從模流到結構的集成分析光學鏡片之模仁變形研究;Integrating injection molding simulation and structural analysis in the die core of optical lenses

NCU Institutional Repository > 工學院 > 機械工程研究所 > 博碩士論文 > Item 987654321/84311

請使用永久網址來引用或連結此文件: http://ir.lib.ncu.edu.tw/handle/987654321/84311

題名:	從模流到結構的集成分析光學鏡片之模仁變形研究;Integrating injection molding simulation and structural analysis in the die core of optical lenses
作者:	蔡承詣;Tsai, Cheng-Yi
貢獻者:	機械工程學系
關鍵詞:	射出成型;光學鏡片;Moldex3D模流分析;收斂性分析;ABAQUS結構分析;模仁變形;Injection molding;Optical lens;Moldex3D;Convergence analysis;ABAQUS;Die core deformation
日期:	2020-07-22
上傳時間:	2020-09-02 19:01:42 (UTC+8)
出版者:	國立中央大學
摘要:	網格搭建在有限元素分析中為重要的技術，直接影響模擬的準確度和計算效率，因此本研究建立 Type A、 Type B、 Type C三種不同網格定義針對模擬結果與實際短射照片、光程差分佈照片比較，來驗證模型準確度，從研究結果得知， Type C定義可獲得較正確的模流分析結果。透過收斂性分析，另外建立 Type C_1~6不同尺寸的網格進行模擬與實驗的比對，得知介於 Type C_2~4的可獲得較正確的模流分析結果；藉由 Moldex3D模流分析手法進行與實際射出機的響應曲線比較趨勢和結果，以此驗證方法取得最終適合的網格和貼近實際結果的成型條件給後續的模仁變形當初始設定條件。為了探討模仁因溫度歷程受到變形之下鏡片的厚度收縮趨勢和模仁變形趨勢，本研究使用 Moldex3D的 FEA模組匯出模仁至 ABAQUS結構變形上所需的資料進行探討，從結果顯示，對於光學鏡片考慮了模仁變形確實有較大的線收縮率。;Mesh construction is an important technique, which directly affects the accuracy and calculation efficiency of simulation. Therefore, This study established three different meshes type A , B , C. The simulation results are compared with actual short-shot photos and optical retardation distribution photos to validate the accuracy of the model. The results show that the grid size of the narrowest lens thickness area type C at the connection gate can obtain mold flow results more accurately. Through convergence analysis, different sizes grids of were type C_1~6 also established to compare simulation with experiments. We know that the mesh size in type C_2~4 can obtain mold flow results more accurately. Furthermore, Moldex3D mold flow analysis compares and verifies the trends and results of actual machine response curves. With this verification approach, the adequate mesh and the molding conditions close to the experimental results are determined to set the conditions for the subsequent die-core deformation. In order to investigate the thickness shrinkage of the lens and the deformation of the die core due to the temperature changing, Moldex3D FEA module is employed to export the results into ABAQUS structural analysis of die core. Considering the deformation of the die core, the optical lens does have a large linear shrinkage rate.
顯示於類別:	[機械工程研究所] 博碩士論文

文件中的檔案:

檔案	描述	大小	格式	瀏覽次數
index.html		0Kb	HTML	78	檢視/開啟

在NCUIR中所有的資料項目都受到原著作權保護.

社群 sharing

資料載入中.....