銀對於鎂鎳儲氫合金吸放氫及電化學性質之研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：73

、訪客IP：18.118.146.163

姓名

江建璋(Chien-chang Chiang) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

銀對於鎂鎳儲氫合金吸放氫及電化學性質之研究
(ffects of Ag on hydrogen storage properties and electrochemical performances of Mg2Ni alloy)

相關論文

★ 非破壞性探討安定化熱處理對Al-7Mg鍛造合金微結構、機械與腐蝕性質之影響	★ 非破壞性探討安定化熱處理對Al-10Mg鍛造合金微結構、機械與腐蝕性質之影響
★ 冷加工與熱處理對AA7055鍛造型鋁合金微結構與機械性質的影響	★ 冷抽量對AA7055(Al-Zn-Mg-Cu)-T6態合金腐蝕性質和微結構之影響
★ 熱力微照射製作絕緣層矽晶材料之研究	★ 分流擠型和微量Sc對Al-5.6Mg-0.7Mn合金微結構及熱加工性之影響
★ 氧化物催化劑對亞共晶Mg-Ni合金之儲放氫特性研究	★ 熱處理對7050鋁合金應力腐蝕與含鈧鋁薄膜特性之影響研究
★ Ti-V-Cr與Mg-Co基BCC儲氫合金性質研究	★ 鋰-鋁基及鋰-氮基複合儲氫材料之製程開發及研究
★ 銅、鎂含量與熱處理對Al-14.5Si-Cu-Mg合金拉伸、熱穩定與磨耗性質之影響	★ 恆溫蒸發熔煉鑄造製程合成鎂基介金屬化合物及其氫化特性之研究
★ 無電鍍鎳多壁奈米碳管對Mg-23.5wt.%Ni共晶合金儲放氫特性之影響	★ 微量Sc對A356鑄造鋁合金機械性質之影響
★ 熱處理對車用鋁合金材料熱穩定性與表面性質之影響	★ 鍶改良劑、旋壓成型及熱處理對A356鋁合金磨耗腐蝕性質之影響

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

本研究結合自行開發的恆溫揮發鑄造法(Isothermal Evaporation Casting Process, IECP)與球磨法，將不同含量之Ag添加於Mg2Ni合金中，研究Ag在Mg2Ni合金中的形態對於吸放氫與電化學性質之影響。
IECP法可以熔配出高純度的Mg2Ni合金，當Ag添加於Mg2Ni合金時，將形成Mg2Ni(固溶Ag)與Mg3Ag(固溶Ni)兩相，同時IECP鑄態合金的最大吸氫量隨著Ag的添加而下降，但吸氫速率沒有改善，且Ag添加到 Mg2Ni合金中，其PCI曲線呈現雙平台區，第一平台為Mg2Ni合金的氫化反應，第二平台吸氫推測為固溶部分Ni的Mg3Ag吸氫，且經ICEP法之鑄態合金對於電化學性質沒有改善；在球磨法方面，Mg2Ni合金經球磨2小時與5小時後，其XRD結果相仿，均呈現寬化與弱化的現象，而含Ag的球磨合金，在結構上依然有Ag的存在，且在退火後，會產生MgAg相。球磨法Mg2Ni合金其吸氫量下降到2.9wt.%，而含Ag的球磨合金吸氫量下降，是由於MgAg的生成，而Mg2Ni合金經球磨後，電容量提升到100 mAh/g左右，且Ag的添加導致球磨合金降低初始電容量，但循環壽命優於不含Ag之Mg2Ni合金。

摘要(英)

