透水混凝土鋪面加勁設計之研究

NCU Institutional Repository > 工學院 > 土木工程研究所 > 博碩士論文 > Item 987654321/87080

請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/87080

題名:	透水混凝土鋪面加勁設計之研究
作者:	簡宏任;Chien, Hung-Jen
貢獻者:	土木工程學系
關鍵詞:	反覆荷載透水混凝土鋪面;加勁纖維;抗壓強度;彈性模數;開裂模數;混凝土等值應力塊;pervious concrete pavement of repeated load;reinforcing fiber;compressive strength;elastic modulus;modulus of rupture;equivalent stress block of concrete
日期:	2021-07-21
上傳時間:	2021-12-07 14:54:51 (UTC+8)
出版者:	國立中央大學
摘要:	隨著環境的變遷與環保意識的抬頭，透水混凝土鋪面的設置逐漸普及，以改善都市熱島效應，而為了維持良好的滲透性能，因此孔隙率設計要求較高，其透水混凝土強度則受影響，當孔隙率越大，強度則越低。故本研究提出傳統透水混凝土鋪面滲透性能與受較重型車輛之抗彎強度，並加入補強材料作為本研究之主軸。本研究主要探討有加勁材透水混凝土斷面設計，但目前透水混凝土均使用在輕交通量道路，且為純混凝土斷面，故研究設計以實驗方式來求有加勁材之透水混凝土斷面強度相關設計參數。相關設計參數如透水混凝土彈性模數、開裂模數及斷面強度矩形應力塊參數等，均有考慮一般單次荷載與反覆荷載受力行為差異。本研究主要結論為：探討反覆荷載後對透水混凝土鋪面版的影響，比較單次與反覆荷載後的抗壓強度與彈性模數，發現兩者荷載方式之結果相近。研究數據統計，透水混凝土強度f_c^′=15~40MPa，得出透水混凝土之彈性模數E_c=3072√(f_c′)，開裂模數fr=0.86√(f_c′)之經驗公式。文中亦研究透水混凝土應力應變模型研究，發現與Popovics所提出的一般混凝土應力應變曲線模型相近。再者，乃提出不同受力階段透水混凝土等值應力塊參數α_1、β_1，供日後透水混凝土斷面彎矩設計作參考。文中對透水混凝土加勁材之挑選，乃建議使用耐腐蝕之鍍鋅鋼線網格或玻璃纖維網格，兩者均可設計在使用載重與極限載重階段。關鍵字：反覆荷載透水混凝土鋪面、加勁纖維、玻璃纖維網格、鋼線網格、抗壓強度、彈性模數、開裂模數、混凝土等值應力塊。 ;Nowadays, pervious concrete(so called as PC) is one of options to reduce the urban heat island effect. However, the compressive strength of the PC is much lower than the normal concrete because of its nature in higher porosity for the permeability requirement. As the porosity increases,so as the strength of PC decrease. Therefore, in order to improve the resistance of flexural strength for the heavier vehicles on the pervious concrete pavement, this study will be focused on the plain PC strengthened with some advanced reinforcing materials. The purpose of the topic is to discuss the cross-section design of reinforced pervious concrete(so called as RPC). This is because the current PC without reinforcing materials is commonly used in the light traffic. Therefore, the study plans experimental methods to investigate the design parameters for RPC cross-section strength. Relevant design parameters such as PC elastic modulus, modulus of rupture, and section at strength using rectangular stress block method etc., will be discussed, including the effects on the mono-cycle loading and repeated loading. The main conclusions of this study are: The effect of repeated loads on the PC pavement was discussed in the compressive strength and elastic modulus. It was shown that there was no obvious difference between two loading protocal. The statistics showed that the testing of PC strength f_c^′ was 15~40 MPa, and the empirical formula of the elastic modulus of PC E_c=3072√(f_c′) and the modulus of rupture fr=0.86√(f_c′) were obtained. The study on the stress-strain model of PC found that PC stress-strain behavior was similar to the general concrete model proposed by Popovics. The equivalent stress block parameters α_1 and β_1 of the PC are proposed for providing the design of the bending moment of the PC cross-section at different load stages. For the selection of PC reinforcing materials for PC, it is recommended to use galvanized wire grid or glass-fiber grid to resist corrosion.This materials can also be designed in the service load and ultimate load stage. Keywords：pervious concrete pavement of repeated load, reinforcing fiber, glass-fiber grid, steel-reinfored grid, compressive strength, elastic modulus, modulus of rupture, equivalent stress block of concrete
顯示於類別:	[土木工程研究所] 博碩士論文

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	64	檢視/開啟

在NCUIR中所有的資料項目都受到原著作權保護.

社群 sharing

資料載入中.....