人工粒料作為路基材料及CLSM對RC構件和金屬腐蝕之影響研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：33

、訪客IP：18.219.192.243

姓名

呂劭君(Shao-gin Lu) 查詢紙本館藏

畢業系所

土木工程學系

論文名稱

人工粒料作為路基材料及CLSM對RC構件和金屬腐蝕之影響研究
(artificial aggregates used as foundation materials and as aggregates in CLSM cause corrosion of metal materials and reinforced concrete.)

相關論文

★ 水泥製程於資源再利用之研究	★ 焚化底渣水洗前處理及應用之探討
★ 鈦鐵礦氯化爐碴應用於道路基底層及礦尾渣水洗前處理之研究	★ 水洗礦尾渣造粒後之粒料特性探討
★ 水洗礦尾渣取代水泥製品中細粒料之可行性研究	★ 陶瓷業無機性污泥資源化用於人工細粒料及自充填混凝土之研究
★ 磚製品中摻配鈦砂之較佳配比研究	★ 單維電化學傳輸陽離子技術抑制混凝土ASR之研究
★ 不同醇類製備聚丙烯酸酯應用於水泥基材的行為研究	★ 經高溫製程產生含矽再生粒料之鹼質活性研究
★ 改質人工粒料的應用策略基礎研究	★ 爐碴作為混凝土細粒料的膨脹安定化方法及檢測技術研究
★ 鎂鋁氧化物及類水滑石對氯離子吸附行為之研究	★ 以CFB副產石灰作為水淬爐石粉激發劑之可行性探討
★ 加速鋰離子傳輸技術中不同電極間距對離子傳輸行為的影響研究	★ 改質人工粒料取代天然細粒料對混凝土性質的影響

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

本研究探討人工粒料作為路基材料，及作為CLSM粒料時，對金屬材料及混凝土內鋼筋腐蝕的影響，研究內容分為歐盟管柱溶出試驗、鹽水浸漬試驗、NIST程式分析混凝土擴散係數及現地模擬實作。
研究成果顯示：(1)針對人工粒料進行歐盟管柱溶出試驗，分析6種重金屬溶出量，皆低於荷蘭標準及國內環保署土壤重金屬污染標準。(2) NIST程式分析與90天鹽水浸漬試驗對混凝土210及280 kgf/cm2 配比結果比較，顯示NIST程式對於210配比擴散係數的預測較為接近，而對於280配比則有低估的情形。(3)人工粒料級配內之各種防蝕處理碳鋼棒，經埋置五個月後，以熱浸鍍鋅及環氧鋅漆碳鋼棒之重量損失，小於天然級配內相同處理之碳鋼棒，其重量損失肇因於防蝕處理之重量差，為實驗誤差。(4)埋於現地不同路基材料及CLSM溝渠內模擬RC構件，經五個月後並無氯離子滲入混凝土內部且無失去鹼性保護環境，鑿取後之鋼筋與製作RC試體前之鋼筋，其降伏強度、抗拉強度及鋼筋伸長率無太大落差，且皆符合CNS 560規範要求。

摘要(英)

In this study, artificial aggregates used as foundation materials, and as aggregates in CLSM, cause corrosion of metal materials and reinforced concrete. The study includes the EU column leaching test, ponding test, calculating the diffusion coefficient of concrete with the NIST program, simulation practice in situ.
The results: (1) Artificial aggregates for column leaching test, analysis of six leaching of heavy metals, are lower than the Dutch standard and heavy metal pollution of EPA standards. (2) The results of concrete design mixture 210 and 280 kgf/cm2 with NIST program and 90 days of ponding test, NIST program shows the prediction for the diffusion coefficient of 210 kgf/cm2 design mixture is close, but for the 280 kgf/cm2 design mixture is underestimated. (3) A variety of corrosion prevention of carbon steel in artificial aggregate gradation, after five months the weight loss of the hot-dip galvanized and epoxy zinc painted carbon steels, less than the same treatment in the natural gradation, because the weight difference dealing with corrosion, resulting in weight loss for the experimental error. (4) RC components in the different foundation materials and CLSM after five months, no chloride ions penetrate the internal and not lose the basic protection of the environment, the reinforced after cutting and before making RC components, their yield strength, tensile strength and elongation were similar, and they all consistent with CNS 560.

關鍵字(中)

★ 重金屬溶出
★ 鹽水浸漬試驗
★ 腐蝕

關鍵字(英)

★ ponding test
★ leaching of heavy metals
★ corrosion.

