應用鑄鍛生產高、中強度與高延性鋁合金

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：75

、訪客IP：3.138.137.199

姓名

張哲維(Che-wei Chang) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

應用鑄鍛生產高、中強度與高延性鋁合金

相關論文

★ 7005與AZ61A拉伸、壓縮之機械性質研究	★ 雷射去除矽晶圓表面分子機載污染參數的最佳化分析
★ 球墨鑄鐵的超音波檢測	★ 模具溫度對TV前框高亮光澤產品研討
★ 高強度7075-T4鋁合金之溫間成形研究	★ 鎂合金燃燒、鑽削加工與表面處理之研究
★ 純鈦陽極處理技術之研發	★ 鋁鎂合金陽極處理技術之研發
★ 電化學拋光處理、陽極處理中硫酸流速與封孔處理對陽極皮膜品質之影響	★ 電解液溫度與鋁金屬板表面粗糙度對陽極處理後外觀的影響
★ 製程參數對A356鋁合金品質的影響及可靠度的評估	★ 噴砂與前處理對鋁合金陽極皮膜品質的影響
★ 鎂合金回收重溶之品質與疲勞性質分析	★ 鋁合金熱合氧化膜與陽極氧化膜成長行為之研究
★ 潤滑劑與製程參數對Al-0.8Mg-0.5Si鋁合金擠壓鑄件的影響	★ 摩擦攪拌製程對AA5052鋁合金之微觀組織及對陽極皮膜的影響

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

本實驗主要合金成份以Al-8Zn-2Mg-1.5Cu-xZr合金(x為0.15、0.49)、Al-1.0Mg-0.6Si-0.2Cu合金及Al-1.2Mg-1.0Si-1.0Cu-0.15Zr合金做為實驗材料，澆鑄船型模、Y-block金屬模尺寸為100×40×100 mm。船型模鑄件均質化、退火後固溶再T6處理；Y-block鑄件施以同樣均質化與退火後兩道次熱鍛60%變形量，最後固溶和T6處理。將時效後的兩種材料加工成拉伸試棒並測試拉伸性質，比較不同試棒的拉伸性質和微結構。
在鑄/鍛熱鍛變形量約60%後固溶及T6處理，可獲得高強度Al-8Zn-2Mg-1.5Cu-0.49Zr合金抗拉強度為583MPa和延伸率為8.4%；Al-1.2Mg-1.0Si-1.0Cu-0.15Zr合金，可得中高強度抗拉強度為420MPa和延伸率為10%；Al-1.0Mg-0.6Si-0.2Cu合金，可得良好延伸率為16%及適當抗拉強度為310MPa。

摘要(英)

Three groups of alloys of Al-8Zn-2Mg-1.5Cu-xZr(x=0.15、0.49)、Al-1.0Mg-0.6Si-0.2Cu and Al-1.2Mg-1.0Si-0.15Zr were prepared and melted in this study to get boat molds and Y-block permanent mold castings in size of 100×40×100mm. After homogenization and annealing, the boat mold casting were removed for solution treatment and T6 treatment; the Y-block castings would subject to two passes of hot forged with 60% deformation then removed for solution treatment and T6 treatment. After aging all samples were machined to the standard tensile test specimens to get tensile strengths of different samples. Microstructures and tensile properties of different samples were compared and discussed.
After the cast/forge hybrid process with 60% reduction by hot deformation, solution and aging treatment, the Al-8Zn-2Mg-1.5Cu-0.49Zr alloy samples obtained high strength of (UTS) 583MPa and 8.4% in elongation; the Al-1.2Mg-1.0Si-1.0Cu-0.15Zr alloy samples acquired moderate strength of (UTS) 420MPa and 10% in elongation; the Al-1.0Mg-0.6Si-0.2Cu alloy samples got excellent elongation of 16% with proper strength (UTS) of 310MPa.

