中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/65928
English  |  正體中文  |  简体中文  |  全文笔数/总笔数 : 69937/69937 (100%)
造访人次 : 23033198      在线人数 : 432
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜寻范围 查询小技巧:
  • 您可在西文检索词汇前后加上"双引号",以获取较精准的检索结果
  • 若欲以作者姓名搜寻,建议至进阶搜寻限定作者字段,可获得较完整数据
  • 进阶搜寻


    jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/65928


    题名: 超塑5083與非超塑5052鋁合金氣壓成形性比較;Superplasticity Effect Demonstrated by Gas Forming Superplastic 5083 and non-Superplastic 5052 Aluminum Alloy
    作者: 翁正諴;Weng,‎Cheng-hsien
    贡献者: 機械工程學系
    关键词: 超塑成形;整流罩;superplastic forming;Fairing Cover
    日期: 2014-07-16
    上传时间: 2014-10-15 17:18:22 (UTC+8)
    出版者: 國立中央大學
    摘要: 本論文以超塑成形(SuperplasticForming,SPF)之工法應用於飛機製造業所使用之鋁合金蒙皮零件”機翼前緣整流罩(Fairing Cover)”為研究方向,一般超塑成形多以平鈑進行氣吹且成形輪廓都以對稱形狀、深寬比較小為主,複雜曲面及不對稱工件則較少有。因此針對機翼前緣整流罩所使用之模具為複雜曲面且深寬比較大及兩側的V型端深度相對於中間鞍部要來的深,在鈑片進行預折彎時,其材料內部的輪廓變化也相當大。最後在成形結果中產生了皺褶現象,而皺褶的位置剛好顯現在產品零件的裁切線(Ending Opposite Position,E.O.P.)上,針對此一問題會有下列幾項來進行改善:吹製不同條件P-T曲線、不同的材料厚度(AA5052、SP5083)、減少V型端深度(以附加墊塊減少模具成本的花費)等進行研究,以此完成最佳的吹製成形零件(即整流罩)。;This thesis focuses on using superplastic forming to manufacture the aluminum "Airplane Fairing Cover" used on an actual commercial airliner. General superplastic forming usually uses flat sheet to produce symmetrical and less depth-width shape contour, however, the complicated and non-symmetrical work pieces are rarely produced by using superplastic forming. The sheet contour deform is large when flat sheet do the bending process, because fairing cover forming mold have complex shape, high aspect-ratio and the mold V-shape is deeper than middle saddle zone.
    Finally, wrinkle phenomenon occur in the forming results, and it is occur inside the cutting line area (Ending Opposite Position, EOP) of the product. In order to get the best forming result (i.e. fairing cover) and solve this problem, several improvement are perform, such as: blow with different P-T curve conditions, different material and material thickness usage (AA5052 and SP5083) and reduce the depth of V-side by modify mold (by add pads to reduce the mold cost).
    显示于类别:[機械工程研究所] 博碩士論文

    文件中的档案:

    档案 描述 大小格式浏览次数
    index.html0KbHTML308检视/开启


    在NCUIR中所有的数据项都受到原著作权保护.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 回馈  - 隱私權政策聲明