中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/79664
English  |  正體中文  |  简体中文  |  全文筆數/總筆數 : 78852/78852 (100%)
造訪人次 : 37835816      線上人數 : 3462
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜尋範圍 查詢小技巧:
  • 您可在西文檢索詞彙前後加上"雙引號",以獲取較精準的檢索結果
  • 若欲以作者姓名搜尋,建議至進階搜尋限定作者欄位,可獲得較完整資料
  • 進階搜尋


    請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/79664


    題名: 液晶顯示器的窄邊框之研究;Study on the narrow bezel of liquid crystal display
    作者: 陳柏佑;Chen, Po-Yu
    貢獻者: 機械工程學系在職專班
    關鍵詞: 顯示器;複合稜鏡;幾何光學原理
    日期: 2019-01-23
    上傳時間: 2019-04-02 15:11:35 (UTC+8)
    出版者: 國立中央大學
    摘要: 本論文主要探討在顯示器上方增加複合稜鏡,利用稜鏡將部分的光線導引將畫面邊緣部分些微拉伸至邊框部分,來發揮遮蓋住部分的邊框,達成邊框窄化的視覺效果。第一部分在說明此研究下所有的複合稜鏡反射面的幾何形狀以及全反射面和進光面夾角α的架構,第二部分,我們針對這些架構及條件進行光學軟體的模擬。
    結果顯示,當平面形複合稜鏡α角32°均勻度88.35%、凸面弧形複合稜鏡弧形+R40α角30°均勻度66.87%和凹面弧形複合稜鏡‐R40α角34°均勻度62.58%均勻度為最佳。分析三種複合稜鏡在0°、10°、20°、30°和40°不同角度的相對輝度, 0°~10°平面形複合稜鏡輝度最佳,20°~40°凹面弧形複合稜鏡輝度表現最佳。透過導光板佈點密度由0%提升至15%、密度分布距離導光板邊緣距離約10m左右,模擬結果可以提升平面稜鏡亮度約6%左右以改善全反射面亮度偏低的問題。
    ;This thesis mainly was discussed adding a composite lens on the top of the display module and using the lens to extend the edge portion of the screen to the frame part to achieve a borderless visual effect. In section 1, it was discussed all the shapes of the reflection surface of composite lens and the α angle between the surfaces of reflection and light emitting. In section 2, we processed the optical simulation based on all the structures.
    The results show that the uniformity is 88.35% as α angle of the planar composite lens is 32°, the uniformity is 66.87% as α angle of the R40 convex curved composite lens is 30°, and the uniformity is 62.58% as α angle of the R40 concave curved composite lens is 34°. In the conditions, the uniformity of the screen is the best. The three kinds of the composite lens were observed at the viewing angle from 0° to 40°. The planar composite lens brightness was the best at 0° to 10°, and the concave curved composite lens brightness performed the best at 20° to 40°. The dot density of the light guide plate is increased from 0% to 15%, and the distance of pattern distribution is about 10mm from the side of the light guide plate. The simulation result shows the brightness of the planar lens can increase by about 6%.
    顯示於類別:[Executive Master of Mechanical Engineering] Electronic Thesis & Dissertation

    文件中的檔案:

    檔案 描述 大小格式瀏覽次數
    index.html0KbHTML271檢視/開啟


    在NCUIR中所有的資料項目都受到原著作權保護.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 隱私權政策聲明