關鍵字(中)

★ 鑄/鍛
★ 拉伸性質
★ 微結構

關鍵字(英)

★ Cast/forge hybrid process
★ Tensile property
★ Microstructures

論文目次

摘要 i
目錄 iii
圖目錄 v
表目錄 vii
第一章前言 1
第二章文獻回顧 2
2-1 常用鑄造鋁合金 2
2-1-1 A356(鋁-矽-鎂)合金特點 2
2-1-2 A380鋁合金之特點(含矽、鐵高之鋁合金) 3
2-2高強度鑄造鋁合金 Al-Zn-Mg-Cu-(Zr) 3
2-2-1 Al-xZn-yMg-(Cu)合金 4
2-2-2 Al-(7-9%)Zn-(2-2.5%)Mg-xCu合金 8
2-2-3 Al-(7-9%)Zn-(2-2.5%)Mg-(1.5-2%)Cu-xZr系鑄造鋁合金 8
2-2-4 Al-xMg-ySi-(Cu)系鑄造鋁合金 10
2-2-5 鑄鍛不同等級鋁合金的挑戰 11
2-3 提升鑄造鋁合金鑄件品質的注意事項和方法 13
2-3-1 冒口(riser) 13
2-3-2 均質化處理(homogenization treatment) 13
2-3-3固溶處理(solution treatment) 14
2-3-4時效處理(aging treatment) 15
2-3-5塑性變形對鋁合金性質的影響 16
2-3-6氧化膜 18
2-3-7介在物顆粒 19
2-3-8 其他注意事項 20
第三章實驗步驟與方法 21
3-1 實驗材料 21
3-2實驗設備 21
3-3試棒尺寸與模具 22
3-4 實驗步驟 24
第四章結果與討論 29
4-1小爐次實驗結果與討論 29
4-1-1 成份與熱處理實驗 29
4-1-2 熱處理參數最佳化與變形的影響 30
4-1-3 微結構 32
4-2 大爐次實驗結果與討論 34
4-2-1 除氣/除渣實驗 34
4-3 高強度Al-8Zn-2Mg-1.5Cu-(xZr)鑄/鍛鋁合金的機械性質與微結構 36
4-3-1高強度Al-8Zn-2Mg-1.5Cu鑄/鍛鋁合金 38
4-3-2高強度Al-8Zn-2Mg-1.5Cu-0.15Zr鑄/鍛鋁合金 42
4-3-3高強度Al-8Zn-2Mg-1.5Cu-0.49Zr鑄/鍛鋁合金 46
4-3-4 高強度鑄/鍛鋁合金的理想參數 52
4-4 高延性Al-1.0Mg-0.6Si-0.2Cu鑄/鍛鋁合金機械性質與微結構 53
4-5 中高強度Al-1.2Mg-1.0Si-1.0Cu-0.15Zr鑄/鍛鋁合金機械性質與微結構 58
第五章結論 64
參考文獻 65
附錄 73

