薄膜生物反應器積垢影響因子之研究-以新竹園區污水廠為例

NCU Institutional Repository > 工學院 > 環境工程研究所碩士在職專班 > 博碩士論文 > Item 987654321/81813

請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/81813

題名:	薄膜生物反應器積垢影響因子之研究-以新竹園區污水廠為例
作者:	鄭楹枚;Mei, Cheng-Ying
貢獻者:	環境工程研究所在職專班
關鍵詞:	薄膜生物反應槽（MBR）;積垢;薄膜滲透性;透膜壓力（TMP）;membrane bioreactor (MBR);fouling;membrane permeability;transmembrane pressure (TMP)
日期:	2019-07-30
上傳時間:	2019-09-03 17:03:54 (UTC+8)
出版者:	國立中央大學
摘要:	摘要為符合最新放流水氨氮管制限值，新竹園區污水處理廠選用薄膜生物反應器(Membrane Bioreactor，MBR)作為功能提升之關鍵處理程序，考量水質特性產生積垢可能影響薄膜使用壽命，故本研究以新竹園區污水處理廠廢(污)水為研究標的，探討可能影響薄膜積垢之因子，具體研究內容包含彙整近3年污水處理廠進、放流水質，分析廢水水質特性；利用與實廠程序相同之模廠進行試驗，調整各項參數以了解各操作因子對薄膜積垢之影響。　　研究結果顯示，污水廠進、放流水質數據，經計算藍氏飽和指數(Langelier Saturation Index, LSI)及萊氏穩定指數(Ryznar Stability Index, RSI)結果，水質較偏向腐蝕，具不易結垢之特性。透膜壓力(Transmembrane pressure，TMP)與薄膜滲透性關係呈現反比，TMP愈高，滲透性愈低。不同曝氣強度影響掃流速度，曝氣強度控制在40 LPM，可維持較佳滲透性。污泥濃度若控制在4,000~8,000mg/L範圍，對MBR操作較佳。薄膜產水通量控制在2.15 LPM，其滲透性明顯優於2.7 LPM及3.2 LPM，產水通量增加，TMP上升速度亦增快，會加速薄膜積垢速率。維護性藥洗以0.2%鹽酸、進藥2分鐘、進水8分鐘反覆3次循環之效果為佳；恢復性藥洗效果原則以16小時為佳，較能去除/延緩薄膜積垢。此外考量竹科事業製程變動性，須定期進行水質檢測分析，以掌握水質特性。依據薄膜耐酸鹼程度，選擇適合竹科水質特性之薄膜進行操作，並建議操作一段時間後，定期檢視薄膜外觀是否有斷絲或纏繞現象，確保產水水質。關鍵字：薄膜生物反應槽（MBR）、積垢、薄膜滲透性、透膜壓力（TMP） ;Abstract In order to conform with the latest effluent ammonia nitrogen control limitation, Hsinchu Science park sewage treatment plant uses Membrane Bioreactor (MBR) as the key treatment process to enhance the function. The fouling resulted from water characteristics may influence the service life of membrane, so this study aims at the wastewater (sewage) of Hsinchu park sewage treatment plant, and discusses the potential factors in membrane fouling. The specific research content includes the quality of influent and effluent of the sewage treatment plant in last three years, analysis of wastewater characteristics; the model plant with the same process as the actual plant is used for experiment, the parameters are adjusted to understand the influence of different operation factors on membrane fouling. 　　 The findings show that the influent and effluent quality data of sewage plant are used to calculate Langelier Saturation Index (LSI) and Ryznar Stability Index (RSI), the results show that the water is relatively corrosive and unlikely to scale. The transmembrane pressure (TMP) is inversely proportional to the membrane permeability, the higher the TMP is, the lower is the permeability. Different aeration rates influence the crossflow velocity, the permeability is better if the aeration rate is controlled at 40 LPM. If the sludge concentration is controlled at 4,000~8,000mg/L, it is favorable for MBR operation. When the membrane permeate flux is controlled at 2.15 LPM, the permeability is obviously better than 2.7 LPM and 3.2 LPM. The TMP increases faster as the permeate flux increases, the membrane fouling is accelerated. Three cycles of maintenance cleaning procedure with 0.2% HCl, 2 minutes′ agent feed and 8 minutes′ water feed have good effect; 16 hours′ maintenance cleaning procedure is preferred, which is likely to remove/retard membrane fouling. In addition, considering Hsinchu Science Park undertaking process variability, the water quality must be tested periodically, so as to master the water characteristics. According to the acid and alkali resistance of membrane, the membrane suitable for Hsinchu Science Park water characteristics is selected for operation, and it is suggested to periodically check whether the membrane appearance has filament break or wrapping after a period of operation, so as to guarantee the treated water quality. Keywords: membrane bioreactor (MBR); fouling; membrane permeability; transmembrane pressure (TMP)
顯示於類別:	[環境工程研究所碩士在職專班] 博碩士論文

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	292	檢視/開啟

在NCUIR中所有的資料項目都受到原著作權保護.

社群 sharing

資料載入中.....