中大機構典藏-NCU Institutional Repository-提供博碩士論文、考古題、期刊論文、研究計畫等下載:Item 987654321/54620
English  |  正體中文  |  简体中文  |  全文笔数/总笔数 : 80990/80990 (100%)
造访人次 : 41267255      在线人数 : 435
RC Version 7.0 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜寻范围 查询小技巧:
  • 您可在西文检索词汇前后加上"双引号",以获取较精准的检索结果
  • 若欲以作者姓名搜寻,建议至进阶搜寻限定作者字段,可获得较完整数据
  • 进阶搜寻


    jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/54620


    题名: 可同步優化低壓降線性穩壓器與其誤差放大器的自動化設計方法;Simultaneous Optimization Approach for Low Dropout Regulator and Its Error Amplifier
    作者: 朱冠銘;Chu,Kuan-ming
    贡献者: 電機工程研究所
    关键词: 自動化設計;低壓降線性穩壓器;LDO;low dropout regulator
    日期: 2012-08-21
    上传时间: 2012-09-11 18:55:30 (UTC+8)
    出版者: 國立中央大學
    摘要: 在系統單晶片(System on chip, SoC)的設計中,將不同功能的類比、數位或是射頻電路都整合在一顆晶片內,每個區塊電路所需要的電壓往往都不一樣,系統單晶片的供應電源往往是單一電壓,於是就需要電壓轉換器來將供應電源轉換成每塊電路需要的供應電壓。有著低功率、輸出漣波電壓很小、抗雜訊等優點的低壓降線性穩壓器就常常被應用在轉換電壓上。本論文提出一套低壓降線性穩壓器自動化設計的流程,依靠非線性規劃(Nonlinear programming)、gm/ID的設計概念以及電壓驅動的方法改善傳統幾何演算法的精準度以及效率。誤差放大器(Error amplifier)和低壓降線性穩壓器可以在自動化流程中同時做互相考慮以及最佳化的動作,使整體電路的成本減少。整個流程以Matlab和Hspice來實現,並整合成一個完整的程式。從實驗數據跟傳統的幾何演算法設計流程做個比較,本論文所提出的方法,可以提高公式精準度,同時更可以在相同的規格下,在短時間內找出優於傳統幾何演算法的電路設計。In typical SoC (System on chip, SoC) designs, analog, digital and RF circuits are integrated in a single chip. Because the supply voltage of each circuit block may not the same, voltage converters are often required to generate the required supply voltage of each block from the outside power source. Due to its low power, small ripple and low noise properties, low-dropout linear regulators (LDO) are often used in SoC chips. This thesis proposes a design automation process for optimal sizing of low dropout linear regulator. Based on the nonlinear programming and gm/ID design concept, a bias-driven methodology is adopted to improve the accuracy and efficiency of the traditional approach based on geometric programming. The device in the low dropout linear regulator and its error amplifier are both considered in the optimization process for reducing the overall circuit cost. The proposed automation process has been implemented with Matlab and Hspice. As demonstrated in the experiments, the proposed approach can achieve the required specifications with the shortest computation time and the lowest hardware cost compared to previous approaches.
    显示于类别:[電機工程研究所] 博碩士論文

    文件中的档案:

    档案 描述 大小格式浏览次数
    index.html0KbHTML668检视/开启


    在NCUIR中所有的数据项都受到原著作权保护.

    社群 sharing

    ::: Copyright National Central University. | 國立中央大學圖書館版權所有 | 收藏本站 | 設為首頁 | 最佳瀏覽畫面: 1024*768 | 建站日期:8-24-2009 :::
    DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 隱私權政策聲明