圓柱體形建築物表面風壓之實驗研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：181

、訪客IP：3.135.198.150

姓名

李肇軒(Tsao-Hsuan Li) 查詢紙本館藏

畢業系所

土木工程學系

論文名稱

圓柱體形建築物表面風壓之實驗研究
(pressure distribution on the surface of three-dimensional circular cylinder in a boundary layer flow)

相關論文

★ 定剪力流中二維平板尾流之風洞實驗	★ 以大渦紊流模式模擬不同流況對二維方柱尾流之影響
★ 矩形建築物高寬比對其周遭風場影響之研究	★ 台灣地區風速機率分佈之研究
★ 邊界層中雙棟並排矩形建築之表面風壓量測	★ 排放角度與邊牆效應對浮昇射流影響之實驗研究
★ 低層建築物表面風壓之實驗研究	★ 最大熵值理論在紊流剪力流上之應用
★ 應用遺傳演算法探討海洋放流管之優化方案	★ 均勻流中圓柱體形建築物表面風壓之風洞實驗
★ 大氣與森林之間紊流流場之風洞實驗	★ 以歐氏-拉氏法模擬煙流粒子在建築物尾流區中的擴散
★ 以HHT分析法研究陣風風場中建築物之表面風壓	★ 以HHT時頻分析法研究陣風風場中物體所受之風力
★ 風吹落物之軌跡預測模式與實驗研究	★ 海洋放流管之敏感度分析與最佳化設計

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本研究以風洞實驗的方式探討邊界層流中三維圓柱體形建築物表面的壓力分佈情形。實驗條件包括光滑圓柱體以及兩種不同粗糙度的圓柱體，實驗中使用電子式壓力掃描器，可同時量測多個位置的瞬時壓力。由實驗結果可計算得建築物表面的平均、擾動、最大壓力分佈與流場分離點位置。研究結果顯示：圓柱體的最大擾動壓力發生在最大負壓發生處；當圓柱體粗糙程度增加時，圓柱體的最大負壓和擾動壓力隨之減少。且最大負壓發生處和圓柱體分離點的平均位置皆會隨著粗糙度增加而往迎風方向移動，分離點移動的範圍則會隨著粗糙度增加而變小。風壓頻譜顯示渦流逸散頻率為12 Hz，史徹荷數為0.21，與二維圓柱體的史徹荷數相近。本研究之結果可幫助吾人瞭解對邊界層流中三維圓柱體表面粗糙度對流況與壓力分佈的影響，可供相關工程設計之參考。

摘要(英)

This study experimentally investigates the pressure distribution on the surface of three-dimensional circular cylinder in a boundary layer flow. The experiments were carried out in an atmospheric boundary layer wind tunnel. The flow conditions include three different kinds of surface roughness. Instantaneous fluctuating wind pressures were measured by an electronic pressure scanner. Based on the pressure measurement, the distributions of mean, rms Cprms, peak pressure Cpp and separation point can be calculated. It was found that the maximum Cprms occurs at the location of minimum negative pressure. Also, the separation point and the location of minimum negative pressure will move toward upstream direction as surface roughness increase. Even under the same surface roughness, the separation point will move within certain range in turbulent flow. The moving range of separation point will decrease as surface roughness increase. The experimental results also revealed that the probability of pressure fluctuations for positive pressure are close to the Gaussian distribution function. On the other hand, negative pressure side was skewed and did not necessary follow Gaussian distribution.

關鍵字(中)

★ 圓柱體
★ 擾動壓力
★ 粗糙度

關鍵字(英)

