評估不同瀝青混凝土吸音性質與平均紋理深度之研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：25

、訪客IP：3.15.17.25

姓名

方荻妲(Dita Adelafani) 查詢紙本館藏

畢業系所

土木工程學系

論文名稱

評估不同瀝青混凝土吸音性質與平均紋理深度之研究
(Evaluate the Sound Absorption and Mean Profile Depth in Different Asphalt Mixture Design)

相關論文

★ Engineering and Environmental Analysis of Maintenance Interval in Taiwan Freeway -the Case of Guanxi Section	★ 3D 鋪面調查車之驗證與國道應用分析
★ 營建剩餘土石方物流監控及管理系統之建置	★ 透水性鋪面保水與溫差成效之評估 -以中壢市龍慈路為例
★ 以生命週期評估滾筒碴與轉爐石應用於瀝青混凝土之研究	★ 傳統單點雷射與2D雷射應用於平坦度之比較研究
★ 鋪面劣化影像自動辨識應用於鋪面巡查精進研究	★ 自動化鋪面破壞影像辨識系統導入鋪面破壞維護管理系統之研究
★ 以ETC大數據結合FWD建立台灣區高速公路鋪面結構評估準則之研究	★ The Comparison Study of Various Surface Maintenance Alternatives in Taiwan Freeway
★ The Preliminary Study of conducting Pavement Maintenance Model for Taiwan Provincial Highways using Life-Cycle Cost Analysis	★ 冷拌再生瀝青混凝土應用於管線挖掘回填層之可行性研究
★ 台灣現行修補材料運用於柔性鋪面表層裂縫與坑洞修補之耐久性初步探討	★ 以車載藍光雷射建構國道鋪面抗滑值與二維紋理之關聯模型
★ 以不同光譜雷射應用於鋪面平坦度量測之綜合性評估	★ 冷拌再生瀝青混凝土應用於道路管線挖掘回填工程之現地驗證

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

摘要

交通噪音被發現是社會和生活品質中存在問題的領域之一，因為它會導致環境問題而受到更多關注，根據《噪音控制法》等世界範圍內不斷演進的法規，測試場地標準將成為未來車輛和輪胎噪音測試的重要部分，上述可以遵循 ISO 10844:2014 在測試車道上測量行駛的車輛來實現。ISO 10844內指的路面為密級配熱拌瀝青混凝土鋪面，車道吸音係數要求不超過 0.8，平均剖面深度 (Mean Profile Depth, MPD)標準範圍介於0.3 ± 0.2 mm。本研究通過幾種混合料配合設計和實驗室超級鋪面旋轉式壓實機 (Superpave gyratory compactor, SGC) 壓製試體，評估兩種不同細骨料稜角率、三種不同級配和三種不同空隙率對聲學性能和表面紋理性能的影響，測量結果符合ISO 10844對吸音係數和MPD之要求，本研究建議使用粗和中等兩種級配，其吸音係數和MPD皆有滿意的結果，而細級配往往具有較低的MPD。空隙率、級配曲線、細粒料稜角率與吸音係數呈正相關，同時，粗級配曲線是唯一與MPD呈現高度相關性的參數。本研究發現，可能是因為兩種混合物為達到目標空隙率而使用的壓實圈數不同，細骨料稜角率性能顯示出與早期研究相反的結果，因此，它會影響紋理性能。

關鍵詞: 測試道路, 吸音係數, 平均值紋理深度, 配合設計, 細粒料稜角率

摘要(英)

Abstract

Traffic noise is found to be one of the problematic areas in society and quality of life that gained greater attention as it contributes to an environmental problem. According to the Noise Control Act and other regulations worldwide that continue to evolve, test track standard will become an essential element of the vehicle and tire noise testing in the future. Those can be achieved by measuring the driven vehicle on a test track which is following the ISO 10844:2014. An ISO 10844 surface is intended to be a dense-graded hot-mix asphalt pavement with a sound absorption requirement not exceed 0.8 for the drive lane and 0.3 ± 0.2 mm for the mean profile depth (MPD) standard range. This study aimed at evaluating the influence of 2 different fine aggregate angularity, 3 different gradations lies in the ISO 10844 regulation and 3 different air voids through the several mixture designs and the laboratory mixed and compacted specimen using Superpave gyratory compactor (SGC) on the acoustic performance and surface texture performance which represented as sound absorption coefficient and MPD to comply with the ISO 10844 requirement. Coarse gradation and mediocre gradation of both mixtures are recommended as show the satisfaction result on sound absorption and MPD, while the fine gradation tends to have low MPD. Air void, gradation, and fine aggregate angularity are found to be positively correlated with sound absorption. Meanwhile, a moderate correlation between air void and MPD only found at coarse gradation. In this study, the fine aggregate angularity performance shows the opposite result with the earlier findings possibly due to the different gyration number of compactions that the both mixtures get for reaching the air void target; thus, it interfiled the texture performance.
Keywords: Test track, sound absorption, mean profile depth, mixture design, fine aggregate angularity.