A different ratio of Ag has been added in Mg2Ni by isothermal evaporation casting process (IECP) and ball milling. To research the effects of Mg-Ni-Ag alloys on the hydrogen storage properties and discharge capacity when Ag addition in Mg2Ni with different types (compounds or elements).
A high purity Mg2Ni alloy will be fabricated by IEC-process. There are two phases appeared (partial Ag substituted Mg2Ni and partial Ni substituted Mg3Ag) in Ag added Mg2Ni. The hydrogen storage capacity decrease with sliver content increasing, but hydrogen absorption rate has not improved. The PCI curves show two plateaus in Ag added Mg2Ni. It is found that the hydriding mechanism of the first plateau is Mg2Ni alloy hydrogenation. The second plateau guesses partial Ni substituted Mg3Ag alloy hydrogenation. Ag addition was no effect on the discharge properties. In ball milling, there are similar results for broaden and weakened Mg2Ni and Ag peaks after ball milling 2 hours and 5 hours by X-ray diffraction (XRD). There is the new phase MgAg formed in ball-milled Mg2Ni + 20wt.% Ag alloy after annealing. The maximum hydrogen storage capacity of Mg2Ni alloy reached 2.9 wt.%, but the capacity of Mg2Ni +20wt.% Ag alloy only reached 2.0 wt.%. The capacity decrease is because of the MgAg phase formation. Discharge capacity upgraded to 100 mAh / g after Mg2Ni alloy ball-milled. Ag addition can improve cycle life by ball milling, but the maximum discharge capacities was been reduced.

關鍵字(中)

★ 電化學
★ 球磨法
★ 吸放氫
★ Mg-Ni-Ag 合金
★ IECP

關鍵字(英)

★ electrochemical performances
★ hydrogen storage
★ Ball milling
★ IECP
★ Mg-Ni-Ag alloy

論文目次

一、前言與文獻回顧.................................1
1-1 儲氫材料簡介...................................1
1-2 儲氫合金吸放氫原理介紹.........................3
1-2-1 動力學性質.....................................3
1-2-2 熱力學性質.....................................4
1-3 鎂基儲氫合金介紹...............................7
1-4 儲氫合金的製備方法.............................8
1-5 儲氫合金的電化學原理..........................10
1-6 Mg、Ni、Ag之文獻回顧..........................13
1-7 研究目的與動機................................14
二、實驗方法與流程................................15
2-1 合金熔配......................................15
2-1-1 IECP法製備合金................................15
2-1-2 球磨法製備合金................................15
2-2 微結構分析....................................17
2-2-1 XRD 結構分析..................................17
2-2-2 金相觀測與EPMA分析............................17
2-3 合金儲放氫性質測試............................18
2-3-1 吸氫速率量測..................................18
2-3-2 PCI Curve量測.................................18
2-4 電化學測試....................................18
三、結果與討論....................................20
3-1 IECP 法製配合金...............................20
3-1-1 X 光粉末繞射分析..............................20
3-1-2 金相觀察及電子微探測儀分析....................21
3-1-3 吸氫速率量測..................................23
3-1-4 PCI 曲線測試..................................25
3-1-5 PCI 雙平台之証明..............................27
3-1-6 電化學性質測試................................29
3-2 球磨法製配合金................................30
3-2-1 X 光粉末繞射分析..............................30
3-2-2 吸氫速率量測..................................32
3-2-3 PCI 曲線測試..................................33
3-2-4 電化學性質測試................................35
四、結論..........................................37
五、未來工作................. ....................38
六、參考文獻......................................39

