顆粒床整合系統最適化設計與連續過濾驗證之研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：10

、訪客IP：3.22.51.241

姓名

許展瑞(Jan-Ray Hsu) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

顆粒床整合系統最適化設計與連續過濾驗證之研究

相關論文

★ 筆記型電腦改良型自然對流散熱設計	★ 移動式顆粒床過濾器濾餅流場與過濾性能之研究
★ IP67防水平板電腦設計研究	★ 汽車多媒體導航裝置散熱最佳化研究
★ 流動式顆粒床過濾器三維流場觀察及能性能測試	★ 流動式顆粒床過濾器冷性能測試
★ 流動式顆粒床過濾器過濾機制研究	★ 二維流動式顆粒床過濾器內部配置設計研究
★ 循環式顆粒床過濾器過濾性能研究	★ 流動式顆粒床過濾器之流場型態設計與研究
★ 流動式顆粒床過濾器之流動校正單元設計與分析研究	★ 流動式顆粒床過濾器之雙葉片型流動校正單元設計與冷性能過濾機制研究
★ 稻稈固態衍生燃料成型性分析之研究	★ 流動式顆粒床過濾器之不對稱葉片設計與冷性能過濾機制研究
★ 流動式顆粒床過濾器之滾筒式粉塵分離系統與冷性能過濾及破碎效應研究	★ 稻稈固態衍生燃料加入添加物成型性分析之研究

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

本研究以長時間連續化過濾為目標，進行整合系統最適化改善設計與連續過濾驗證，以達到長時間連續除塵過濾，而所得結果將可提供未來高溫熱模除塵系統建置之依據。在系統最適化改善設計方面，主要進行粉塵供應系統與濾材/粉塵滾筒篩分系統氣密性改善項目，其改善後粉塵供應系統之設計，將可穩定且精確的供應連續化過濾粉塵量；而在濾材/粉塵滾筒篩分系統氣密性上，針對滾筒進料口與顆粒床體下料閥銜接處、滾筒出料口與濾材循環再生系統進行氣密性改善設計，以達到整合系統氣密性與濾材循環再生目的。連續過濾驗證方面，針對濾材/粉塵滾筒篩分性能與長時間連續過濾進行一系列實驗測試與分析。在濾材/粉塵篩分性能上，而過濾後出口粉塵比例與篩分效率等參數，將影響篩分性能的好壞。由出口粉塵比例結果可知，在滾筒轉速42.5 rpm與滾筒角度5°時，有著最佳篩分效率。在長時間連續化過濾驗證方面，針對所建立與改善設計後的整合循環顆粒床過濾系統，實際探討床體壓降、過濾效率與出口粉塵粒徑變化間的影響，由實驗結果可知在濾材質量流率240 g/min及過濾自由表面風速50 cm/s的條件下，可以得到較佳的過濾效率與較小的出口粉塵粒徑排放，而在長時間24小時連續過濾下，過濾效率與出口粉塵粒徑( )分別可達98.9% 與7 μm，由此結果將可達到長時間連續化過濾運轉之目標，並提供未來建立中高溫除塵技術開發與商業化依據。

摘要(英)

The goals of this study is for longtime continuity filtering by optimizing design of granular bed and sub system, and executing systematic continuity operation test to reach longtime continuity filtering functioning. There are the improvements of dust supply and the airtightness of trommel screen system for optimizing designing. After improving dust supply steadily and accurately with suitable vibrating time ratio for the continuity filtration. On the airtightness of trommel screen system, we have improved connections between granular bed, screen system and regeneration system. For the systematic continuity operation test, there are series of experiments of screen performance and integration system continuity filtration test. For the continuity filtration procedure, the ratio of ash would influence on screen performance. With the results, ratio of dust, we can have the best results in rotational speed 42.5 rpm and tilt angle 5°. There would be the highest filtration efficiency and the lowest discharged particle size by 240 g/min of media mass flow rate and 50 cm/s of surface velocity for the continuity filtration test with the system after optimization, filtration efficiency and the discharged particle size( ) could reach 98.9% and 7μm respectively. The filtration performance reached the target of a continuous integration system and longtime filtration operation from the above research results, which could be provided information of commercialization system in the future.

