中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/92346
English  |  正體中文  |  简体中文  |  全文筆數/總筆數 : 80990/80990 (100%)
造訪人次 : 42415501      線上人數 : 1613
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜尋範圍 查詢小技巧:
  • 您可在西文檢索詞彙前後加上"雙引號",以獲取較精準的檢索結果
  • 若欲以作者姓名搜尋,建議至進階搜尋限定作者欄位,可獲得較完整資料
  • 進階搜尋


    請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/92346


    題名: 狙擊鏡光學設計與其瞄準系統設定
    作者: 林岦品;Lin, Li-Pin
    貢獻者: 光電科學與工程學系
    關鍵詞: 狙擊鏡;橫向色差;光學畸變;Strehl ratio;RMS
    日期: 2023-07-25
    上傳時間: 2024-09-19 15:46:56 (UTC+8)
    出版者: 國立中央大學
    摘要: 提出設計一款40mm口徑十六倍的狙擊鏡,在狙擊鏡系統中可分為物鏡系統、反轉鏡系統與目鏡系統,將三者分開做設計,設計完成後再將三系統組合成狙擊鏡系統,物鏡系統由0.7度半視角為最大入射角度,焦距為176 mm,入瞳口徑為40 mm,目鏡系統由11.0609度為最大出射半視角角度,焦距為22 mm,出瞳為2.5mm,良視距離為50 mm,其中使用反轉鏡系統以利於人眼做觀察。
    我們將對這三系統做波前像差、光學畸變、橫向色差的分析與校正是否達到設計要求,三系統各別設計完成後將三系統組合成狙擊鏡系統其放大倍率為16 X,在完成後,我們再進行一次分析,以驗證成像品質是否符合要求。接著我們將進行公差分析,以確保設計可以進行量產,設計即完成。設計完成後對狙擊鏡瞄準目標物進行修正,根據仰角與風偏影響對目標物的誤差進行修正計算。
    ;A design is proposed for a 16x sniper scope with a 40mm objective diameter. The sniper scope system consists of the objective system, the erecting system, and the eyepiece system, which are designed separately and then combined into the sniper scope system. The objective system has a maximum entrance angle of 0.7 degrees (half field of view), a focal length of 176mm, and an entrance pupil diameter of 40mm. The eyepiece system has a maximum exit angle of 11.0609 degrees (half field of view), a focal length of 22mm, an exit pupil diameter of 2.5mm, and a Eye-Relief of 50mm. The use of the erecting system facilitates observation by the human eye.
    Each system is analyzed and corrected for wavefront aberrations, optical distortion, and lateral chromatic aberration to meet the design requirements. After completing the individual designs of the three systems, they are combined into the sniper scope system with a magnification of 16x. A final analysis is performed to confirm that the imaging quality meets the requirements. Lastly, tolerance analysis is conducted to ensure that the design is suitable for mass production. The design is considered complete. After the design is completed, adjustments are made to the sniper scope to compensate for errors caused by elevation angle and wind deflection when aiming at a target.
    顯示於類別:[光電科學研究所] 博碩士論文

    文件中的檔案:

    檔案 描述 大小格式瀏覽次數
    index.html0KbHTML23檢視/開啟


    在NCUIR中所有的資料項目都受到原著作權保護.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 隱私權政策聲明