以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：81

、訪客IP：3.21.159.11

姓名	宋冠賦(Kuan-Fu Sung)  查詢紙本館藏	畢業系所	機械工程學系
論文名稱	兩相微流道蒸發器熱傳性能增強研究 (Experimental Study on Flow Boiling Heat Transfer Enhancement in Microchannel Heat Exchangers)
相關論文	★ 冷卻水溫度與冰水溫度對離心式冰水主機性能影響之實驗分析 ★ 不同結構與幾何形狀對熱管性能之影響 ★ HFC-134a與HFO-1234yf 在板式熱交換器中流動沸騰之性能比較 ★ 油冷卻器熱傳與壓降性能實驗分析 ★ 水對冷媒R22在板式熱交換器內之性能測試分析 ★ 水對水在不同板片型式之板式熱交換器性能測試分析與比較 ★ 油冷卻器性能測試分析與比較 ★ 空調機用水簾式暨光觸媒空氣清淨機 研製及測試 ★ 水對空氣在板式熱交換器之性能測試分析 ★ 板片入出口及入出口管路壓降估計對板式熱交換器壓降性能影響分析 ★ 微熱交換器之設計與性能測試 ★ 板式熱交換器之入出口壓降實驗分析 ★ 液體冷卻系統中之微熱交換器性能分析與改良 ★ 直接模擬蒙地卡羅法於高低速流場之模擬 ★ 液體微熱交換器之熱傳增強研究 ★ 冷媒R22在板式熱交換器內之凝結熱傳及壓降性能實驗分析
檔案	[Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   至系統瀏覽論文 (2025-10-1以後開放)
摘要(中)	近年來，隨著伺服器及電腦工作站的效能快速提升，氣體及液體冷卻系統在未來已無法滿足高端電子產品散熱的應用，兩相蒸發冷卻將成為未來高功率電子設備冷卻之最佳解決方案。然而在應用上，兩相蒸發冷卻在蒸發器中產生氣泡回流及流動不穩定之現象，會使得液體無法補充至流道而造成局部乾涸，影響整體熱傳性能。因此如何解決微流道蒸發器內之汽泡回流成為兩相蒸發冷卻系統是否可實用化的關鍵。本研究透過漸擴流道及微多孔塗層兩種熱傳增強方式，降低氣泡回流現象並提高熱傳性能，製作適用於兩相冷卻系統所需之高性能微流道蒸發器。蒸發器流道型式包含直線雙通、漸擴雙通及直線單通，使用工作流體HFC-245fa並分別對每種蒸發器進行微多孔塗層與否，觀察其前後熱傳性能差異比較。實驗結果顯示在沒有微多孔塗層下之蒸發器以雙通漸擴流道性能表現最佳，其與直線單通蒸發器相比熱傳性能增加了34.2%。從可視化觀察結果顯示漸擴流道在高瓦數時能有效抑制氣泡回流發生，延緩乾涸現象在微流道中發生。當微多孔層塗佈於蒸發器時，因微多孔層內氣泡成核密度增加，使得大量氣泡產生於加熱表面上並帶走大量的熱。在三種微多孔塗層蒸發器中，以單通直線之熱傳系性能表現最好，特別是在塗層厚度為52 m的時候。在微多孔塗佈厚度為98 m時，其熱傳性能增加41% ~ 90%，然而在微多孔塗佈52 m時，其熱傳性能增加65% ~ 148%，且微多孔塗佈對蒸發器壓降影響可以忽略。此兩種熱傳增強方式皆可適用於兩相蒸發冷卻系統，若欲使用表面熱傳增強，則可選擇將微多孔層塗佈於單通直線流道上。若單純使用鰭片製作微流道蒸發器，則可以考慮雙通漸擴流道。
摘要(英)	This study explored the flow boiling heat transfer enhancement using refrigerant HFC-245fa in microchannel heat exchangers. Various heat transfer enhancement techniques were discussed and applied to different flow configurations, including 2-pass diverging microchannel, 2-pass straight microchannel, and 1-pass straight microchannel. The results showed that the 2-pass diverging microchannel heat exchanger without coating exhibited the highest heat transfer performance, displaying a 20% increase in heat transfer compared to other configurations. Visualization techniques were employed to validate these test results. Upon applying a porous coating to the heat exchangers, straight microchannel in both 1-pass and 2-pass configurations showed superior heat transfer performance. A 52 μm coating led to enhancements ranging from 65% to 148% compared to a smooth surface, while a 98 μm coating resulted in enhancements of 41% to 90% across different flow rates. Importantly, porous coating thickness had no significant impact on flow boiling pressure drops. For two-phase cooling systems, it is advisable to use 2-pass diverging microchannel without coating or add a 52 μm porous coating to 1-pass straight microchannel. Porous coating emerges as a highly promising technique for enhancing flow boiling heat transfer in two-phase microchannel heat exchanger.