關鍵字(中)

★ 移動式顆粒床過濾
★ 篩分性能
★ 連續過濾
★ 中高溫除塵

關鍵字(英)

★ moving granular bed filtration
★ screen performance
★ continuity filtration
★ high-temperature filtration

論文目次

摘要 I
ABSTRACT VII
目錄 VIII
附圖目錄 XI
附表目錄 XVI
第一章簡介 1
1.1前言 1
1.2文獻回顧 10
1.3研究動機與目的 16
1.4論文架構 18
第二章連續化過濾整合系統最適化改善設計 20
2.1連續化過濾整合系統實驗設備 20
2.2粉塵供應系統最適化改善設計 28
2.2.1實驗設備 28
2.2.2實驗參數 32
2.2.3實驗步驟 34
2.3整合系統氣密性最適化改善設計 35
第三章整合系統連續化過濾驗證 39
3.1滾筒篩分性能測試－顆粒床進出口端粉塵比例 40
3.1.1實驗設備 40
3.1.2實驗參數 42
3.1.3實驗步驟 45
3.2滾筒篩分性能測試－濾材/粉塵滾筒篩分效率 48
3.2.1實驗設備 48
3.2.2實驗參數 49
3.2.3實驗步驟 52
3.3整合系統連續化過濾驗證運轉測試 54
3.3.1實驗設備 54
3.3.2過濾行為與分離機制 56
3.3.2.1分離過濾行為 57
3.1.3.2分離過濾機制 59
3.3.3操作參數 63
3.3.4實驗步驟 65
第四章結果與討論 68
4.1整合系統最適化改善設計 68
4.1.1粉塵供應器改善設計 69
4.1.2整合系統氣密性最適化設計 75
4.2顆粒床整合系統連續化過濾驗證實驗 77
4.2.1滾筒篩分性能測試－顆粒床進出口端粉塵比例分佈 78
4.2.2滾筒篩分性能測試－濾材/粉塵篩分效率 84
4.2.3整合系統之長時間連續化過濾驗證 94
第五章結論 104
第六章未來工作與建議 107
參考文獻 109

