用過核子燃料最終處置場緩衝材料之潛變實驗及數值分析

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：117

、訪客IP：3.133.124.123

姓名

艾瑞莎(Arintha Indah Dwi Syafiarti) 查詢紙本館藏

畢業系所

土木工程學系

論文名稱

用過核子燃料最終處置場緩衝材料之潛變實驗及數值分析
(Experimental and Numerical Analysis on Creep of Buffer Material in Nuclear Waste Deposition Hole)

相關論文

★ 電弧爐氧化碴特性及取代混凝土粗骨材之成效研究	★ 路基土壤回彈模數試驗系統量測不確定度與永久變形行為探討
★ 工業廢棄物再利用於營建工程粒料策略之研究	★ 以鹼活化技術資源化電弧爐煉鋼還原碴之研究
★ 低放處置場工程障壁之溶出失鈣及劣化敏感度分析	★ 以知識本體技術與探勘方法探討台北都會區道路工程與管理系統之研究
★ 電弧爐煉鋼爐碴特性及取代混凝土粗骨材之研究	★ 三維有限元素應用於柔性鋪面之非線性分析
★ 放射性廢料處置場緩衝材料之力學性質	★ 放射性廢料深層處置場填封用薄漿之流變性與耐久性研究
★ 路基土壤受反覆載重作用之累積永久變形研究	★ 還原碴取代部份水泥之研究
★ 路基土壤反覆載重下之回彈與塑性行為及模式建構	★ 重載交通荷重對路面損壞分析模式之建立
★ 鹼活化電弧爐還原碴之水化反應特性	★ 電弧爐氧化碴為混凝土骨材之可行性研究

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本研究針對用過核子燃料最終處置場緩衝材料之潛變行為進行實驗及數值模擬分析之相關研究。當處置場中的緩衝材料受到來自近場的熱-水-力學-化學(T-H-M-C)耦合效應的影響，會因為處置罐因自重及其他設施所施加的壓力，而造成處置孔位移，故需要進行潛變試驗及數值模擬，避免多重障壁系統受到損害。
本研究透過單軸壓密試驗及直接剪力試驗，以取得SPV200膨潤土的潛變參數。單軸壓密試驗是將膨潤土壓實後的不飽和試體，放入單軸壓密試驗儀中，垂直載重從0.6 MPa開始加載至4.8 MPa。由應變控制剪力試驗中取得應力控制剪力試驗所需的數據，以進行應力控制剪力試驗，其發現在高剪力強度下試體含水量減少且試體乾密度會增加。而應力控制剪力試驗的試體分別為含水量29.2%的壓實試體以及在剪力盒上經水壓飽和的試體。
使用ABAQUS的數值分析是模擬處置孔中的廢料罐、緩衝材料、回填材料及母岩。在第一部分由實驗室取得潛變參數輸入至ABAQUS數值模擬中，結果顯示因廢料罐自重造成的瞬時沉陷量為0.37 mm；而由直接剪力試驗取得潛變參數，顯示出角應變高於參考文獻中的數據；在數值模擬中緩衝材料預計在400年後才會完全飽和，而在廢料罐下的緩衝材料會在10萬年的時候發生潛變，故由數值模擬中的結果表示，對於潛變位移不會對處置設施造成危害；但是當緩衝材料飽和後，因回脹壓力增加導致緩衝材料及回填材料的介面會有最大向上的為位移。

摘要(英)