關鍵字(中)	★ 兩相熱傳 ★ 微流道蒸發器 ★ 微多孔表面 ★ 漸擴流道 ★ 流譜 ★ HFC-245fa	關鍵字(英)	★ Flow boiling heat transfer ★ Microchannel heat exchanger ★ 2-pass diverging ★ Microporous coating ★ Flow pattern ★ HFC-245fa
論文目次	Table of Contents Chinese Abstract i English Abstract ii Table of Contents iii List of Figures vi List of Tables xiii Explanation of Symbols xv Chapter Ⅰ.　Introduction 1 1-1　　Thermal Challenges in IT Industry and Power Electronics 1 1-2　　State-of-the-art in Electronic Cooling 5 1-3　　Heat Transfer Performance and Flow Reversal in Microchannel 10 1-4　　Published Papers on Flow Boiling in Microchannel 12 1-5　　Research Objective 15 Chapter Ⅱ.　Literature Review 16 2-1　　Flow Boiling in Macrochannel and Microchannel 16 2-2　　Bubble Confinement and Flow Reversal Problem 17 2-2-1　Bubble Confinement 17 2-2-2　Flow Reversal Problem 19 2-3　　Flow Boiling Heat Transfer Enhancement 22 2-3-1　Fin Structures 22 2-3-2　Expanding Flow Area 26 2-3-3　Artificial Nucleation Site 33 2-3-4　Porous Coating 36 2-4　　Summary 40 Chapter Ⅲ.　Experimental Method and Apparatus 44 3-1　　Diverging Channel Design and Test Section 44 3-1-1　Diverging Channel Design 44 3-1-2　Test Section (Flow Boiling Experiment) 48 3-1-3　Test Section (Visualization) 52 3-2　　Microporous Coating and Test Section 55 3-3　　Experimental System and Apparatus 59 3-3-1　Experimental System 59 3-3-2　Experimental Apparatus 61 3-3-3　Experimental Procedure 62 Chapter Ⅳ.　Experimental Results and Discussion 66 4-1　　Single-Phase Heat Transfer 67 4-2　　Parallel Straight Microchannel 67 4-2-1　Flow Boiling Heat Transfer 67 4-2-2　Flow Boiling Pressure Drop 69 4-3　　2-pass Straight and Diverging Microchannel 73 4-3-1　Flow Boiling Heat Transfer 73 4-3-2　Comparison of Flow Boiling Heat Transfer 77 4-3-3　Comparison of Flow Boiling Pressure Drop 81 4-4　　Parallel Straight Microchannel (Porous Coating) 84 4-4-1　Flow Boiling Heat Transfer 84 4-4-2　Effect of Coating Layer Thickness on Flow Boiling Heat Transfer 86 4-4-3　Effect of Coating Layer Thickness on Flow Boiling Pressure Drop 91 4-5　　2-pass Straight and Diverging Microchannel (Porous Coating) 93 4-5-1　Flow Boiling Heat Transfer 93 4-5-2　Comparison of Flow Boiling Heat Transfer and Pressure Drop 97 4-5-3　Comparison of Coating and Non-Coating 101 4-6　　Comparison of Thermal Performance in All Heat Exchangers 108 Chapter Ⅴ.　Flow Visualization Results and Discussion 118 5-1　　2-pass Heat Exchangers 118 5-1-1　Definition of Flow Patterns 118 5-1-2　Effect of Flow Rates on Diverging Microchannel 119 5-1-3　Flow Pattern Differences and Related Heat Transfer Performance 127 5-2　　Characteristic of Bubble Flow Reversal Behavior 133 5-2-1　Number of Flow Reversal Channels 134 5-2-2　Flow Reversal Distribution 137 5-3　　2-pass Coating Heat Exchangers 140 5-3-1　Number of Flow Reversal Channels 140 5-3-2　Flow Reversal Distribution 143 Chapter Ⅵ.　Conclusion 146 Bibliography 147 Appendix Ⅰ.　Bubble Flow Reversal in a Microchannel 155 Appendix Ⅱ.　Microporous Coating Fabrication 161 Appendix Ⅲ.　The Uncertainties of the Experimental Apparatus 163 Appendix Ⅳ.　The Uncertainty Analysis of the Experimental Data 169