參考文獻

1. BP Statistical Review of World Energy, 2014, http://www.bp.com/
2. World Energy Outlook, 2014, http://www.iea.org/,
3. 經濟部能源局能源報導，2012，http://web3.moeaboe.gov.tw/
4. Seville (Ed.), j. p. k., 1997, Gas Cleaning in Demanding Applications, Blackie Academic & Professional, London, pp. 96-127.
5. Flagan, R.C., Seinfeld, J.H., 1998, Fundamentals of air pollution engineering, Prentice-Hall, Inc.
6. 魏維新，「環境汙染學」，1997，合記圖書出版社，1997，pp. 181~236
7. 張益國等，2009，「環境保護概念」，中臺科技大學
8. Ahmadi, G. and Smith, D.H., 2002, Gas Flow and Particle Deposition in the Hot-Gas Filter Vessel of the Pinon Pine Project, Powder Technology, Vol. 128, pp. 1-10.
9. Fraser, S., Osborne, S., 2007, Potential Exports of U.S. Clean Coal Technology through 2030, International Trade Administration.
10. Kiga, T., 2008, Introduction of Clean Coal Technology in Japan, in Gas Cleaning at High Temperatures, IEEJ Transactions on Electrical and Electronic Engineering, Vol. 3, pp. 43-47.
11. Minchener, A. J., McMullan, J. T., Kubica, K. 2008, Clean coal technology promotion and dissemination, European Commission, Directorate-General for Research and Innovation.
12. 古政芳，2000，「流動式顆粒床過濾器阻礙物配置之設計」，國立中央大學機械工程研究所。
13. 許嘉仁，2011，「The Study of Gas Flow Behaviors and Filtration Performance of Moving Granular Bed Filter」，國立中央大學機械工程研究所。
14. Hsiau, S.S., Smid, J., Tsai, F.H., Kuo, J.T. and Chou, C.S, 2004, Placement of Flow-Corrective Elements in a Moving Granular Bed with Louver-Walls, Chemical Engineering and Processing, Vol. 43, pp.1037-1045.
15. 李宣億，2008，「流動式顆粒床過濾器之滾筒式粉塵分離系筒與冷性能過濾及破碎效應研究」，國立中央大學機械工程研究所。
16. 張益綸，2013，「顆粒床過濾連續化整合系統開發研究」，國立中央大學機械工程研究所
17. 紀克彥，2005，「顆粒床過濾器濾材粉塵振動篩分之研究」，國立中央大學機械工程研究所
18. Kuo, J.T., Smid, J., Hsiau, S.S., Wang, C.Y. and Chou, C.S., 1998, Stagnant Zones in Granular Moving Bed Filter for Flue Gas Cleanup, Filtration and Separation, Vol. 35, pp. 529-534.
19. Hsiau, S.S., Smid, J., Wang, C.Y., Kuo, J.T. and Chou, C.S., 1999, Velocity Profiles of Granules in Moving Bed Filters, Chemical Engineering Science, Vol. 54, pp. 293-301.
20. Hsiau, S.S., Smid, J., Tsai, F.H., Kuo, J.T. and Chou, C.S., 2001, Velocities in Moving Bed Filters, Powder Technology, Vol. 114, pp. 205-212.
21. Newton, R.H., Dunham, G.S., and Simpson, T. P., 1945, The TCC Catalytic Cracking Process for Motor Gasoline Production, Trans actions of the American Institute of Chemical, Engineers, Vol. 41, pp. 215-218.
22. Morse, H. H., May 29, 1951, Method of Effecting Contact in a Pebble Heater, Patent, U. S. 2,255,052.
23. Johanson, J.R., 1966, The Use of Flow Corrective Inserts in Bins, Engineering for Industry-Transactions of the ASME, Vol. 88, pp. 224-230.
24. Johanson, J.R., and Kleysteuber, W.K., 1966, Flow Corrective Inserts in Bins, Chemical Engineering Progress, Vol. 62, pp. 79-83.
25. Johanson, J.R., 1967/68, The Placement of Insert to Correct Flow Problems, Powder Technology, Vol. 1, pp. 328-333.
26. 林政煌，2004，「流動式顆粒床過濾器之流場型態設計與研究」，國立中央大學機械工程研究所。
27. 高偉智，2005，「流動式顆粒床過濾器之流動校正單元設計與分析究」，國立中央大學機械工程研究所。
28. 陳一順，2001，「流動式顆粒床過濾器三維流場觀察與冷性能測試」，國立中央大學機械工程研究所。
29. 馬家駒，2002，「流動式顆粒床過濾器冷性能測試」，國立中央大學機械工程研究所。
30. 賴信璋，2003，「流動式顆粒床過濾器過濾機制研究」，國立中央大學機械工程研究所。
31. 蔡信安，2006，「流動式顆粒床過濾器之雙葉片型流動校正單元設計與冷性能過濾機制研究」，國立中央大學機械工程研究所。
32. 王超，2005，「垃圾中轉站滾筒篩的設計及動態仿真研究」，北京機械工業學院。
33. Green, D.W. and Maloney, J.W., Perry’s, 1984, Chemical Engineering’s Handbook, 6th Ed., International Student Edition (Eds.), McGraw-Hill ,pp. 20-105.