★ pressure fluctuation
★ surface roughness
★ circular cylinder

論文目次

中文摘要…………………………………………………………i
英文摘要…………………………………………………ii
目錄………………………………………………………iii
圖目錄……………………………………………………vi
表目錄……………………………………………………xi
符號表……………………………………………………xii
第一章緒論…………………………………………1
1.1 前言…………………………………………………1
1.2 研究動機……………………………………………2
1.3 研究內容及大綱……………………………………2
第二章理論基礎與文獻回顧………………………3
2.1 大氣邊界層…………………………………………3
2.2 大氣紊流特性………………………………………5
2.2.1 紊流強度…………………………………………5
2.2.2 雷諾剪應力………………………………………6
2.3 風流經圓柱體之行為………………………………7
2.4 表面風壓……………………………………………7
2.5 風洞模擬與邊界層流流場相性……………………10
2.6 準穩態假設…………………………………………14
2.7 前人文獻回顧………………………………………17
第三章實驗設備與方法……………………………23
3.1 大型環境風洞………………………………………23
3.2 風速量測方法………………………………………24
3.3 壓力量測方法………………………………………26
3.3.1 前人研究…………………………………………26
3.3.2 壓力量測儀器……………………………………28
3.3.3 儀器校正…………………………………………30
3.3.4 壓力量測…………………………………………31
3.4 實驗方法 ……………………………………………33
3.4.1 大氣邊界層模擬與建築物模型…………………33
3.4.2 實驗數據採樣技巧………………………………35
3.4.3 實驗數據採樣與處理……………………………35
3.5 頻譜分析方法………………………………………35
第四章實驗結果與討論……………………………50
4.1 迫近流場……………………………………………50
4.1.1 平均風速剖面……………………………………50
4.1.2 紊流強度剖面……………………………………51
4.1.3 紊流頻譜…………………………………………51
4.2 光滑圓柱體表面風壓………………………………51
4.2.1 平均風壓…………………………………………51
4.2.2 擾動風壓…………………………………………52
4.2.3 極值風壓……………….………………………53
4.2.4 風壓頻譜……………….………………………56
4.2.5 準穩態假設驗證…………………………………57
4.3 粗糙圓柱體表面風壓………………………………58
4.3.1 平均風壓…………………………………………58
4.3.2 擾動風壓…………………………………………60
4.4 圓柱體分離點的探討………………………………61
4.4.1 分離點的界定……………………………………61
4.4.2 分離點位置及移動範圍…………………………63
4.5 擾動風壓的機率分佈………………………………64
第五章結論與建議…………………………………113
5.1 結論…………………………………………………113
5.2 建議…………………………………………………114
參考文獻…………………………………………………………116