參考文獻	[1] C. Qian, A.M. Gheitaghy, J. Fan, H. Tang, B. Sun, H. Ye and G. Zhang, “Thermal management on IGBT power electronic devices and modules,” IEEE Access, Vol. 6, January 2018, pp. 12868-12884. [2] L.T. Yeh, “Review of heat transfer technologies in electronic equipment,” ASME Journal of electronic packaging, Vol. 117, December 1995, pp. 333-339. [3] “Heterogeneous Integration Roadmap Chapter 2: High Performance Computing and Data Centers,” November 2021, adapted from: https://eps.ieee.org/images/files/HIR_2021/ch02_hpc.pdf [4] “NVIDIA announces CPUs designed for large-scale artificial intelligence and high-performance computing workloads,” April 2021, adapted from: https://blogs.nvidia.com.tw/2021/04/13/nvidia-announces-cpu-for-giant-ai-and-high-performance-computing-workloads/ [5] “Intel 14th Gen CPUs Allegedly Launching on 17th October: Core i9-14900K at 6GHz,” September 2023, adapted from: https://www.hardwaretimes.com/intel-14th-gen-cpus-allegedly-launching-on-17th-october-core-i9-14900k-at-6ghz/ [6] C. Bachmann and A. Bar-Cohen, “Hotspot remediation with anisotropic thermal interface materials,” 11th Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, Orlando, FL, USA, May 2008, pp. 238-247. [7] J. Zhang, S. Sadiqbatcha, M. O’Dea, H. Amrouch and S.D.X. Tan, “Full-chip power density and thermal map characterization for commercial microprocessors under heat sink cooling,” IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems, Vol. 41, June 2021, pp. 1453-1466. [8] “Heterogeneous Integration Roadmap Chapter 20: Thermal,” November 2021, adapted from: https://eps.ieee.org/images/files/HIR_2021/ch20_thermal1.pdf [9] C. Qian, A.M. Gheitaghy, J. Fan, H. Tang, B. Sun, H. Ye and G. Zhang, “Thermal management on IGBT power electronic devices and modules,” IEEE Access, Vol. 6, January 2018, pp. 12868-12884. [10] T.A. Burress, C.L. Coomer, S.L. Campbell, L.E. Seiber, L.D. Marlino, R.H. Staunton and J.P. Cunningham, “Evaluation of the 2007 Toyota Camry hybrid synergy drive system,” Oak Ridge National Lab, Oak Ridge, USA, April 2008, pp. 1-102. [11] R.G. Mertens, L. Chow, K.B. Sundaram, R.B. Cregger, D.O. Rini, L. Turek and B.A. Saarloos, “Spray cooling of IGBT devices,” ASME Journal of Electronic Packaging, Vol. 129, September 2007, pp. 316-323. [12] E.M. Dede, “Thermal packaging challenges for next generation power electronics,” Applied Power Electronics Conference, New Orleans, USA, March 2020, pp. 1-27. [13] “Two-Phase Evaporative Precision Cooling Systems For heat loads from 3 to 300 kW,” November 2011, adapted from: https://www.parker.com/content/dam/Parker-com/Literature/CIC-Group/Precision-Cooling/New-literature/Two_Phase_Evaporative_Precision_Cooling_Systems.pdf [14] Adopted from: https://www.1-act.com/resources/learning-center/pumped-two-phase/ [15] G. Hetsroni, A. Mosyak, Z. Segel and G. Ziskind, “A uniform temperature heat sink for cooling of electronic devices,” International Journal of Heat and Mass Transfer, Vol. 45, January 2002, pp. 3275-3286. [16] M.E. Steinke and S.G. Kandlikar, “An experimental investigation of flow boiling characteristics of water in parallel microchannel,” ASME Journal of heat transfer, Vol. 126, August 2004, pp. 518-526. [17] J. Lee and I. Mudawar, “Fluid flow and heat transfer characteristics of low temperature two-phase micro-channel heat sinks – Part 1: Experimental methods and flow visualization results,” International Journal of Heat and Mass Transfer, Vol. 51, May 2008, pp. 4315-4326. [18] W. Qu and I. Mudawar, “Transport phenomenon on two-phase micro-channel heat sinks,” ASME Journal of Electronic Packaging, Vol. 126, May 2004, pp. 