參考文獻

1. G. Lesile Armstrong, Robert D. Luckett, "Aluminum Die Casting Alloys", Die casting engineer, January-February 1984, pp. 10-16
2. "Standard Specification for Aluminum-Alloy Permanent Mold Casting", pp45
3. B. Closset, J. E. Gruzleski, "Mechanical Properties of A356.0 Alloys Modified with Pure Strontium", AFS Transactions, Vol.31, 1982, pp. 453~464.
4. G. K. Sigworth, M. M. Guzowski, "Grain Refining of Hypoeutectic Al-Si Alloys", AFS Transactions, 1985, pp.907-912.
5. D. Apelian, J. J. A. Cheng, "Al-Si Processing Variables: Effect on Grain Refinement and Eutectic Modification", AFS Transactions, 1986, pp.797-808.
6. T. J. Hurley, R. G. Atkinson, "Effect of Modification Practice on Aluminum A356 Alloys", AFS Transactions, 1985, pp.291-296.
7. J. R. Davis, Davis & Associates, ASM Handbook :Aluminum and Aluminum Alloys, Fabrication and Finishing of Aluminum Alloys, American Society for Metals, 1993, pp.222.
8. H. Toda,P. C. Qu,S. Ito,K. Shimizu,K. Uesugi,A. Takeuchi,Y. Suzuki and M. Kobayashi,"Formation behaviour of blister in cast",International Journal of Cast Metals Research,Vol.27,No.6(2014),pp.369-377
9. Naoyuki Tsumagri,“ Effect of Casting Thickness and Casting Conditions on the Tensile Properties of A380 and ADC12 Alloy High Pressure Die Castings ”,Transactions, NADCA, 2003, Paper No. T03-093.
10. M. Makhlouf, Diran Apelian and Libo Wang, ”MICROSTRUCTURES AND PROPERTIES OF ALUMINUM DIE CASTING ALLOYS ”,NADCA, 1998
11. F.A.Fasoyinu and J. E. Gruzleski, “ The Effect of Magnesium Concentration on the Tensile and Impact Properties of Die Cast Specimens of Aluminum Die Cast Alloy A380.0 ” , Transactions, NADCA, 1995, Paper No. T95-071
12 Kenneth N.Obiekea, Shekarau Y.Aku,Danjuma S.Yawas "Effect of Pressure on the Mechanical Propertues and Microstructure of Die Cast Aluminum A380 Alloy"
13. Ki-Tae Kim,Jeong-Min Kim,Ki-Dug Sung,Joong-Hwan Jun and Woon-Jae Jung,"Effect of Alloying Elements on the Strength and Casting Characteristics of High Strength Al-Zn-Mg-Cu Alloys",Materials Science Forum,Vols.475-479(2005),pp.2539-2542
14. S.H. Seyed Ebrahimi, M. Emamy, N. Pourkia, H.R. Lashgari,"The microstructure, hardness and tensile properties of a new super high strength aluminum alloy with Zr addition",Materials and Design, Vol.31(2010),pp.4450–4456
15. J. Dong,J.Z. Cui, F.X. Yu, Z.H. Zhao, Y.B. Zhuo,"A new way to cast high-alloyed Al–Zn–Mg–Cu–Zr for super-high strength and toughness",Journal of Materials Processing Technology, Vol.171,2006,pp.399–404
16. S.L.Nikitin,Dzhu Men TI,"Al-Zn-Mg-Based Cast Alloys Having High Mechanical Properties",Russian Metallurgy,2010,No.1,pp.41-47
17. ZIYONG CHEN, YUANKE MO, and ZUOREN NIE,"Effect of Zn Content on the Microstructure and Properties of Super-High Strength Al-Zn-Mg-Cu Alloys",
METALLURGICAL AND MATERIALS TRANSACTIONS A, Vol.44A,2013,pp.3910-3920
18. G. Sha and A. Cerezo,"Early-stage precipitation in Al–Zn–Mg–Cu alloy (7050)", Acta Materialia,Vol.52(2004)pp.4503–4516.
19. S.H. Seyed Ebrahimi, M. Emamy,"Effects of Al–5Ti–1B and Al–5Zr master alloys on the structure, hardness and tensile properties of a highly alloyed aluminum alloy",Materials and Design,Vol.31 (2010)pp.200–209