關鍵字(中)

★ 測試道路
★ 吸音係數
★ 平均值紋理深度
★ 配合設計
★ 細粒料稜角率

關鍵字(英)

★ Test track
★ sound absorption
★ mean profile depth
★ mixture design
★ fine aggregate angularity

論文目次

Table of Contents

Cover
Abstract i
Acknowledgement iii
Table of Contents iv
List of Figures vi
List of Tables ix
Chapter 1 Introduction 1
1.1. Research Backgrounds 1
1.2. Research Objectives 3
1.3. Research Scopes 3
Chapter 2 Literature Review 4
2.1. Test Track 4
2.1.1 Test Track Section 4
2.1.2 Surface Properties of Test Track 5
2.2. Sound Absorption 6
2.2.1 Factors Affect Sound Absorption 7
2.3. Surface Texture 14
2.3.1 Difference of Mean Profile Depth and Mean Texture Depth 15
2.3.2 Factors Affect Surface Texture 16
2.4. Aggregate Angularity Characteristic on Mixture Performance 21
2.5. Parameters Used for This Research 22
Chapter 3 Methodology 23
3.1. Research Flowchart 23
3.2. Methodology Scope 25
3.3. Material Properties 26
3.3.1 Physical Properties of Aggregate 26
3.3.2 Physical Properties of Asphalt Binder 30
3.4. Experimental Design 30
3.5. Laboratory Performance 31
3.5.1 Maximum Specific Gravity and Density 31
3.5.2 Bulk Specific Gravity 32
3.5.3 Mean Profile Depth 33
3.5.4 Sound Absorption 35
Chapter 4 Result and Discussion 37
4.1. Material Properties 37
4.1.1 Aggregate Physical Properties 37
4.1.2 Asphalt Binder Properties 39
4.2. Experimental Design 40
4.3. Laboratory Performance 42
4.3.1 Sound Absorption Test 42
4.3.2 Mean Profile Depth Test 54
4.3.3 Compaction Performance Between Different Mixtures 66
Chapter 5 Conclusions and Recommendations 72
5.1. Conclusions 72
5.2. Recommendations 73