213-224. [19] D.B. Tuckerman and R.F.W. Pease, “High-performance heat sinking for VLSI,” IEEE Electron device letters, Vol. 2, May 1981, pp. 126-129. [20] G.M. Lazarek and S.H. Black, “Evaporative heat transfer, pressure drop and critical heat flux in a small vertical tube with R-113,” International Journal of Heat and Mass Transfer, Vol. 25, July 1982, pp. 945-960. [21] M.M. Shah, “A generalized graphical method for predicting CHF in uniformly heated vertical tubes,” International Journal of Heat and Mass Transfer, Vol. 22, April 1979, pp. 557-568. [22] K. Moriyama, A. Inoue and H. Ohira, “The thermohydraulic characteristics of two-phase flow in extremely narrow channels (the frictional pressure drop and heat transfer boiling two-phase flow, analytical model),” Heat Transfer-Japanese Research; (United States), Vol. 21, September 1993, pp. 105-111. [23] X.F. Peng and B.X. Wang, “Forced convection and flow boiling heat transfer for liquid flowing through microchannel,” International Journal of Heat and Mass Transfer, Vol. 36, January 1993, pp. 3421-3427. [24] L. Jaing, M. Wong and Y. Zohar, “Phase change in microchannel heat sinks with integrated temperature sensors,” Journal of microelectromechanical systems, Vol. 8, December 1999, pp. 358-365. [25] K. Cornwell and P.A. Kew, “Boiling in small parallel channels,” Proceedings of CEC Conference on Energy Efficiency in Process Technology, Athens, October 1992, pp. 624-638. [26] K.E. Kasza, T. Didascalou and M.W. Wambsganss, “Microscale flow visualization of nucleate boiling in small channels: mechanisms influencing heat transfer,” No. ANL/ET/CP-92073; CONF-9706130-2. Argonne National Lab.(ANL), Argonne, IL (United States), July 1997. [27] G. Hetsroni, A. Mosyak, Z. Segal and E. Pogrebnyak, “Two-phase flow patterns in parallel micro-channels,” International Journal of Multiphase Flow, Vol. 29, March 2003, pp. 341-360. [28] H.Y. Li, F.G. Tseng and C. Pan, “Bubble dynamics in microchannel. Part II: two parallel microchannel,” International Journal of Heat and Mass Transfer, Vol. 47, December 2004, pp. 5591-5601. [29] P. Balasubramanian and S.G. Kandlikar, “Experimental study of flow patterns, pressure drop, and flow instabilities in parallel rectangular minichannels,” Heat Transfer Engineering, Vol. 26, 2005, pp. 20-27. [30] L. Yin, L. Jia, P. Guan and D. Liu, “Experimental investigation on bubble confinement and elongation in microchannel flow boiling,” Experimental thermal and fluid science, Vol. 54, January 2014, pp. 290-296. [31] L. Jaing, M. Wong and Y. Zohar, “Forced convection boiling in a microchannel heat sink,” Journal of microelectromechanical systems, Vol. 10, March 2001, pp. 80-87. [32] K.H. Chang and C. Pan, “Two-phase flow instability for boiling in a microchannel heat sink,” International Journal of Heat and Mass Transfer, Vol. 50, January 2007, pp. 2078-2088. [33] B. Markal, O. Aydin and M. Avci, “Effect of hydraulic diameter on flow boiling in rectangular microchannel,” Heat and Mass Transfer, Vol. 55, April 2019, pp. 1033-1044. [34] A.H. Al-Zaidi, A.H. Mahmound and T.G. Karayiannis, “Effect of aspect ratio on flow boiling characteristics in microchannel,” International Journal of Heat and Mass Transfer, Vol. 164:120587, January 2021. [35] S.G. Kandlikar, “Nucleation characteristics and stability considerations during flow boiling in microchannel,” Experimental Thermal