| DC 欄位 |
值 |
語言 |
| DC.contributor | 土木工程學系 | zh_TW |
| DC.creator | 艾芬娜 | zh_TW |
| DC.creator | Alfinna Mahya Ummati | en_US |
| dc.date.accessioned | 2018-7-12T07:39:07Z | |
| dc.date.available | 2018-7-12T07:39:07Z | |
| dc.date.issued | 2018 | |
| dc.identifier.uri | http://ir.lib.ncu.edu.tw:88/thesis/view_etd.asp?URN=105322606 | |
| dc.contributor.department | 土木工程學系 | zh_TW |
| DC.description | 國立中央大學 | zh_TW |
| DC.description | National Central University | en_US |
| dc.description.abstract | 大多數地震下的支承分析會假設有恢復力與摩擦力，但往往只能取得支承之最終位移和力量等數據，無法取得個元件之影響比重。本研究將使用FBM模擬支承，其中由三種元件組成，分別為於橋面板與支承上方間之摩擦元件、支承中間模擬橡膠之恢復力元件與支承下方與柱頂間之摩擦元件。
本研究使用近域地震波集集大地震TCU068, TCU102和TCU052進行分析，並符合規範之台中設計地震反應譜，再與遠域地震El-Centro大地震ELX354, ELX421和ELX600進行比較。在使用FBM支承系統於本橋梁進行分析時，將證實恢復力元件和摩擦元件可以獨立運算。本研究的目的為替換數種不同的摩擦係數以觀察橋梁動力反應之變化；其次，透過比較不同摩擦係數所造成之橋梁行為，找出最適合之摩擦係數使消能行為最佳；第三，確定最佳摩擦參數便於設計兩個甲板間隙，以避免地震發生時甲板發生碰撞；第四，確定最佳摩擦參數便於設計帽梁寬度，以避免地震發生時橋面版滑落。 | zh_TW |
| dc.description.abstract | Functional Bearing Model (FBM) is an idea to represent 1 link analysis that used in common with divide it into 3 links based on each function. In this research, the rubber bearing divided into 3 elements as representation of rubber bearing system, they are: Friction element in the top of sliding interface between bearing and deck, Rubber in the middle link as a restoring element, and Frictional element in the bottom of sliding interface between bearing and column.
A shaking table size bridge proposed under the normalized peak ground acceleration under the design spectra of the near fault ground motions of Chi-Chi earthquakes TCU068, TCU102, and TCU052. In this research of FBM analysis, proof that the contribution of the rubber element and friction elements can be calculated independently.
The purposes of this research are: First, to study about the effect of variation of the friction coefficient that applied on the top surface and bottom surface of the rubber bearing system. Second, to study about determining several configuration of the friction coefficient to design a proper rubber bearing system. Third, to study about determining several configuration of the friction coefficient to design a gap between two decks in order to avoid the decks crashing when the earthquakes happen. Fourth, to study about determining several configuration of the friction coefficient to design enlargement of the column’s cap beam in order to avoid the decks falling when the earthquakes happen. | en_US |
| DC.subject | 功能軸承模型 | zh_TW |
| DC.subject | 近斷層 | zh_TW |
| DC.subject | 反應譜 | zh_TW |
| DC.subject | 橋梁分析 | zh_TW |
| DC.subject | 動力分析 | zh_TW |
| DC.subject | Functional Bearing Model | en_US |
| DC.subject | Near Fault | en_US |
| DC.subject | Response Spectrum | en_US |
| DC.subject | Shaking Table Test Model | en_US |
| DC.subject | Bridge Analysis | en_US |
| DC.subject | Dynamic Analysis | en_US |
| DC.subject | Friction Coefficient | en_US |
| DC.subject | Rubber Bearing System | en_US |
| DC.title | Functional Bearing Model (FBM) Analysis Under the Design Spectra of Near Fault Ground Motions | zh_TW |
| dc.language.iso | zh-TW | zh-TW |
| DC.title | Functional Bearing Model (FBM) Analysis Under the Design Spectra of Near Fault Ground Motions | en_US |
| DC.type | 博碩士論文 | zh_TW |
| DC.type | thesis | en_US |
| DC.publisher | National Central University | en_US |