論文目次

摘要 I
Abstract I
目錄 i
圖目錄 v
表目錄 ix
第一章緒論 1
1-1 研究緣起及目的 1
1-2 研究內容 2
1-2-1 實驗室分析 2
1-2-2 現地實際模擬試驗 3
第二章文獻回顧 4
2-1 人工粒料之概述 4
2-1-1 礦渣之基本性質 4
2-1-2 人工粒料之基本性質 6
2-2 人工粒料應用於道路基底層之分析 8
2-3 地下金屬管線種類 9
2-4 鋼筋混凝土之腐蝕劣化探討 11
2-4-1 鋼筋之腐蝕機理 11
2-4-2 氯離子的來源及存在型態 12
2-4-3 氯離子於混凝土中傳輸途徑與機制 14
2-4-4 孔隙結構與滲透性 15
2-4-5 氯離子擴散係數 17
2-5 鹽水浸漬試驗 19
2-6 腐蝕量測 19
2-7 表面防蝕處理 21
2-8 重金屬溶出試驗 22
2-9 NIST程式概述 25
第三章研究方法 26
3-1 研究流程 26
3-2 試驗編號 30
3-3 試驗材料及設備 33
3-3-1 試驗材料 33
3-3-2 試驗設備 36
3-4 試驗方法及步驟 38
3-4-1 實驗室分析 38
3-4-2 現地模擬實作 43
第四章研究成果分析 53
4-1 實驗室試驗與現地模擬實作相關性 53
4-2 管柱溶出試驗 54
4-3 鹽水浸漬試驗 61
4-3-1 氯離子擴散的深度及含量 61
4-3-2 氯離子在混凝土中的擴散係數 64
4-4 現地模擬實作 67
4-4-1 現地開挖過程 68
4-4-2 混凝土圓柱試體硝酸銀-比色法 73
4-4-3 金屬材料 76
4-4-4 模擬鋼筋混凝土構件 88
4-5 NIST程式輔助預測本研究混凝土的Cl－擴散係數的可行性 96
第五章結論與建議 98
5-1 結論 98
5-1-1 實驗室分析 98
5-1-2 現地模擬實作 98
5-2 建議 100
參考文獻 102

