.....