中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/5704
English  |  正體中文  |  简体中文  |  全文笔数/总笔数 : 80990/80990 (100%)
造访人次 : 42142706      在线人数 : 1235
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜寻范围 查询小技巧:
  • 您可在西文检索词汇前后加上"双引号",以获取较精准的检索结果
  • 若欲以作者姓名搜寻,建议至进阶搜寻限定作者字段,可获得较完整数据
  • 进阶搜寻


    jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/5704


    题名: 非線性破壞準則之臨界楔模型;Critical taper model with a nonlinear failure criterion
    作者: 楊哲銘;Che-ming Yang
    贡献者: 應用地質研究所
    关键词: 臨界楔模型;破壞準則;地質強度指標;褶皺逆衝帶;增積岩楔;Accretionary wedge.;Fold-and-thrust belt;Geological strength index;Hoek and Brown failure criterion;Critical taper model
    日期: 2009-06-08
    上传时间: 2009-09-22 10:00:06 (UTC+8)
    出版者: 國立中央大學圖書館
    摘要: 由臨界楔形體模型可得楔形體及其基底滑脫面之強度與楔形體形貌之關聯性,根據臨界楔之臨界角,即可反衍楔形體與基底滑脫面之強度參數。本研究將非線性Hoek and Brown破壞準則引入臨界楔模型中,使楔形體強度遵守非線性準則,因此,臨界角將隨楔形體厚度變化而變化。研究結果發現,楔形體強度隨楔形體厚度增加而下降,且臨界角將隨之增大,但增加幅度將隨厚度增加逐漸趨緩。本研究藉由台灣三個褶皺逆衝帶剖面進行模型驗證,經由輸入合理參數值以及計算所得之臨界角,結果顯示模型計算與剖面觀察相符。利用參數敏感性分析得知,強度參數中以地質強度指標、基底滑脫面摩擦係數與基底滑脫面孔隙水壓比對本模型之影響程度較明顯。研究結果顯示,本文建議的非線性Hoek and Brown破壞準則之臨界楔模型,除了可考慮臨界楔厚度影響之外,亦可根據野外調查所得之岩體強度指標,合理的推估楔形體之強度,免除原臨界楔模型決定岩體抗剪摩擦角之困擾。 This study incorporates the nonlinear Hoek and Brown failure criterion into the critical taper model to evaluate the variation of the taper angle of thrust belt with changes of wedge thickness. From collected wedge profile found wedge geometry about three types of morphology were fixed angle, convex upward and concave upward. Because the lateral pore pressure changes at the wedge and the detachment, and formation strength (GSI) change at the wedge, as well as effect of non-linear wedge strength. The wedge strength will decrease with the increasing of wedge thickness. Accordingly, the taper angle increases with the increasing of wedge thickness. Based on the parameter study, the basal coefficient of friction, the basal Hubbert-Rubey pore-fluid pressure ratio on the detachment fault and the Geological Strength Index of the wedge dominate the relation between wedge thickness and taper angle. Therefore, the nonlinearity of wedge strength should be considered for evaluating the mechanical characteristics of thrust belt wedge.
    显示于类别:[應用地質研究所] 博碩士論文

    文件中的档案:

    档案 大小格式浏览次数


    在NCUIR中所有的数据项都受到原著作权保护.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 隱私權政策聲明