and Fluid Science, Vol. 30, May 2006, pp. 441-447. [36] S. Krishnamurthy and Y. Peles, “Flow boiling of water in a circular staggered micro-pin fin heat sink,” International Journal of Heat and Mass Transfer, Vol. 51, March 2008, pp. 1349-1364. [37] W. Qu and A. Siu-Hio, “Experimental study of saturated flow boiling heat transfer in an array of staggered micro-pin-fins,” International Journal of Heat and Mass Transfer, Vol. 52, March 2009, pp. 1853-1863. [38] W. Qu and A. Siu-Hio, “Measurement and prediction of pressure drop in a two-phase micro-pin-fin heat sink,” International Journal of Heat and Mass Transfer, Vol. 52, October 2009, pp. 5173-5184. [39] A. Reeser, A. Bar-Cohen and G. Hetsroni, “High quality flow boiling heat transfer and pressure drop in microgap pin fin arrays,” International Journal of Heat and Mass Transfer, Vol. 78, November 2014, pp. 974-985. [40] Y. Zhu, D.S. Antao, K.H. Chu, S. Chen, T.J. Hendricks, T. Zhang, and E.N. Wang, “Surface structure enhanced microchannel flow boiling,” ASME Journal of Heat Transfer, Vol. 138:091501, September 2016, pp. 1-13. [41] Y. Zhu, D.S. Antao, K.H. D.W. Bian, S. R. Rao, J.D. Sircar, T. Zhang, and E.N. Wang, “Suppressing high-frequency temperature oscillations in microchannel with surface structures,” Applied Physics Letters, Vol. 110:033501, January 2017, pp. 1-6. [42] M. Law, P.S. Lee and K. Balasubramanian, “Experimental investigation of flow boiling heat transfer in novel oblique-finned microchannel,” International Journal of Heat and Mass Transfer, Vol. 76, September 2014, pp. 419-431. [43] M. Law and P.S. Lee, “A comparative study of experimental flow boiling heat transfer and pressure characteristic in straight- and oblique-finned microchannel,” International Journal of Heat and Mass Transfer, Vol. 85, June 2015, pp. 797-810. [44] Y.K. Prajapati, M. Pathak and M.K. Klan, “A comparative study of flow boiling heat transfer in three different configurations of microchannel,” International Journal of Heat and Mass Transfer, Vol. 85, June 2015, pp. 711-722. [45] A. Mukherjee and S.G. Kandlikar, “Numerical study of the effect of inlet constriction on bubble growth during flow boiling in microchannel,” 3rd International Conference on Microchannel and Minichannels, Toronto, Ontario, Cnada, June 13-15, 2005, pp. 73-80. [46] C. Pan, and C.T. Liu, “Bubble dynamics for convective boiling in silicon-based, converging and diverging microchannel,” 13th International Heat Transfer Conference, Kensington, NSW, Australia, August 2006, p. 11. [47] P.C Lee, and C. Pan, “Boiling heat transfer and two-phase flow of water in a single shallow microchannel with a uniform or diverging cross section,” Journal of Micromechanics and Microengineering, Vol. 18, 025005, December 2007. [48] C.T. Lu and C. Pan, “Stabilization of flow boiling in microchannel heat sinks with a diverging cross-section design,” Journal of Micromechanics and Microengineering, Vol. 18, 075035, May 2008. [49] K. Balasubramanian, P.S. Lee, L.W. Jin, S.K. Chou, C.J. Teo and S. Gao, “Experimental investigations of flow boiling heat transfer and pressure drop in straight and expanding microchannel - A comparative study,” International Journal of Thermal Science, Vol. 50, July 2011, pp. 2413-2421. [50] Balasubramanian, P.S. Lee, C.J. Teo and S.K. Chou, “Flow boiling heat transfer and pressure drop in stepped