參考文獻

References

1. Robert Otto Rasmussen, R.J.B., Ulf Sandberg, Eric P. Mun, The Little Book of Quieter Pavements. 2007, Federal Highway Administration: Washington DC.
2. Bernhard, R., et al., An introduction to tire/pavement noise of asphalt pavement. Institute of Safe, Quiet and Durable Highways, Purdue University, 2005.
3. Rasmussen, R. and P. Wiegand. Measuring and Analyzing Pavement Texture Concrete Pavement Surface Characteristics Program. 2011.
4. Wolkesson, M., Evaluation of Impedance Tube Methods A two microphone In-Situ Method for Road Surfaces and The Three Microphone Transfer Function Method for Porous Materials, in Department of Civil and Environmental Engineering. 2012, CHALMERS UNIVERSITY OF TECHNOLOGY: Goteborg, Sweden 2013.
5. Rasmussen, R.O., Designing and Constructing Pavements to Comply with The ISO 10844:2011 Exterior Noise Test Track Standard, in Inter Noise. 2013: Austria.
6. ISO-10844, Specification of Test Track for Measuring Noise Emitted by Road Vehicle and Their Tyres. 2014, ISO: Switzerland.
7. Zhang, H., Z. Liu, and X. Meng, Noise reduction characteristics of asphalt pavement based on indoor simulation tests. Construction and Building Materials, 2019. 215: p. 285-297.
8. Knabben, R.M., et al., Evaluation of sound absorption capacity of asphalt mixtures. Applied Acoustics, 2016. 114: p. 266-274.
9. Chu, L., T.F. Fwa, and K.H. Tan, Evaluation of wearing course mix designs on sound absorption improvement of porous asphalt pavement. Construction and Building Materials, 2017. 141: p. 402-409.
10. Mun, S., Sound absorption characteristics of porous asphalt concrete pavements. Canadian Journal of Civil Engineering, 2010. 37(2): p. 273-278.
11. Lu, Q., P. Fu, and J. Harvey, Laboratory evaluation of the noise and durability properties of asphalt surface mixes. 2009.
12. Guo, Z., et al., Study on the Influential Factors of Noise Characteristics in Dense-Graded Asphalt Mixtures and Field Asphalt Pavements. Shock and Vibration, 2018. 2018: p. 1-13.
13. Ahammed, M.A. and S.L. Tighe, Acoustic Absorption of Conventional Pavements. International Journal of Pavement Research & Technology, 2011. 4(1).
14. 13473-1, I., Characterization of pavement texture by use of surface profiles — Part 1: Determination of mean profile depth. 2019.
15. Plati, C., M. Pomoni, and T. Stergiou, Development of a Mean Profile Depth to Mean Texture Depth Shift Factor for Asphalt Pavements. Transportation Research Record, 2017. 2641(1): p. 156-163.
16. Hanson, D.I. and B.D. Prowell, Evaluation of circular texture meter for measuring surface texture of pavements. 2004, The Center.
17. Henry, J.J., Evaluation of pavement friction characteristics. Vol. 291. 2000: Transportation Research Board.
18. Sandberg, U. and J. Ejsmont, Tyre/road noise. Reference book. 2002.
19. Lin, C. and W. Tongjing, Effect of fine aggregate angularity on skid-resistance of asphalt pavement using accelerated pavement testing. Construction and Building Materials, 2018. 168: p. 41-46.
20. Gao, L., et al., Correction of texture depth of porous asphalt pavement based on CT scanning technique. Construction and Building Materials, 2019. 200: p. 514-520.
21. Ahammed, M.A. and S.L. Tighe, Asphalt pavements surface texture and skid resistance—exploring the reality. Canadian Journal of Civil Engineering, 2012. 39(1): p. 1-9.
22. Masad, E., D. Little, and R. Sukhwani, Sensitivity of HMA performance to aggregate shape measured using conventional and image analysis methods. Road materials and pavement design, 2004. 5(4): p. 477-498.
23. Polaczyk, P., et al., Influence of aggregates angularity on the locking point of asphalt mixtures. Road Materials and Pavement Design, 2019. 20(sup1): p. S183-S195.
24. Topal, A. and B. Sengoz, Evaluation of compacted aggregate resistant test compared with the fine aggregate angularity standards. Construction and Building Materials, 2008. 22(5): p. 993-998.
25. Chen, S.H., et al. Laser scan system to establish 3-d surface texture and predict friction of pavement. in Applied Mechanics and Materials. 2012. Trans Tech Publ.
26. Wolkesson, M., Evaluation of impedance tube methods-A two microphone in-situ method for road surfaces and the three microphone transfer function method for porous materials. 2012.
27. Crocker, M.J., et al., Measurement of acoustical and mechanical properties of porous road surfaces and tire and road noise. Transportation Research Record, 2004. 1891(1): p. 16-22.
28. Cooley, L.A., et al., Bulk specific gravity round-robin using the Corelok vacuum sealing device. 2002, National Center for Asphalt Technology.
29. Goodman, S.N., Y. Hassan, and A.O. Abd El Halim, Preliminary estimation of asphalt pavement frictional properties from superpave gyratory specimens and mix parameters. Transportation research record, 2006. 1949(1): p. 173-180.
30. Khasawneh, M.A. and M.A. Alsheyab, Effect of nominal maximum aggregate size and aggregate gradation on the surface frictional properties of hot mix asphalt mixtures. Construction and Building Materials, 2020. 244: p. 118355.
31. Stakston, A.D., H.U. Bahia, and J.J. Bushek, Effect of fine aggregate angularity on compaction and shearing resistance of asphalt mixtures. Transportation Research Record, 2002. 1789(1): p. 14-24.
32. Rafferty, S.P., Evaluation of the compacted aggregate resistance test. 2004.

指導教授

陳世晃(Shih-Huang Chen)

審核日期

2021-7-12

推文