![]() |
|
以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數:21 、訪客IP:18.119.255.161
姓名 陳建宏(Chen chien hung) 查詢紙本館藏 畢業系所 光電科學與工程學系 論文名稱 以田口法優化LED車燈散熱系統之研究
(The study for optimization of LED headlight cooling system by using Taguchi Methods)相關論文 檔案 [Endnote RIS 格式]
[Bibtex 格式]
[相關文章]
[文章引用]
[完整記錄]
[館藏目錄]
[檢視]
[下載]
- 本電子論文使用權限為同意立即開放。
- 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
- 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
摘要(中) 本研究是利用熱管的高導熱特性,應用在機車車燈散熱系統上,並採用田口式直交表實驗計畫法優化,參數設計採用八個合適的設計參數,分別是熱管壓扁厚度、鰭片的數目、鰭片之間距、鰭片之厚度、鰭片之高度、散熱片長度、鰭片上之輻射材質(放射率)、MCPCB尺寸等控制因子,每個因子分別有三個水準做參數設計,調整參數以降低LED車燈中LED之溫度。
選用田口式直交表實驗法的L18(21×37)直交表來設定各組參數值,再利用計算流體力學(Computational Fluid Dynamics, CFD)模擬,求得最後溫度。
初始設計得到T_c溫度為86.17°C,以田口方法之望小特性品質特性分析計算後,得到最佳預測設計因子,以此最佳設計因子以計算流體力學來模擬可得到模擬T_c溫度為76.11°C,LED的溫度明顯有下降,証明此方式可以有效率的改善設計開發流程之時間。
使用其他流體可以進一步降低LED溫度,本研究使用純水取代空氣來當流體與散熱片進行熱交換,求得最佳所需的水量為15公升,此時T_c可以降低至63°C,大大提高了散熱系統的效率。
摘要(英) This research using heatpipe in thermal cooling system of motorcycle’s headlight, and executing Taguchi method to analysis. We establish the eight parameters such as the thickness of heat pipe, and number of fins, the pitch of fins, the fin thickness, the height of fin, the heat sink length, the radiation material on heat sink, and the size of MCPCB. After the above eight parameter must be determined. Next, these parameters are divided into three levels separately in order to reduce the Tc that on the MCPCB temperature of LED headlight.
By using Taguchi Method makes the optimization of LED headlight cooling system easier whereas the simulation times of the 8 parameters and the 3 levels of each parameter will be in total 4374 times. We establish a product that can effectively reduce simulation times to 18. The Tc temperature of LED headlight is lower than all of probable combination exactly. And using CFD(Computational Fluid Dynamics) to simulate the system finally get the Tc temperature.
The original design of cooling system without optimization by Taguchi Method, the Tc temperature of cooling system was 86.17°C. With the optimal optimization design we can reach the Tc is 76.11°C, the temperature of sink and MCPCB was significantly decreased. Moreover the optimization by Taguchi Method design can get the best construction in as short time. Therefore, this research for the cooling components decreases development time and the cost of production.
Because use other fluid in this system could decease the temperature of system, so this research take pure water as the cooling fluid contact with the heat sink. Then can get the optimal water volume in this cooling system. It is useful to down the Tc temperature to 63°C.
關鍵字(中) ★ 田口式直交表實驗法
★ 直交表
★ 熱管
★ LED車燈關鍵字(英) ★ Taguchi Method
★ Orthogonal arrays
★ Heat pipe
★ LED headlight論文目次 目 錄
摘 要......................................................i
ABSTRACT......................................................ii
目 錄....................................................iii
圖 目 錄......................................................vi
表 目 錄......................................................ix
第一章 緒論...................................................1
1-1 研究動機與文獻回顧......................................1
1-2 論文貢獻................................................5
1-3 論文架構................................................6
第二章 基礎理論...............................................7
2-1 熱傳導理論..............................................7
2-1-1 熱傳導..............................................8
2-1-2 熱對流.............................................10
2-1-3 熱輻射.............................................14
2-2 熱管理論與介紹.........................................15
2-2-1 熱管工作原理.......................................16
2-2-2 熱管之特性限制.....................................17
2-3 實驗設計法簡介.........................................19
2-3-1 田口式直交表實驗法之簡介...........................21
2-3-2 參數設計...........................................24
2-3-3 直交表.............................................28
2-3-4 信號雜音(S/N)比....................................30
2-4 計算流體力學分析之基礎理論.............................31
第三章 研究方法..............................................35
3-1 LED頭燈結構及散熱設計.................................35
3-1-1 LED散熱系統初始設計之模擬條件......................39
3-2 實驗方法及步驟.........................................41
3-3 選擇直交表並配置控制因子及水準數.......................42
3-3-1 LED頭燈散熱系統之設計限制.........................42
3-3-2 輻射材料選用.......................................43
3-4 SOLIDWORKS Flow Simulation軟體分析流程................44
第四章 實驗結果與討論........................................46
4-1 以田口方法建立模擬模型.................................46
4-2 使用田口方法建立模擬模型之模擬結果.....................47
4-3 LED溫度分析並計算控制因子之 S/N比.....................56
4-4 計算所有控制因子與品質特性之關係.......................58
4-5 模擬結果與分析.........................................60
4-6 隨機挑選控制因子模擬比對...............................62
4-7 實際樣品測試與改變冷卻流體.............................63
4-8 實驗討論...............................................65
第五章 結論與未來展望........................................67
5-1 結論...................................................67
5-2 未來展望...............................................68
參考文獻......................................................69
參考文獻 [1] Jeff Y. Tsao, “Solid-state Lighting Lamps, Chips,and Materials for Tomorrow”,IEEE Circuit & Devices Magazine, Vol. 20, issue pp.28~37,(2004).