fin microchannel,” International Journal of Heat and Mass Transfer, Vol. 67, August 2013, pp. 234-252. [51] G. Kandlikar, T. Widger, A. Kalani and V. Mejia, “Enhanced flow boiling over open microchannel with uniform and tapered gap manifolds,” ASME Journal of Heat Transfer, Vol. 135, 061401, June 2013. [52] Kalani and S.G. Kandlikar, “Evaluation of pressure drop performance during enhanced flow boiling in open microchannel with tapered manifolds”, ASME Journal of Heat Transfer, Vol. 136, 051502, May 2014. [53] Recinella and S.G. Kandlikar, “Enhanced flow boiling using radial open microchannel with manifold and offset strip fins,” ASME Journal of Heat Transfer, Vol. 140, 021502, February 2018. [54] S. Hong, C. Dang and E. Hihara, “Experimental investigation on flow boiling in radial expanding minichannel heat sinks applied for low flow inertia condition,” International Journal of Heat and Mass Transfer, Vol. 143, 118588, August 2019. [55] S. Hong, C, Dang, and E. Hihara, “Experimental investigation on flow boiling characteristics of radial expanding minichannel heat sinks applied for two-phase flow inlet,” International Journal of Heat and Mass Transfer, Vol. 151, 119316, January 2020. [56] X. Jiang, S. Zhang, Y. Li and C. Pan, “High performance heat sink with counter flow diverging microchannel,” International Journal of Heat and Mass Transfer, Vol. 116, 120344, August 2020. [57] X. Jiang, S. Zhang, Y. Li, Z. Wang and C. Pan, “Achieving ultra-high coefficient of performance of two-phase microchannel heat sink with uniform void fraction,” International Journal of Heat and Mass Transfer, Vol. 184, 122300, March 2022. [58] A. Koşar, C.J. Kuo and Y. Peles, “Boiling heat transfer in rectangular microchannel with reentrant cavities,” International Journal of Heat and Mass Transfer, Vol. 48, April 2005, pp. 4867-4886. [59] C.J. Kuo, A. Koşar, Y. Peles, S. Virost, C. Mishra and M.K. Jensen, “Bubble dynamics during boiling in enhanced surface microchannel,” Journal of Microelectromechanical systems, Vol. 15, December 2006, pp. 1514-1527. [60] S.G. Kandlikar, W.K. Kuan, D.A. Willistein and J. Borrelli, “Stabilization of flow boiling in microchannel using pressure drop elements and fabricated nucleation sites”, ASME Journal of Heat Transfer, Vol. 128, April 2006, pp. 389-396. [61] J. Zhou, X. Luo, Y. Pan, D. Wang, J. Xiao, J. Zhang and B. He, “Flow boiling heat transfer coefficient and pressure drop in minichannels with artificial activation cavities by direct metal laser sintering,” Applied Thermal Engineering, Vol. 160, 113837, September 2019. [62] J.Y. Chang and S.M. You, “Boiling heat transfer phenomenon from microporous and porous surfaces in saturated FC-72,” International Journal of Heat and Mass Transfer, Vol. 40, November–December 1997, pp. 4437-4447. [63] C.Y. Yang and C.F. Liu, “Effect of coating layer thickness for boiling heat transfer on micro porous coated surface in confined and unconfined spaces,” Experimental Thermal and Fluid Science, Vol. 47, May 2013, pp. 40-47. [64] H. Lee, T. Maitra, J. Palko, D. Kong, C. Zhang, M.T. Barako, Y. Won, M. Asheghi and K.E. Goodson, “Enhanced heat transfer using microporous copper inverse opals,” ASME Journal of Electronic Packaging, Vol. 140, 020906, June 2018. [65] C.N. Ammerman and S.M. You, “Enhancing small-channel convective boiling performance using a microporous surface