博碩士論文 90323033 完整後設資料紀錄

DC 欄位 語言
DC.contributor機械工程學系zh_TW
DC.creator葉明山zh_TW
DC.creatorMing-Shan Yehen_US
dc.date.accessioned2003-7-3T07:39:07Z
dc.date.available2003-7-3T07:39:07Z
dc.date.issued2003
dc.identifier.urihttp://ir.lib.ncu.edu.tw:88/thesis/view_etd.asp?URN=90323033
dc.contributor.department機械工程學系zh_TW
DC.description國立中央大學zh_TW
DC.descriptionNational Central Universityen_US
dc.description.abstractA201(Al-Cu-Mg-Ag合金)為一高強度鋁合金,隨著Ag含量的增加,強化機制由θ’相逐漸轉為Ω相,且當施行不同熱處理時,晶界析出形態也會跟著改變。 應力腐蝕破裂是A201鋁合金破裂的原因之一,其破壞性會隨著析出形態而改變,故本研究之目的在探討Ag含量與熱處理對A201鋁合金應力腐蝕性之影響。 實驗設計四種銀含量試片,分別為0wt.%Ag、0.3 wt.%Ag、0.6 wt.%Ag與0.9 wt.%Ag含量的Al-4.6Cu-0.3Mg合金,施以不同的時效熱處理(T4、T6、RRA、T7),探討在應力腐蝕環境下,各種時效熱處理條件對應力腐蝕敏感性的影響。並用光學顯微鏡(OM)、掃描式電子顯微鏡(SEM)、穿透式電子顯微鏡(TEM)、微差掃描熱分析儀(DSC)、導電度(%IACS)、硬度試驗、拉伸試驗(Tensile Test)與慢應變速率試驗(SSRT)等方法,探討微結構的變化與材料機械性質和抗應力腐蝕敏感性之關係。 由實驗結果可知,在人工時效熱處理後,合金成份含銀0.6 wt.%時即能有效促使Ω相大量析出,進而大幅提升材料的機械強度。且隨著銀含量的增加,雖然能使Ω析出相增加且分布較為細密,卻也造成晶界處陽極溶解效應越趨嚴重;而T7熱處理晶界析出物粗大,無析出帶較寬,也使得抗應力腐蝕效果較T6、RRA佳。zh_TW
dc.description.abstractA201(Al-Cu-Mg-Ag alloy)is a high strength aluminum alloy. With the increasing of Ag content,Ω phase will replace θ’ phase become the main strengthening phase. After different heat treatment, grain boundary precipitations will change. Stress corrosion cracking is one reason of A201 aluminum alloy happen to crack and the destructiveness will be different with the form of the precipitation. The effect of Ag content and heat treatment on stress corrosion cracking properties of A201 alloys were investigated. Using four different Ag content (0wt.%Ag、0.3wt.%Ag、0.6wt.%Ag and 0.9wt.%Ag) materials in the experiment. After different aging (T4、T6、RRA、T7), investigate the effect of heat treatment on the stress corrosion cracking of alloys, by using optical microscopy (OM), differential scanning calorimeter (DSC), electrical conductivity meter (%IACS), scanning electron microscopy (SEM), transmission electron microscopy (TEM). Analyzing the variation of microstructure of the alloys to compare with the variation of mechanical properties and stress corrosion cracking. Experimental results show that after artificial aging, alloy contains 0.6 wt.% Ag can promote Ω phase precipitate large, and improves the mechanical strength. With the increasing of Ag content, Ω phases precipitate more and finely, but anodic dissolution is serious at the grain boundaries. After T7 tempering, the grain boundary precipitations become coarse and the precipitate free zone becomes wide, then the stress corrosion cracking resistance is better than T6 and RRA tempering.en_US
DC.subject熱處理zh_TW
DC.subjectΩ相zh_TW
DC.subject應力腐蝕性zh_TW
DC.subjectAg含量zh_TW
DC.subjectA201合金zh_TW
DC.subjectA201 alloyen_US
DC.subjectAg contenten_US
DC.subjectheat treatmenten_US
DC.subjectstress corrosion crackingen_US
DC.subjectΩ phaseen_US
DC.titleAg含量與熱處理對A201合金應力腐蝕性之影響zh_TW
dc.language.isozh-TWzh-TW
DC.titleEffect of Ag content and Heat Treatments on Stress Corrosion Cracking of A201 Alloysen_US
DC.type博碩士論文zh_TW
DC.typethesisen_US
DC.publisherNational Central Universityen_US

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明