| DC 欄位 |
值 |
語言 |
| DC.contributor | 化學工程與材料工程學系 | zh_TW |
| DC.creator | 王彥翔 | zh_TW |
| DC.creator | Yen-hsiang Wang | en_US |
| dc.date.accessioned | 2013-12-31T07:39:07Z | |
| dc.date.available | 2013-12-31T07:39:07Z | |
| dc.date.issued | 2013 | |
| dc.identifier.uri | http://ir.lib.ncu.edu.tw:88/thesis/view_etd.asp?URN=100324050 | |
| dc.contributor.department | 化學工程與材料工程學系 | zh_TW |
| DC.description | 國立中央大學 | zh_TW |
| DC.description | National Central University | en_US |
| dc.description.abstract | 本研究以單塔四步驟變溫吸附程序及單塔三步驟變壓程序，進行較小型發電廠煙道氣中CO2的捕獲模擬，其進料組成為15.03%之CO2與84.97%的N2，所使用的吸附劑為依台電綜合研究所配方製備的聚苯胺固態CO2吸附劑，此吸附劑只吸附CO2，N2則為不吸附氣體。其吸附劑之吸附量為利用微量天平取得CO2飽和吸附量，以Langmuir-Freundlich isotherm吸附模式來回歸實驗數據，並進行突破曲線驗證以得到線性驅動力質傳係數 。經過不同的操作變因探討以取得最佳的操作條件，以期將CO2濃度提升至90%以利之後封存，減少溫室氣體的排放。
模擬程式中使用了method of lines結合upwind differences和cubic spline approximation，再以ODEPACK套裝軟體中之LSODE程式對時間作積分，估計出下段時間的濃度、溫度及壓力，之後一直重複循環計算到系統達到週期性穩態為止。
經過變因探討後得到的最佳程序為單塔三步驟(含氮氣沖洗)變壓吸附程序，最佳操作條件為進料壓力4.0 atm、同向減壓壓力1.0 atm、逆向減壓壓力0.1 atm、塔長 550 cm、進料時間400 s、同向減壓時間30s及沖洗時間450 s，在此條件下其結果為CO2濃度91.77%，回收率為91.08%，捕捉每噸二氧化碳在絕熱壓縮或膨脹情況下所需能耗為1.04GJ/ton CO2。 | zh_TW |
| dc.description.abstract | In this simulation study, there are two adsorption process, one-bed four-step temperature swing adsorption (TSA) and one-bed three-step pressure swing adsorption (PSA) which are utilized to separate CO2 and N2 from small size power plant flue gas(15.03% CO2, 84.97% N2) with solid polyaniline sorbent. The adsorption capacity of sorbent was measured by the Micro-Balance Thermo D-200 to obtain adsorption equilibrium data of CO2, CO2 is the only adsorbate. Then Langmuir-Freundlich isotherm model is used to establish the equilibrium isotherms by regression. After the isotherm regression, the verification of breakthrough curves are implemented to determine mass transfer coefficient, . After the process operation variables discussion, the optimal conditions are obtained to concentrate CO2 above 90% purity for storage to reduce the emission of green-house-gases.
The method of lines is utilized, combined with upwind differences, cubic spline approximation and LSODE of ODEPACK software to solve the problem. The concentration, temperature, and adsorption quantity in the bed are integrated with respect to time by LSODE of ODEPACK software. The simulation is stopped when the system reaches a cyclic steady state.
After the variables discussion, the best process is one-bed three-step PSA process with nitrogen purge and the best operating condition is feed pressure 4.0 atm, co-current depressurization pressure 1.0 atm, vacuum pressure 0.1 atm, bed length 550 cm and step time at 400, 30 and 450 s. The results of the best operating condition are 91.77% purity and 91.08% recovery of CO2 with an energy consumption of 1.04 GJ/tonCO2 at adiabatic compression and expansion conditions. | en_US |
| DC.subject | 變溫吸附 | zh_TW |
| DC.subject | 變壓吸附 | zh_TW |
| DC.subject | 二氧化碳捕獲 | zh_TW |
| DC.subject | 煙道氣 | zh_TW |
| DC.subject | temperature swing adsorption | en_US |
| DC.subject | pressure swing adsorption | en_US |
| DC.subject | CO2 capture | en_US |
| DC.subject | flue gas | en_US |
| DC.title | 利用吸附程序於較小型發電廠煙道氣進氣量下捕獲二氧化碳之模擬 | zh_TW |
| dc.language.iso | zh-TW | zh-TW |
| DC.title | Simulation of Carbon Dioxide Capture from Small Power Plant Flue Gas by Adsorption | en_US |
| DC.type | 博碩士論文 | zh_TW |
| DC.type | thesis | en_US |
| DC.publisher | National Central University | en_US |