coating,” ASME Journal of Heat Transfer, Vol. 123, October 2001, pp. 976-983. [66] Y. Sun, L. Zhang, H. Xu and X. Zhong, “Subcooled flow boiling heat transfer from microporous surfaces in a small channel,” International Journal of Thermal Sciences, Vol. 50, June 2011, pp. 881-889. [67] P. Bai, T. Tang and B. Tang, “Enhanced flow boiling in parallel microchannel with metallic porous coating,” Applied Thermal Engineering, Vol. 58, September 2013, pp. 291–297. [68] T. Semenic and S.M. You, “Two-phase heat sinks with microporous coating,” Heat Transfer Engineering, Vol. 34, March 2012, pp. 246-257. [69] V.Y.S. Lee, G. Henderson, A. Reip and T.G. Karayiannis, “Flow boiling characteristics in plain and porous coated microchannel heat sinks,” International Journal of Heat and Mass Transfer, Vol. 183, 122152, February 2022. [70] Fritz, “Berechnung des maximalvolume von dampfblasen,” Physikalische Zeitschrift, Vol. 36, 1935, pp. 379-384. [71] N.J. English and S.G. Kandlikar, “An experimental investigation into the effect of surfactants on air-water two-phase flow in minichannels,” Heat Transfer Engineering, Vol. 27, August 2006, pp. 99-109. [72] J.P. O’connor, J.P. and S.M. You, “A painting technique to enhance pool boiling heat transfer in saturated FC-72,” ASME Journal of Heat and mass Transfer, Vol. 117, May 1995, pp. 387-393. [73] C.Y. Yang and C.F Fan, “Pool boiling of refrigerants R-134a and R-404A on porous and structured surface tubes – Part II. heat transfer performance,” Journal of Enhanced Heat Transfer, Vol. 13, 2006, pp. 85-97. [74] E.W. Lemmon, I.H. Bell, M.L. Huber and M.O. McLinden, “NIST standard reference database 23: reference fluid thermodynamic and transport properties-REFPROP, Version 10.0,” National Institute of Standards and Technology, Standard Reference Data Program, Gaithersburg, 2018. [75] P.S. Lee and S.V Garimella, “Thermally developing flow and heat transfer in rectangular microchannel of different aspect ratios,” International Journal of Heat and Mass Transfer, Vol. 49, August 2006, pp. 3060-3067. [76] L. Sun, and K. Mishima, “An evaluation of prediction methods for saturated flow boiling heat transfer in mini-channels,” International Journal of Heat and Mass Transfer, Vol. 52, November 2009, pp. 5323-5329. [77] S.M. Kim and I. Mudawar, “Universal approach to predicting saturated flow boiling heat transfer in mini/micro-channels – part II. two-phase heat transfer coefficient,” International Journal of Heat and Mass Transfer, Vol. 64, September 2013, pp. 1239-1256. [78] G.F. Hewitt, H.A. Kearsey, P.M.C. Lacey and D.J Pulling, “Burnout and nucleation in climbing film boiling flow,” International Journal of Heat and Mass Transfer, Vol. 8, May 1965, pp. 793-814. [79] C.F. Liu and C.Y. Yang, “Effect of space distance for boiling heat transfer on micro porous coated surface in confined space,” International Journal of Heat and Mass Transfer, Vol. 50, October 2013, pp. 163-171. [80] D. Chisholm, “Two-phase flow in heat exchangers and pipelines,” Heat Transfer Engineering, Vol. 6, 1982, pp. 48-57. [81] S.J. Kline and F.A. McClintock, “Describing uncertainties in single-sample experiments,” Mechanical Engineering, Vol. 75, January 1953, pp. 3-8.
指導教授	楊建裕(Chien-Yuh Yang)	審核日期	2024-4-29
推文	facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu
網路書籤	Google bookmarks   del.icio.us   hemidemi   myshare