參考文獻

1. 蔡益超、林宗賢，”建築物所受風力有關規範之研擬”，行政院國家科學委員會，防災科技研究報告73-24號 (1984)
2. 陳俊傑 “高層建築之環境風與風壓實驗研究(以良美凱悅飯店為例)”，國立成功大學建築研究所碩士論文 (1995)
3. 陳若華 ”結構振動與流場互制現象之風動實驗研究”，淡江大學土木工程研究所博士論文 (1996)
4. 蔡益超、陳瑞華、項維邦，”建築物風力規範條文、解說及示範例之研訂”，內政部建築研究所研究報告 (1996)
5. 朱佳仁 ”國立中央大學大型環境風洞之簡介”，國立中央大學土木工程學系 (1997)
6. 張瑞楨 “邊界層流中方柱體尾流之風洞實驗”，國立中央大學土木工程研究所碩士論文 (1998)
7. 朱佳仁 “高層建築物風場環境評估規範研議”，內政部建築研究所研究報告 (2000)
8. 中華民國內政部營建署 “建築技術規則(91年1月修正版)”，內政部營建署法規 (2000)
9. 卓勇志 “邊界層中雙棟並排矩形建築隻表面風壓量測”，國立中央大學土木工程研究所碩士論文 (2001)
10. Achenbach, E., “Distribution of local pressure and skin friction around a circular cylinder in cross-flow up to ”, Journal of Fluid Mechanics, Vol.34, part 4, pp.625-639 (1968)
11. Achenbach, E., “Influence of surface roughness on the cross-flow around a circular cylinder”, Journal of Fluid Mechanics, Vol.46, part 2, pp.321-335 (1970)
12. Adachi, T., “Effects of surface roughness on the universal Strouhal number over the wide Reynolds number range”, Journal of Wind Engineering and Industrial Aerodynamics,Vol.69, pp.399-412 (1997)
13. Banks, D. and Meroney, R.N., “The applicability of quasi-steady theory to pressure statistics beneath roof-top vortices”, Journal of Wind Engineering and Industrial Aerodynamics,Vol.89, pp.569-598 (2001)
14. Batham, P.W., “Pressure distributions on circular cylinders at critical Reynolds numbers”, Journal of Fluid Mechanics, Vol.57, pp.209-228 (1973)
15. Bearman, P.W., “On vortex shedding from a circular cylinder in the critical Reynolds number regime”, Journal of Fluid Mechanics, Vol.37, pp.577-585 (1969)
16. Bendat, J.S. and Piersol, A.G., “Random Data : Analyis and Measurement Procedures”, 3rd editions, Johns Wiley & Sons, Inc (2000)
17. Dwyer, H.A. and Mccroskey, W.J., “Oscillating flow over a cylinder at large Reynolds number”, Journal of Fluid Mechanics, Vol.61, part 4, pp.753-767 (1973)
18. Güven, O., Farell, O., and Patel, V.C., “Surface-roughness effects on the mean flow past circular cylinders”, Journal of Fluid Mechanics, Vol.98, part 4, pp.673-701 (1980)
19. Kiya, M., Suzuki, Y., Arie, M., and Hagino, M., “A contribution to the free-stream turbulence effect on the flow past a circular cylinder”, Journal of Fluid Mechanics, Vol.115, pp.151-164 (1982)
20. Lawson, T, “Building Aerodynamics”, Imperial College Press (2001)
21. Letchford, C.W., Iverson, R.E., and Mcdonald, J.R., “The application of Quasi-steady Theory to full scale measurements on the Texas Tech Building”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.48, pp.111-132 (1993)
22. Luo, S.C., Gan, T.L., and Chew, Y.T., “Uniform flow past one (or two in tandem) finite length circular cylinder(s)”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.59, pp.69-93 (1996)
23. Maruta, E., Kanda, M., and Sato, J., “Effects on surface roughness for wind pressure on glass and cladding of buildings”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.74, pp.651-663 (1998)
24. Moody, L.F., “Friction factors for pipe flow”, Transactions of ASME, Vol.66 (1944)
25. Nakamura,Y. and Tomonari, Y., “The effects of surface roughness on the flow past circular cylinders at high Reynolds numbers”, Journal of Fluid Mechanics, Vol.123, pp.363-378 (1982)
26. Nishimura, H. and Taniike, Y., “Aerodynamic characteristics of fluactuating forces on a circular cylinder”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.89, pp.713-723 (2001)
27. Okamoto, S.and Sunabashiri, Y., “Vortex shedding from a circular cylinder of finite length placed on a flat plate”, Journal of Fluid Mechanics, Vol.114, pp.512-537 (1992)
28. Roshko, A., “Experiments on the flow past a circular cylinder at very high Reynolds number”, Journal of Fluid Mechanics, Vol.10, pp.345-356 (1960)
29. Schewe, G., “On the force fluctuations acting on a circular cylinder in crossflow from subcritical up to transcritical Reynolds numbers”, Journal of Fluid Mechanics, Vol.133, pp.265-285 (1983)
30. Simiu, E. and Scanlan, R.H., “Wind Effect on Structures”, 3rd edition, Johns Wiley & Sons,Inc (1996)
31. Uematsu, Y. and Yamada, M., “Effects of aspect ratio and surface roughness on th time-averaged aerodynamic forces on cantilevered circular cylinders at high Reynolds number”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.54-55, pp.301-312 (1995)
32. Uematsu, Y. and Isyumov, N., “Peak gust pressure acting on the roof and wall edges of a low-rise building”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.77-78, pp.217-231 (1998)
33. Uematsu, Y. and Isyumov, N., “Wind pressure acting on low-rise buildings”, Journal of Wind Engineering and Industrial Aerodynamics, Vol.82, pp.1-25 (1999)
34. Zdravkovich, M.M., “Flow around Circular Cylinders”, Journal of Fluid Mechanics, Vol.350, pp.377-388 (1997)

指導教授

朱佳仁(Chia-Ren Chu)

審核日期

2003-6-12

推文