參考文獻 |
[1] “台達電於中央大學簡報資料,” 2013,12/19.
[2] 村山拓也、柴田洋, “熱交換器”. 中國 專利: ZL200480043616.1, 2009.
[3] “AB SEGERFRÖJD Compounds,” 2014. [線上]. Available: http://www.segerfrojd.com/.
[4] “廈門中惠空調,” 2014. [線上]. Available: http://www.xmzhh.com/.
[5] Burns, J., Jachuck, R., "Condensation studies using crosscorrugated polymer film compact heat exchangers," Applied Thermal Engineering, 21, pp. 495-510, 2001.
[6] Cheng, L., Van Der Geld, C., "Experimental study of heat transfer and pressure drop characteristics of air/water and air-steam/water heat exchange in a polymer compact heat exchanger," Heat Transfer Engineering, 26, pp. 18-27, 2005.
[7] Harris, C., Kelly, K., Wang, T., McCandless, A., Motakef, S., "Fabrication, modeling and testing of micro-cross flow heat exchangers," Journal of Microelectromechanical Systems, 11, pp. 726-735, 2002.
[8] Rousse, D., Martin, D., Theriault, R., Leveillee, F., Boily, R., "Heat recovery in greenhouses: a practical solution," Applied Thermal Engineering, 20, pp. 687-705, 2000.
[9] Saman, W., Alizadeh, S., "Modeling and performance analysis of a cross-flow type plate heat exchanger for dehumidification/cooling," Solar Energy, 70 (4), pp. 361-372, 2001.
[10] Jia, J., Peng, X., Sun, J., Chen, T., “An experimental study on vapor condensation of wet flue gas in a plastic heat exchanger,” Heat Transfer - Asian Research, 30, pp. 571-580, 2001.
[11] Yang, C.-Y. and Liu, W.-C., "Development of a mini liquid cooling system for high heat flux electronic device," Heat Transfer Engineering, 32 (7-8), pp. 690 - 696, 2011.
[12] “高力公司,” [線上]. Available: http://www.kaori-taiwan.com/brazed-plate.html.
[13] R. L. Webb, Principles of Enhanced Heat Transfer, Wylie Inter-Science, 1994.
[14] Kakac, S., Liu, H. and Pramuanjaroenkij, HEAT EXCHANGERS Selction, Rating and Thermal Design, CRC Press, 2012.
[15] T’Joen C., Park, Y., Wang, Q., Sommers, A., "A review on polymer film compact heat exchangers," International journal of refrigeration, 32, pp. 763-779, 2009.
[16] Bond, M. P., "Plate Heat Exchangers for Effective Heat Transfer," The Chemical Engineer, pp. 162-167, 1981.
[17] Focke, W. W., Zachariades, J., and Oliver, I., "The Effect of Corrugation Inclination Angle on the Thermohydraulic Performance of Plate Heat Exchangers," International Journal of Heat and Mass transfer, 28, pp. 1469-1479, 1985.
[18] Focke, W. W., "Selecting Optimum Plate Heat Exchanger Surface Patterns," Journal of Heat Transfer, 108, pp. 153-160, 1986.
[19] Chisholm, D. and Wanniarachchi, A. S., “Layout of Plate Heat Exchanger,” ASME/JSME Thermal Engineering Proceeding, 4, pp. 433-438, 1991.
[20] Heavner R. L., Kumar H., and Wanniarachchi A. S., "Performance of an Industrial Plate heat exchanger: Effect of Chevron Angle," AIChE Symposium Series, Heat Transfer-Atlanta, 89, pp. 262-267, 1993.
[21] Muley, A., Manglik, R. M., and Metwally, H. M., "Enhanced Heat Transfer Characteristics of Viscous Liquid Flows in A Chevron Plate Heat Exchanger," ASME Journal of Heat Transfer, 121, pp. 1011-1017, 1999.
[22] Abdel-Kariem, A. H., Fletcher, L. S., "A Comparative Analysis of Heat Transfer and Pressure Drop in Plate Heat Exchangers," 5th ASME/JSME Joint Thermal Engineering Conference Proceeding , Paper No. AJET99-6291, 1999.
[23] Muley, A., Manglik, R. M., "Experimental Study of Turbulent Flow Heat Transfer and Pressure Drop in a Plate Heat Exchanger with Chevron Plates," ASME Journal of Heat Transfer, 121, pp. 110-117, 1999.
[24] 林岳宏, 水對空氣在板式熱交換器之性能測試分析, 國立中央大學機械工程研究所碩士論文, 2004.
[25] Sieder, E.N., Tate, G.E., "Heat transfer and pressure drop of liquids in tubes," Industrial and Engineering Chemistry, vol. 28, p. 1429–1435, 1936.
[26] Focke, W.W. and Knibbe, P.G., "Flow visualization in parallel-plate ducts with corrugate walls," Journal of Fluid Mechanics, 165, pp. 73-77, 1986.
[27] 王啟川, 熱交換器設計, 五南圖書股份有限公司, 2007.
[28] Briggs, D.E., Young, E.H., "Modified Wilson plot techniques for obtaining heat transfer correlations for shell and tube heat exchangers," Chemical engineering progress symposium series, Vols. 92, No. 65, p. 35–45., 1969.
[29] Martin, H., "A theoretical approach to predict the performance of chevron-type plate heat exchangers," Chemical Engineering and Processing, 35, pp. 301-310, 1996.
[30] Wilson, E.E., "A basis for rational design of heat transfer apparatus," Transactions of the ASME, vol. 37, p. 47–82, 1915. |