The buffer material serves a major function in the multiple barrier system for containment of spent nuclear fuels in a geological respository. The deposition hole of high-level nuclear spent fuels components are affected by thermal (T), hydrological (H), mechanical (M), and chemical (C) processes from the near field, referred to as T-H-M-C coupling effects. Bentonite as buffer material is affected by T-H-M-C coupling effects, needs to keep the emplaced canister physically stable to avoid damage caused by displacements and movements initiated by the weight of the canister and stresses exerted by other components of the barrier system.
One-dimensional compression test and direct shear test were performed to determine the creep parameters of SPV200 bentonite. The unsaturated sample compacted and the loading increment for one-dimensional compression test from 0.6 MPa to 4.8 MPa were applied. The strain-controlled direct shear tests were done for obtaining the shear strength of SPV200 bentonite, such that the loading sequence for stress-controlled direct shear test can be obtained. SPV200 bentonite was found to have high shear strength as water content decreases and dry density increases. Stress-controlled direct shear test were run on compacted samples at a saturation water content of 29.2% and on sample saturated in the shear box.
Numerical simulations using ABAQUS were performed on a model incorporating all barrier components in a deposition hole, including the buffer material, the canister, the backfill, and the host rock. The instantaneous settlement caused by canister weight is 0.37 mm as the result of simulation in the first step. The creep parameters obtained from laboratory works were applied as the input for numerical simulation. The creep parameters obtained from direct shear test shows the angular strain rate is higher than the reference. The buffer material was predicted to get fully saturated in 400 years. It is shown that the buffer material under the canister moves upward due to the creep in 100,000 years of time period. And the largest vertical displacement was found to be located at the interface of buffer and backfill caused by the swelling pressure after saturation.

關鍵字(中)

★ 緩衝材料
★ 膨潤土
★ 潛變參數
★ 角應變
★ 潛變位移

關鍵字(英)

★ Buffer material
★ Bentonite
★ Creep parameters
★ Strain rate
★ Vertical displacement

論文目次

ABSTRACT i
摘要 iii
TABLE OF CONTENTS v
LIST OF TABLES ix
LIST OF FIGURES xi
CHAPTER 1 INTRODUCTION 1
1.1 Research Background 1
1.2 Research Objectives 2
1.3 Research Scope 3
1.4 Research Flowchart 4
CHAPTER 2 LITERATURE REVIEW 5
2.1 Design Concept for Storage of Nuclear High-Level Waste 5
2.2 Functional Requirements of Buffer Material 6
2.3 Basic Properties and Microstructure of Bentonite 7
2.4 Mechanical Behavior of Compacted Bentonite 9
2.4.1 Swelling Behavior of Compacted Bentonite 9
2.4.2 Secondary Compression of Unsaturated Bentonite 12
2.4.3 Shear strength of Compacted Bentonite 12
2.4.4 Creep Behavior of Compacted Bentonite 14
2.5 Canister Settlement 26
2.5.1 Physical Process Leading to Canister Settlement 26
2.5.2 Creep Model for Predicting Canister Settlement 31
CHAPTER 3 RESEARCH METHODOLOGY 41
3.1 Research Design 41
3.2 Material 42
3.2.1 Volclay SPV200 bentonite 42
3.2.2 Creep parameters of bentonite as buffer material 42
3.3 One-Dimensional Compression of Bentonite 43
3.3.1 Sample Preparation 43
3.3.2 Test Set-up of One-Dimensional Compression 44
3.3.3 Test program of One-Dimensional Compression 46
3.4 Direct Shear Test of Bentonite 48
3.4.1 Sample Preparation 48
3.4.2 Test Set-up of Direct Shear 53
3.4.3 Test program of Direct Shear 55
3.5 Numerical Simulation using ABAQUS 56
3.5.1 Parameters for creep of bentonite 56
3.5.2 Mechanical Properties 57
3.5.3 Element Mesh 60
3.5.4 Calculation sequence and Step 62
3.5.5 Initial Condition 64
3.5.6 Boundary Conditions 65
CHAPTER 4 RESULTS AND DISCUSSIONS 69
4.1. One-Dimensional Compression Test Result 69
4.2. Direct Shear Test Result 75
4.2.1 Strain-Controlled Direct Shear Test 76
4.2.2 Stress Controlled Direct Shear Test 81
4.2.3 Calculation of Creep Parameters 85
4.3. Numerical Simulation Analysis 90
4.4. Discussion of Experimental and Numerical Simulation on Creep of Buffer Material 97
CHAPTER 5 CONCLUSIONS AND RECOMMENDATIONS 101
5.1 Conclusions 101
5.2 Recommendations 103
REFERENCES 105