34. Gutfinger, C. and Tardos, G. I., 1979 Theoretical and experimental investigation on granular bed dust filters. Atmospheric Environment, Vol. 6, pp. 853-867.
35. Haghshenasfard, M., Zivdar, M., Rahimi, R. and Esfahany, M. Nasr, 2007, CFD simulation of gas distribution performance of gas inlet systems in packed columns, Chemical Engineering. & Technol., Vol. 30, pp. 1176-1180.
36. Bai, J.H., Wu, S.Y., Lee, A.S. and Chu, C.Y., 2007 , Filtration of Dust in a Circulating Granular Bed Flter with Conical Louver Plates (CGBF-CLPs), Hazardous Materials, Vol. 142, pp. 324-331.
37. Kirsh, A. A. and Stechkina, I. B., 1978, The Theory of Aerosol Filtration with Fibrous Filter, in Fundamentals of Aerosol Science, D. T. Shaw（ED.）, Wiley, New York.
38. Kalman, H., 1999, Attrition Control by Pneumatic Conveying, Powder Technology, Vol. 104, pp. 214-220.
39. Hoffmann, A.C., Stein, L.E., 2008, Gas Cyclones and Swirl Tubes：Principles, Design and Operation, Second Edition, pp.111-133.
40. Encyclopedia of Chemical Engineering Equipment, 2010, http://encyclopedia.che.engin.umich.edu/
41. Barth., W., 1956, Design and layout of the cyclone separator on the basis of new investigations., Brennstow-Wärme-Kraft (BWK)
42. Ma, A.C., Williams, K.C., Zhou, J.M., Jones, M.G., 2010, Numerical study on pressure prediction and its main influence factors in pneumatic conveyors, Chemical Engineering Science, Vol.65, pp.6247-6285
43. Moving difficult-to-handle bulk materials with flexible screw conveyors, 2011, http://www.processonline.com.au/
44. Toomey R.D. and Johnstone H.F., 1952, Gaseous Fluidization of Solid Particles, Chemical Engineering Progress, Vol. 48, pp. 220-225.
45. Gidaspow, D., Bahary, M. and Jayaswal, U.K., 1994, Hydrodynamic Models for Gas-Liquid-Solid Fluidization, American Society of Mechanical Engineers, FED., Vol. 185, pp.117-124.
46. Lee, K.W., 1981, Maximum Penetration Ofaerosol Particles in Granular Bed Filters, Journal of Aerosol Science, Vol. 12, pp. 79 -87.
47. Lee, K.W., and Gieseke, J.A., 1979, Collection of Aerosol Particles by Packed Bed, Environmental Science and Technology., Vol. 13, pp. 466-470.
48. Lee, K.W., and Gieseke, J.A., 1980, Note on the approximation of interceptional collection efficiencies, Journal of Aerosol Science, Vol. 11, pp. 335-341.
49. Coury, J.R., Thambimuthu, K.V. and Clift, R., 1987, Capture and Rebound of Dust in Granular Bed Filters., Powder Technology, Vol. 50, pp. 253-265.
50. Huang, C.H., and Tsai, C.J., 2002, The Particle Collection Efficiency Curves by the Porous Substrate of an Inertial Impactor, Aerosol and Air Quality Research, Vol. 2, pp.01-08.
51. Brown, R.C., Shi, Huawei, et al., 2003, Similitude Study of a Moving Bed Granular Filter, Powder Technology, Vol. 138, pp. 201-210.
52. Chen, Y. S., Hsiau, S. S., Lee, H. Y., Chyou, Y. P. and Hsu, C. J., 2010, Size Separation of Particulates in a Trommel Screen System, Chemical Engineering and Processing: Process Intensification, Vol. 49, pp. 1214-1221.
53. Arena, U., D′Amore, M. and Massimilla, M., 1983, Carbon attrition during the fluidized combustion of a coal, American Institute of Chemical Engineers, Vol. 29, pp. 40-49.
54. Morse, H. H., May 29, 1951, Method of Effecting Contact in a Pebble Heater, Patent, U. S. 2,255,052.
55. El-Hedok, I.A., Whitmer, L., Brown, R.C., 2011, The influence of granular flow rate on the performance of a moving bed granular filter, Powder Technology, Vol. 214, pp.69-76.

指導教授

蕭述三(Shu-San Hsiau)

審核日期

2015-1-29

推文