參考文獻

﹝1﹞ N. Khan, N. Mariun, Z. Saleem, N. Abas, “Fossil fuels, new energy sources and the great energy crisis ”, Renewable and Sustainable Energy Reviews, In Press, Corrected Proof, Available online 10 December 2007.
﹝2﹞ Jian Hua, Yi-Hsuan Wu, Pang-Fu Jin, “Prospects for renewable energy for seaborne transportation—Taiwan example ”, Renewable Energy, Vol 33, pp. 1056-1063, 2008.
﹝3﹞ T. Nejat Vezirog˘lu, Sumer S_ah_ın, “21st Century’s energy: Hydrogen energy system”, Energy Conversion and Management, Vol 49, Issue 7, pp. 1820-1831, July 2008.
﹝4﹞ Billur Sakintuna, Farida Lamari-Darkrim, Michael Hirscher, “Metal hydride materials for solid hydrogen storage:Areview ”, International Journal of Hydrogen Energy, Vol.32, pp. 1121-1140, 2007.
﹝5﹞ A Zuttel, “Materials for hydrogen storage”, Mater Today, pp. 24–33, September 2003.
﹝6﹞ G. Liang, “Synthesis and hydrogen storage properties of Mg-based alloys ”, Journal of Alloys and Compounds, Vol 370, pp123–128, 2004.
﹝7﹞ T. Graham, “On the Relation of Hydrogen to Palladium ”, J. Franklin Inst., Vol 87, pp. 256-266, 1869.
﹝8﹞ M. Jurczyk, L. Smardz, K. Smardz, et al., “Nanocrystalline LaNi5-type Electrode Materials for Ni-MHx Batteries ”, J. Solid State Chem., Vol 171, pp. 30, 2003.
﹝9﹞ J.H.N. Vucht, F.A. Kuijpers, H.C.A.M. Bruning, “Reversible Room-Temperature Absorption of Large Quantities of Hydrogen by Intermetallic Compounds ”, Philips Res. Repts., Vol.25, pp. 133, 1970.
﹝10﹞A. Pebler and E.A. Gulbransen, “Equilibrium Studies on the Systems ZrCr2-H2, ZrV2-H2 and ZrMo2-H2 Between 0℃ and 900℃ ”, Trans. Metall. Soc. AIME, Vol 239, pp. 1593, 1967.
﹝11﹞J.J. Reilly, R.H. Wiswall, “The Reaction of Hydrogen with Alloys of Magnesium and Nickel and the Formation of Mg2NiH4”, Inorg. Chem., Vol 7, pp. 2254, 1968.
﹝12﹞J.J. Reilly, R.H. Wiswall, “Formation and Properties of Iron Titanium Hydride ”, Inorg. Chem., Vol 13, pp. 218, 1974.
﹝13﹞林美姿, “儲氫合金之開發與應用 ”, 材料與社會, Vol 81, pp. 61, 1993.
﹝14﹞C.R. Clark, C. Wright, C. Suryanarayana, E.G. Baburaj, F.H. Froes, “Synthesis of Mg2X (X = Si, Ge, or Sn) intermetallics by mechanical alloying ”, Materials Letters, Vol.33, pp. 71-75, 1997.
﹝15﹞G. Liang, J. Huot, S. Boily, A. Van Neste, R. Schulz, “Catalytic effect of transition metals on hydrogen sorption in nanocrystalline ball milled MgH2–Tm(Tm = Ti, V, Mn, Fe and Ni) systems ”, Journal of Alloys and Compounds, Vol.292, pp. 247–252, 1999.
﹝16﹞Hao Gu, Yunfeng Zhu, Liquan Li, “Characterization of hydrogen storage properties of Mg-30 wt.% Ti1.0V1.1Mn0.9 composite ”, Journal of Alloys and Compounds, Vol 424, pp. 382-387 9, November 2006.
﹝17﹞Yongfeng Liu, Zhitao Xiong, Jianjiang Hu, Guotao Wu, Ping Chen, Kenji Murata, Ko Sakata, ”Hydrogen absorption/desorption behaviors over a quaternary Mg–Ca–Li–N–H system ”, Journal of Power Sources, Vol 159, pp. 135-138, 13 September 2006.
﹝18﹞J.L. Lou, N. Cui, “Effects of microencapsulation on the electrode behavior of Mg2Ni-based hydrogen storage alloy in alkaline solution ”, J. Alloys Comp., Vol 264, pp. 299, 1998.