20. H.C.Fang, K.H.Chen,X.Chen,L.P.Huang,G.S.Peng,B.Y.Huang,"Effect of Zr,Cr andPr additions on microstructures and properties of ultra-high strength Al–Zn–Mg–Cu alloys",Materials Science and Engineering A,Vol.528 (2011),pp7606–7615
21. H.C. Fang, H. Chao, K.H. Chen,"Effect of Zr, Er and Cr additions on microstructures and properties of Al–Zn–Mg–Cu alloys", Materials Science & Engineering A,Vol.610 (2014)pp.10–16
22. O.N.SENKOV, R.B. BHAT, S.V. SENKOVA, and J.D.SCHLOZ,"Microstructure and Properties of Cast Ingots of Al-Zn-Mg-Cu Alloys Modified with Sc and Zr",Metallurgical and Materials Transactions A,Vol.36A(2005)pp.2115-2126
23. XingGuo Zhang,FeiQiang Mei,HuanYue Zhang,ShaoHua Wang, CanFeng Fang,Hai Hao,"Effects of Gd and Y additions on microstructure and properties of Al–Zn–Mg–Cu–Zr alloys",Materials Science & Engineering A, Vol.552(2012)pp.230-235
24. Guosheng Peng, Kanghua Chen, Huachan Fang, Songyi Chen,"Effect of Cr and Yb additions on microstructure and properties of low copper Al–Zn–Mg–Cu–Zr alloy",Materials and Design, Vol.36(2012)pp.279-283
25. L.I.Kaigorodova,E.I.Sel′nikhina,E.A.Tkachenko,and O.G.Senatorova,"Effect of Small Additions of Sc and Zr on the Structure and Mechanical Properties of an Al-Zn-Mg-Cu Alloy ",THE PHYSICS OF METALS AND METALLOGRAPHY, Vol.81,No.5(1996)pp.513-519
26. Dawid Kapinos,Marcin Szymanek,Boguslaw Augustyn,Maciej Gawlik,"Effect of Heat Treatment on the Mechanical Properties of Wrought Al-Zn-Mg-Cu Alloy Cast by Rapid Solidification",Material Science Forum, Vol.765(2013) pp.496-500
27. Y.V.Milman,A.I.Sirko,D.V.Lotsko,O.N.Senkov and D.B.Miracle, "Microstructure and Mechanical Properties of Cast and Wrought Al-Zn-Mg-Cu Alloys Modified with Zr and Sc" ,Materials Science Forum Vols.396-402 (2002)pp.1217-1222
28. F.Q.Ran, L.H.Chai, K.Y.Gao, Z.R.Nie and Z.Y.Chen, "Influence of various aging treatments on microstructure,strength and corrosion behaviour of high Zn content Al-Zn-Mg-Cu alloy", Corrosion Engineering,Science and Technology,Vol.49,No.8(2014) pp.712-718
29. Ling-Mei Wu, Wen-Hsiung Wang, Yung-Fu Hsu, Shan Trong,"Effects of homogenization treatment on recrystallization behavior and dispersoid distribution in an Al–Zn–Mg–Sc–Zr alloy",Journal of Alloys and Compounds,Vol.456 (2008) pp.163–169
30. Tomo OGURA, Shoichi HIROSAWA and Tatsuo SATO,"Effects of precipitate microstructures near grain boundaries on strength and ductility in Al–Zn–Mg（–Ag）alloys",Journal of Japan Institute of Light Metals, Vol.56, No.1(2006)pp.644–650
31. Masatomo Nishi,Kenji Matsuda,Naoya Miura,Katsumi Watanabe,Susumu Ikeno,Tomoo Yoshida,Satoshi Murakami,"EFFECT OF THE Zn/Mg RATIO
ON MICROSTRUCTURE AND MECHANICAL PROPERTIES IN Al-Zn-Mg ALLOYS", Materials Science Forum Vols.794-796 (2014)pp.479-482
32. Yunjia Shi, Qinglin Pan, Mengjia Li, Xing Huang, Bo Li,"Inﬂuence of alloyed Sc and Zr, and heat treatment on microstructures and stress corrosion cracking of Al–Zn–Mg–Cu alloys",Materials Science & Engineering A,Vol.621 (2015)pp.173-181
33. Yubo Zuo, Jianzhong Cui, Jie Dong, Fuxiao Yu,"Effects of low frequency electromagnetic ﬁeld on the as-cast microstructures and mechanical properties of superhigh strength aluminum alloy",Materials Science and Engineering A408 (2005) pp.176–181