[2] N. Holonyak and S. F. Bevacqua, “coherent(visible) light emission from Ga(As 1-x P x) junctions”, Appl. Phys. lett.1, 82-83(1962).
[3] C. P. Kuo, R. M. Fletcher, T.D. Osentowski, M. C. Lardizabal, M. G. Caraford, and V. M. Robbins, “High performance AlInGaP visible light emitting diodes”, Appl.Phys. Lett.57, 2937-2939(1990).
[4] H. Sugawara, M. Ishikawa, and G. Harakoshi, “High-Efficiency InAlGaP/GaAs visible light-emitting diodes”,Appl. Phys. Lett. 58,1010-1012(1991).
[5] S. Nakamura, T.Mukai, and M. Senoh, “High-grightnness InGaN/AlGan double-heterostructure blus-green-light-emitter diodes”,J. Appl.Phys. 76,8189-8191(1994).
[6] S. Nakamura, M. Senoh, N. Iwasa, S. Nagahama, T. Yamada, and T. Mukai, “Superbright Green InGaN Single-Quantum-Well-Structure Light-Emitting Diodes”,Jpn. J.Appl.Phys. 34, L1332-L1335 (1995).
[7] Jeong Park and Chin C. Lee,“An Electrical Model With Junction Termperature for Light-Emitting Diodes and the Impact on Conversion Efficiency”,IEEE Electron Device Letters, vol. 26,no. 5,pp. 308~310, (2005).
[8] Eugene Hong and Nadarajah Narendran, “A Method for Projecting Useful Life of LED Lighting Syatems”,Third International confernnce on Solid State Lighting, Proceedings of SPIE, vol.5178, pp. 93~99,(2004).
[9] Y. Shimizu, K. Sakano, Y. Noguchi, and T. Moriguchi, “Light emitting device having a nitride compound semiconductor and a phosphor containing a garnet fluorescent material”, United State Paten, US 5998925(1999).
[10] Nadarajah Narendran and Yumin Gu,“Life of LED-BASE White Light Source”,IEEE/OSA Journal of Display Technology, vol. 1, no.1,pp. 167~171,(2005).
[11] 依日光,熱管技術理論實務,復興出版社,(2000)。
[12] 李冠賢,“垂直放置鰭片之自然對流熱傳性能實驗研究”,國立中央大學機械工程學系碩士論文,(2010)。
[13] 李輝煌,「田口方法品質設計的原理與實務」,高立圖書,民國89年8月。
[14] 蘇朝墩,「產品穩健設計」,中華民國品質學會發行,民國86年8月。
[15] S.H. Park, Robust Design and Analysis for Quality Engineering, Chapman & Hall, pp. 25-58,(1996).
[16] Incropera Dewitt 原著,侯順雄、王松浩、張仲卿譯者,「熱傳遞」,高立圖書,民國 96年10月。
[17] F.P. Incropera, D.P. DeWitt, T. L. Bergmann and A. S. Lavine, Fundamentals of Heat and Mass Transfer, 6th ed., Wiley
[18] http://en.wikipedia.org/wiki/Heat_pipe
[19] Y. Xuan, Y. Hong, Q. Li, “Investigation on Transient Behaviors of Flate plate Heat Pipes”, Experimental Thermal and Fluid Science,(2004),Vol.28, pp.249-255.
[20] 白東鑫,(2002) 年 5 月,金屬工業 36 卷 3 期, P.29。
[21] 簡國祥,(2000) 年 7 月,工業材料 163 期, P.188。
[22] 邱創標,(1992) 年 3 月,臺電工程月刊 523 期, P.54。
[23] Amir Faghri, ”Heat pipe science and technology”, 1976, pp.221-222.
[24] 楊清富、林聖泉,(2014)。應用 SolidWorks Flow Simulation 進行溫室內循環風扇流場分析之研究,臺南區農業改良場研究彙報 63:pp.83-98。
[25] Ostrach, S.,“An Analysis of Laminar Free Convection Flow and Heat Transfer about a Flat Plate Parallel to the Direction of the Generating Body Force”, National Advisory Committee for Aeronautics, Report 1111,(1953).
[26] Han-Youl Ryu, Kyoung-Ho Ha, Jung-Hye Chae, Ok-Hyun Nam, and Yong-Jo Park: Appl. Phys. Lett. 87,(2005) 093506-1.
[27] Lee Ya-Ju, Lee Chia-Jung, Chen Chih-hao,” Estimating the Junction Temperature of InGaN and AlGaInP Light-Emitting Diodes “,Japanese Journal of Applied Physics leet.50,(2011) 04DG18.
指導教授 張榮森 審核日期 2015-4-15 推文 plurk
funp
live
udn
HD
myshare
netvibes
friend
youpush
delicious
baidu
網路書籤 Google bookmarks
del.icio.us
hemidemi
myshare