參考文獻

1. 雷揚中，「焚化爐底碴應用於道路工程之研究」，國立中央大學土木工程研究所碩士論文，2004。
2. 營建署全球資訊網，http://www.cpami.gov.tw/。
3. 林賢正，「鋼筋混凝土之腐蝕行為探討」，中華大學土木工程研究所碩士論文，2002。
4. 陳桂清、饒正、柯正龍、張道光、羅建明，「港灣構造物檢測與耐久性試驗研究」，交通部運輸研究所，2003。
5. 吳文斌，「鋼筋混凝土腐蝕耐久性量測技術之研究」，國立海洋大學材料工程研究所碩士論文，1999。
6. 江明鴻，「混凝土氯離子滲透行為與腐蝕特性之研究」，國立海洋大學材料工程研究所碩士論文，1999。
7. J. N. Enevoldsen, C. M. Hansson, and B.B. Hope, “Binding of chloride in mortar containing admixed or penetrated chlorides,”Cement and Concrete Research, Vol. 24, Issue 8, pp. 1525-1533, 1994.
8. C. Arya, N. R. Buenfeld, and J. B. Newman, “Factors Influencing Chloride-Binding in Concrete,”Cement and Concrete Research, Vol. 20, Issue 2, pp. 291-300, 1990.
9. X. Wu, L. Xu, Q. Yang, and S. Huang, “The diffusion equation of chloride ions in cement mortar,”Trans Shanghai Building Materials Collection, vol. 4, pp. 364-372, 1991.
10. B. F. Johannesson, “Diffusion of a mixture of cations and anions dissolved in water,”Cement and Concrete Research, Vol. 29, Issue 8, pp. 1261-1270, 1999.
11. A. M. Brandt, “Cement-based Composites：Mechanical Properties and Performance,”E& FN SPON, pp. 116-119, 1995.
12. R. Kumar, and B. Bhattacharjee, “Porosity, pore size distribution and in situ strength of concrete,”Cement and Concrete Research, Vol. 33, Issue 1, pp. 155-164, 2003.
13. C. Kok Seng, and Z. Min-Hong, “Water permeability and chloride penetrability of high-strength lightweight aggregate concrete,”Cement and Concrete Research, Vol. 32, Issue 4, pp. 639-645, 2002.
14. J. Crank, “The mathematics of diffusion,”Second Edition, pp. 1-10, 1959.
15. P.S. Mangat, and Kribanandan Gurusamy, “Chloride diffusion in steel fiber reinforced marine concrete,”Cement and Concrete Research, Vol. 17, Issue 3, pp. 385-396, 1987.
16. P.S. Mangat, and Kribanandan Gurusamy, “Chloride diffusion in steel fiber reinforced concrete containing PFA,”Cement and Concrete Research, Vol. 17, Issue 3, pp. 640-650, 1987.
17. AASHTO T259-80, “Resistance of Concrete to Chloride Ion Penetration American Association of States Highway and Transportation Officials,” Standard Specifications-Part II, Tests, Washington, DC, 1990.
18. J. Arsenault, J. P. Bigas, and J. P. Ollivier, “Determination of chloride diffusion coefficient using two different steady-state methods：influence of concentration gradient,”Chloride Penetration into Concrete, Proceedings of the International RILEM Workshop, pp. 150-160, 1993.
19. C. C. Yang, S. W. Cho, and R. Huang, “The relationship between charge passed and the chloride ion concentration in concrete using steady state chloride migration test,”Cement and Concrete Research, Vol. 32, Issue 2, pp. 217-222, 2002.
20. ASTM C876-91, “Standard Test Method for Half-Cell Potentials of Uncoated Reinforcing Steel in Concrete,”Annual Book of ASTM Standards, Section 4, Vol. 4, 1999.
21. W. Morris, A. Vico, M. Vazquez, and S.R. de Sanchez, “Corrosion of reinforcing steel evaluated by means of concrete resistivity measurements,” Corrosion Science, Vol. 44, pp. 81-99, 2002.
22. 中華民國熱浸鍍鋅協會網，http://www.galtw.org.tw/。
23. 柏林防蝕塗料股份有限公司，http://www.berlin.com.tw/。
24. J. Hyks, T. Astrup, and T.H. Christensen, “long-term leaching from MSWI air-pollution-control residues : leaching characterization and modeling,”Journal of Hazardous Materials, Vol. 162, pp. 80-91, 2009.
25. 黃浩梁，「焚化底碴特性及其再利用管理系統之研究」，國立中央大學環境工程研究所碩士論文，2001。
26. 黃靖云，「不同養護條件對都市垃圾焚化底渣中重金屬溶出特性之影響」，嘉南藥理科技大學環境工程與科學系碩士論文，2008。
27. CEN/TS 14405, “Characterization of waste – Leaching behaviour tests – Up-flow percolation test (under specified conditions),”British Standards, 2004.
28. H.A. van der Sloot, A. van Zomeren, J.J. Dijkstra, D. Hoede, J. Jacobs, and H. Scharff, “Prediction of long-term leachate quality and chemical speciation for a predominantly inorganic waste landfill,”Ninth International waste management and landfill symposium, 2003.
29. K. A. Snyder, “The relationship between the formation factor and the diffusion coefficient of porous materials saturated with concentrated electrolytes: theoretical and experimental considerations,” Concrete Science and Engineering, Vol. 3, No. 12, pp. 216-224, 2001.
30. K. A. Snyder, “Validation and modification of the 4SIGHT computer program, ” National Institute of Standards and Technology Gaithersburg, MD 20899, NISTIR 6747, 2001.
31. 張蕙蘭，「國外焚化底渣再利用介紹」，經濟部永續產業發展雙月刊，第12期，pp. 54-64，2003。
32. C. C. Yang, L. C. Wang, and T. L. Weng, “Using charge passed and total chloride content to assess the effect of penetration silane sealer on the transport properties of concrete,” Materials Chemistry and Physics, Vol. 85, pp. 238-244, 2004.
33. Miguel A. Climent, Guillem de Vera, Jesús F. López, Estanislao Viqueira, and Carmen Andrade, “A test method for measuring chloride diffusion coefficients through nonsaturated concrete. PartⅠ. The instantaneous plane source diffusion case,” Cement and Concrete Research, Vol. 32, Issue 7, pp. 1113-1123, 2002.
34. N. Otsuki, S. Nagataki, and K. Nakashita, “Evaluation of AgNO3 solution spray method for measurement of chloride penetration into hardened cementitious matrix materials,” ACI Materials Journal, Vol. 89, No. 6, pp. 587–592, 1992.
35. National Institute of Standards and Technology, http://ciks.cbt.nist.gov/~bentz/menu0002.html.

指導教授

李釗(Chau Lee)

審核日期

2011-1-18

推文