參考文獻

Åkesson, M., Kristensson, O., Borgesson, L., Dueck, A., & Hernelind, J. (2010). THM modelling of buffer, backfill and other system components. Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR-10-11).
Borgesson, L., Hokmark, H., & Karnland, O. (1988). Rheological properties of sodium smectite clay. Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR-88-30).
Bucher, F., & Müller-Vonmoos, M. (1989, June). Bentonite as a containment barrier for the disposal of highly radioactive wastes. Applied Clay Science, 4(2), 157-177.
D.C.S Simulia. (2016). ABAQUS/CAE. Dassault Systems. Providence, RI, USA.
Freiesleben, H. (2013). Final Disposal of Radioactive Waste. EPJ Web of Conferences, Vol. 54.
Manepally, C., Fedors, R., Basagaoglu, H., Ofoegbu, G., & Pabalan, R. (2011). Coupled Processes Workshop Report. U.S. Nuclear Regulatory Commission. ( NRC–02–07–006 ).
Mitchell, J. (1976). Fundamentals of soil behavior. John Wiley and Sons. New York.
Pintado, X., Mamunul, H. M., & Martikainen, J. (2013). Thermo-Hydro-Mechanical Tests of Buffer Material. . POSIVA Oy. Eurajoki, Finland. (POSIVA 2012-49).
POSIVA Oy. (2008). Safety Case Plan. POSIVA. Eurajoki, Finland. (POSIVA 2008-05).
Pusch, R. (1986). Settlement of canisters with smectite clay envelopes in deposition holes. . Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR-86-23).
Pusch, R. (1999). Is montmorillonite-rich clay of MX-80 type the ideal buffer for isolation of HLW? . Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR-99-33).
Pusch, R. (2015). Bentonite Clay. Environmental Properties and Applications. CRC Press. Boca Raton, Florida.
Pusch, R., & Adey, R. (1999). Creep in buffer clay . Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR-99-32).
Pusch, R., & Adey, R. A. (1986). Settlement of Clay-enveloped Radioactive canisters. Applied Clay Science, Vol. 1, 353-365.
Pusch, R., Börgesson, L., & Erlström, M. (1987). Alteration of isolating properties of dense smectite clay in repository environment as exemplified by seven pre-quarternary clays . Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR 87-29).
Rutqvist, J., & Tsang, C.-F. (2008). Review of SKB’s Work on Coupled THM Processes Within SR-Can. SKI Report 2008:08.
Savage, D., Lind, A., & Arthur, R. C. (1999). Review of Properties and Uses of Bentonite as a Buffer and Backfill Material. Swedish Nuclear Power Inspectorate. (SKI Report 2008:08).
SKB. (1995). Treatment and final disposal of nuclear waste: Programme for encapsulation, deep geologic disposal, and research, development and demonstration. Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB RD&D Programme 95).
SKB. (2006). Long-term safety for KBS-3 repositories at Forsmark and Laxemar – a first evaluation. Swedish Nuclear Fuel and Waste Management Co. Stockholm, Sweden. (SKB TR 06-09).
Sun, D.-a., Zhang, Q.-Y., Zhang, L., & Zhu, Z.-C. (2018). Experimental study on ageing effect on shear strength of Gaomiaozi bentonite. Rock and Soil Mechanics, 1191-1196.
Villar, M. (2005). MX-80 Bentonite. Thermo-Hydro-Mechanical Characterisation Performed at CIEMAT in the Context of the Prototype Project. CIEMAT Technical Report.
Ye, W., Lai, X., Wang, Q., Chen, Y., Chen, B., & Cui, Y. (2014). An experimental investigation on the secondary compression of unsaturated GMZ01 bentonite. Applied Clay Science, 97-98, 104-109.
Yong, R. N., Boonsinsuk, P., & Yiotis, D. (1985). Creep Behaviour of a buffer material for nuclear fuel waste vault. Canadian Geotechnical Journal, 22, 541-551.
李冠宏. (2016). 最終處置場近場環境對緩衝材料回脹壓力之影響. 國立中央大學.

指導教授

黃偉慶(Huang Wei-Hsing)

審核日期

2019-1-10

推文