﹝19﹞C. Suryanarayana, “Mechanical Alloying and Milling ”, Prog. Mater. Sci., Vol.46, pp.1, 2001.
﹝20﹞H. Sakaguchi, T. Sugioka and G.Y. Adachi, “Hydrogen Absorption Characteristics of Crystalline LaNi5 Prepared by Mechanical Alloying ”, Chemistry Letters, Vol.7, pp. 561, 1995.
﹝21﹞T. Sakai, I. Uehara and H. Ishikawa, “R&D on Metal Hydride Materials and Ni–MH Batteries in Japan ”, J. Alloys Comp., Vol 293-295,
pp. 762-769, 1999.
﹝22﹞黃鐵生,“儲氫合金概論”,工業材料, Vol 111, pp.97-107, 1996.
﹝23﹞N. Cui and J.L. Luo, “An AC Impedance Study of Self-Discharge Mechanism of Nickel-Metal Hydride (Ni-MH) Battery Using Mg2Ni-Type Hydrogen Storage Alloy Anode ”, Electrochimica Acta, Vol 45, pp. 3973-3981, 2000.
﹝24﹞.J.H. Lee, K.Y. Lee and J.Y. Lee, “Self-Discharge Behavior of Sealed Ni-MH Batteries Using MmNi3.3+xCo0.7Al1.0-x Anodes ”, J. Alloys Comp., Vol 232,
p p. 197, 1996
﹝25﹞J.J.G. Willems and K.H.J. Buschow, “From Permanent Magnets to Rechargeable Hydride Electrodes ”, J. Less-Common Met., Vol 129, pp.13, 1987.
﹝26﹞C. Iwakura, Y. Kajiya, H. Yoneyama and et al., “Self-Discharge Mechanism of Nickel-Hydrogen Batteries Using Metal Hydride Anodes ”, J. Electrochem. Soc., Vol 136, pp. 1351, 1989.
﹝27﹞B.H. Liu, Z.P. Li, Y. Matsuyama and et al., “Corrosion and Degradation Behavior of Zr-Based AB2 Alloy Electrodes During Electrochemical Cycling ”, J. Alloys Comp., Vol 296, pp. 201-208, 2000
﹝28﹞X. Baojia, S. Pengfei and et al., “Degradation Mechanism of the Mish Metal Alloy Hydride Electrodes ”, J. Alloys Comp., Vol 293-295, pp.737-741, 1999
﹝29﹞M. Geng and D.O. Northwood, “The Characteristic of the Negative Electrode of A Nickel-Metal Hydride Battery ”, Int. J. Hydrogen Energy, Vol 21, pp. 887-890, 1996.
﹝30﹞Lian-bang Wang, Yuan-hua Tang, Yi-jing Wang, Qiu-Di Li, He-nan Song, Hua-bin Yang, “The hydrogenation properties of Mg2Ag0.2Ni1.8 alloy” , J. Alloys Comp., Vol.336, pp. 297-300, 2002.
﹝31﹞Qian Li, Qin Lin, Lijun Jiang, Kou-Chih Chou, Zhan Feng, Qiang Zheng, Xiuying Wei, “Properties of hydrogen storage alloy Mg2-xAgxNi(x=0.05, 0.1, 0.5) by hydriding combustion synthesis ”, J. Alloys Comp., Vol 359, pp. 128-132, 2003.
﹝32﹞Qian Li , Li-jun Jiang, Kuo-chih Chou , Qin Lin , Zhan Feng, Kuang-di Xu , Xiong-gang Lu , Jie-yu Zhang, “Effect of hydrogen pressure on hydriding kinetics in the Mg2−xAgxNi–H (x = 0.05, 0.1) system ”, J. Alloys Comp., Vol 399, pp. 101-105, 2005.
﹝33﹞T. Kohno , M. Yamamoto, M. Kanda, “Electrochemical properties of mechanically ground Mg2Ni alloy ”, J. Alloys Comp., Vol.293-295, pp. 643-647, 1999.
﹝34﹞Che-Wei Hsu, Sheng-Long Lee, Rong-Ruey Jeng, Jing-Chie Lin, “Mass production ofMg2Ni alloy bulk by isothermal evaporation casting process ”, International Journal of Hydrogen Energy, Vol 32, pp. 4907-4911, December 2007.
﹝35﹞K. Aoki, T. Masumoto and J. Kamachi, “Hydrogen Absorption and Desorption Properties of Amorphous Ti---Ni and Hf---Ni Alloys ”, J. Less-Common Met, Vol 113, pp. 33, 1985.

指導教授

李勝隆(Sheng-long Lee)

審核日期

2008-7-17

推文