34. K.H.W.Seah, S.C.Sharma, "Fracture Toughness of Cast Al-Zn-Mg Alloys",J.Mater.Sci.Technol,Vol.12(1996) pp.199-202
35. H.R.Hashemi,H.Ashoori and P.Davami,"Microstructure and tensile properties of squeeze cast Al-Zn-Mg-Cu alloy",Materials Science and Technology ,Vol.17(2001) pp.639-644
36. Chandan Mondal, A.K. Mukhopadhyay,"On the nature of T(Al2Mg3Zn3) and S(Al2CuMg) phases present in as-cast and annealed 7055 aluminum alloy",Materials Science and Engineering A Vol.391 (2005) pp.367–376
37. Gen Li, Naiqin Zhao, Tao Liu, Jiajun Li, Chunnian He, Chunsheng Shi,Enzuo Liu, Junwei Sha,"Effect of Sc/Zr ratio on the microstructure and mechanical properties of new type of Al–Zn–Mg–Sc–Zr alloys",Materials Science & Engineering A,Vol.617 (2014)pp.219-227
38. Zhixiu Wang, Hai Li, Fenfen Miao, Wangjie Sun, Bijun Fang,Renguo Song, Ziqiao Zheng," Improving the intergranular corrosion resistance of Al–Mg–Si–Cu
alloys without strength loss by a two-step aging treatment",Materials Science & Engineering A,Vol.590 (2014) pp.267–273
39. Lipeng Ding, Zhihong Jia, Zhiqing Zhang, Robert E. Sanders, Qing Liu, Guang Yang, "The natural aging and precipitation hardening behavior of Al-Mg-Si-Cu alloys with different Mg/Si ratios and Cu additions",Materials Science & Engineering A , Vol.627 (2015) pp.119–126
40. Tomokazu YAMASHITA, Tooru WATANABE,kenji MATSUDA,Hiroshi ANADA and Susumu IKENO, "Effect of homogenizing treatment and iron content on tensile properties of 6061 aluminum alloy billet produced by continuous casting process",Journal of Japan Institute of Light Metals,Vol.48,No.4(1998)pp.190-194
41. Yi Meng, Jianzhong Cui, Zhihao Zhao, Lizi He, "Effect of Zr on microstructures and mechanicalproperties of an Al-Mg-Si-Cu-Cr alloy prepared by low frequency electromagnetic casting",MATERIALS CHARACTERIZATION,Vol.92(2014) pp.138-148
42. Yi Meng, Jianzhong Cui, Zhihao Zhao, Yubo Zuo,"Effect of vanadium on the microstructures and mechanical properties of an Al–Mg–Si–Cu–Cr–Ti alloy of 6XXX series",Journal of Alloys and Compounds,Vol.573 (2013)pp.102–111
43. Yi MENG, Zhi-hao ZHAO, Jian-zhong CUI," Effect of minor Zr and Sc on microstructures and mechanical properties of Al−Mg−Si−Cu−Cr−V alloys",Trans. Nonferrous Met. Soc. China,Vol.23(2013)pp.1882−1889
44. R. C. Dorward and D. J. Beerntsen: Grain Structure and Quench-Rate Effects on Strength and Toughness of AA7050 Al-Zn-Mg-Cu-Zr Alloy Plate, Metall.Mater. Trans. A, 26A, 1995, pp.2481-2484.
45. M. Conserva, E. Di Russo and O. Caloni: Comparison of the Influence of Chrominum and Zirconium on the Quench Sensitivity of Al-Zn-Mg-Cu Alloys, Metall. Trans., vol. 2, 1971, pp.1227-1232.
46. Hideo Yoshida, Yoshio Baba,"The Role of Zirconium to Improve Strength and Stress-corrosion Resistance of Al-Zn-Mg and Al-Zn-Mg-Cu Alloys",Transactions of the Japan Institute of Metals, Vol.23, No.10 (1982) pp.620-630
47. I.S.KIM and M. C. CHATURVEDI , "Serrated Flow in A1-5 wt.% Mg Alloy",Materials Science and Engineering, vol.37,pp165-172,1979
48. E.A.Brandes and G. B(Editors), Smithells Metals Reference Book, 7th edition, Butter worth-Heinemann, Oxford, 1992
49. D.Altenpohl,“Aluminium”, vol.37, pp.401-411, 1961
50. John E.Hatch, "Aluminum: Properties and Physical Metallurgy", American Society for Metals, USA, pp.145-148, 1984
51. I.J.Polmear" Light Alloys Metallurgy of the Light Metals", 2nd ed.,Edward Arnold, London, England, 1989, pp. 18-143.
52. Kanghua Chen, Hongwei Liu, Zhuo Zhang,Song Li,Richard I. Todd,"The improvement of constituent dissolution and mechanical properties of 7055 aluminum alloy by stepped heat treatments",Journal of Materials Processing Technology Vol.142 (2003) pp.190–196
53. N. Adler, R. DeIASI and G. Geschwind," Influence of Microstructure on the Mechanical Properties and Stress Corrosion Susceptibility of 7075 Aluminum Alloy", Metall. Trans.,vol.3,1972,pp.3191-3200
54. J.K. Park, and A.J. Ardell," Precipitate Microstructure of Peak-aged 7075 Al,Scripta Metallurgica", vol.22,No.7,1988, pp.1115-1119
55. A.J.Sedriks,J. A.S.Green and D.L.Novak," The Influence of Heat Treatment on the Stress-Corrosion Susceptibility of a Ternary Al-5.3 Pct Zn-2.5 Pct Mg Alloy", Metall. Trans.,Vol.4,pp.1992-1994,1973
56. Richard DeIASI and P.N.Adler: Calorimetric Studies of 7000 Series Aluminum Alloys: I.Matrix Precipitate Characterization of 7075, Metall. Trans. A, vol.8A,1977, pp.1177-1183
57. J. Gjonnes and CHR. J. Simensen, " An electron microscope investigation of the microstructure in an Aluminum-Zinc-Magnesium alloy",,Acta Metall.Vol.18, pp.881-890,1970
58. M. PUIGGALI,A. ZIELINSKI,J. M.OLIVE,E. RENAULD, D. DESJARDINS and M. CID,"EFFECT OF MICROSTRUCTURE ON STRESS CORROSION
CRACKING OF AN Al-Zn-Mg-Cu ALLOY",Currosion Science, Vol.40,No.415 pp.805-819,1998
59. Yukio YAMAMOTO, Nobuo SAKATE and Kazuo SAKAMOTO,"Applicability of Cast-Forge Process to Automotive Parts of Al-Zn-Mg Alloys (Effect of Grain Size on Strength)",The Japan Society of Mechanical Engineers,Vol.77,No.775(2011) pp.573-581
60. 廖廷瑋"深冷鍛造與陽極處理對鋁合金7075的疲勞性質及微結構影響研究",碩士論文,民國103年,國立中央大學
61. C.Nyahumwa,N.R.Green and J.Campbell, "Effect of Mould Filling Turbulence on Fatigue Properties of Cast Aluminum Alloys",AFS Transaction Vol.102,pp.98-058
62. N.R.Green and J.Campbell, "Influence of Oxide Film Filling Defects on the Strength of Al-7Si-Mg Alloy Castings",AFS Transaction, Vol.114,pp341-347,1994
63. Yung-Sen Huang,Teng-Shih Shih,Jun-Hung Chou, "Electrochemical behavior of anodized AA7075-T73 alloys as affected by the matrix structure",Applied Surface Science, Vol.283,pp.249-257,2013
64. D.A. Hardwick, A. W. Thompson, I. M. Bernstein: The Effect of Copper Content and Microsturcture on the Hydrogen Embrittlement of Al-6Zn-2Mg Alloys, Metall. Trans., 14A, 1983, pp. 2517-2526.
65. D. Hardie, N. J. H. Holroyd and R. N. Parkins: Effect of Hydrogen on Ductility of a High-Strength Al-Zn-Mg-Cu Alloys, Metal Science, vol.13, 1979, pp. 603-610.
66. G.Mrowka-Nowotnik,"Influence of chemical composition variation and heat treatment on microstructure and mechanical properties of 6xxx alloys",Archives of Materials Science and Engineering,Vol.46,pp.98-107
67. 廖婕如 "一般固溶熱處理與過高溫固溶處理對6066鋁合金時效材拉伸性質與拉伸可靠度之影響",碩士論文,民國101年,成功大學
68. Yi Han, Ke Ma, Lian Li, Wei Chen, Hiromi Nagaumi,"Study on microstructure and mechanical properties of Al–Mg–Si–Cu alloy with high manganese content",Materials and Design,Vol.39 (2012),pp.418-424

指導教授

施登士(Teng-shih Shih)

審核日期

2015-7-28

推文