 |
|
|
|
以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數：89 、訪客IP：18.226.94.206
姓名 張立群(Li-Chun Chang) 查詢紙本館藏 畢業系所 機械工程學系 論文名稱 移動式顆粒床過濾器應用於中高溫除塵及除焦油 相關論文 檔案 [Endnote RIS 格式]
[相關文章]
[文章引用]
[完整記錄]
[館藏目錄]
至系統瀏覽論文 ( 永不開放)
摘要(中) 在台灣目前以火力發電為主，藉由燃煤將熱能轉變為電能，而在燃煤過程中產生大量的污染物，不僅造成後端渦輪機損壞，更會污染環境，為防治污染方面重要議題。依先前開發之除塵技術-移動式顆粒床過濾系統，經常溫下連續過濾測試，過濾效果可達98%，然而工業應用均處高溫環境下，故本研究將依據此系統進行耐高溫建置，以探討中高溫除塵效率並透過此系統進行除焦油技術開發。
藉由加熱、氣送、粉塵供應及濾材輸送系統，控制入口氣體與濾材之溫度，使系統達到高溫狀態，模擬燃燒機組後端之情形。顆粒床以濾材連續流動的方式捕集粉塵，再由後端監控系統(Process Particle Counter，PPC)監測出口端粉塵，並比較入出口粉塵濃度
進行除塵效率分析。藉由改變溫度及濾材流動速率，探討中高溫顆粒床過濾效率之影響，並由其實驗之結果進行除焦油技術開發。
實驗結果顯示，過濾效率隨溫度上升而下降，其中質量流率於 360 g/min、粉塵濃度 7500ppmw，表面風速 50cm/s，常溫下，過濾效率可達 98%以上，而 600 ℃時，過濾效率降至89%，其主要原因乃高溫下氣體黏滯力上升，使捕集機制中的慣性衝擊下降，造成過濾效率下降。
而在除焦油方面，透過改變濾材流動速度，使前端含有焦油之中高溫氣體平均溫度231.2 ℃隨濾材的流動而降溫至平均溫度 45 ℃，藉由焦油之露點溫度特性，致使焦油凝結於濾材上，以達捕集之效果，並採樣床體出口端之焦油濃度與入口端進行比較，其過濾效率可達81%。摘要(英) Abstract
At present, Taiwan mainly base on thermal electric generation. By burning coal into
thermal energy, a large amount of pollutants are generated in the process of burning coal, which
not only causes damage to the rear-end turbines but also pollutes the environment, it is an
important issue in the prevention and control of pollution. According to the previously
developed dust removal technology –moving granular bed filter, continuous filtration test at
room temperature, found that the filtration efficiency reach to 98%.
However, industrial applications are under high temperature environment. Therefore, this
study will develop medium and high granular bed filter based on this system to explore high
temperature filtration efficiency. In the meantime, develop tar removal technology through this
system.
By heating, gas generation, dust supply and filter material delivery systems, the
temperature of the inlet gas and the filter material is controlled to bring the system to a high
temperature state. The granular bed captures the dust in a continuous flow of the filter material,
analyzing the filtration efficiency by monitoring the concentration of outlet by process particle
counter (PPC), and then compare the dust concentration inlet and outlet. The influence of the
filtration efficiency between the temperature and flow rate was discussed, and the tar removal
technology was developed through the results of the experiment.
The experimental results showed that the filtration efficiency decreases with the increase
of temperature. On the condition of mass flow rate of 360 g/min, dust concentration 7500 ppmw
and the filtration superficial velocity of 50 cm/s, the filtration efficiency up to 98% at room
temperature, while reaching to 89% at 600 ℃. The main reason is that the viscosity of the gas
decreases at high temperatures, which causes the inertial impact in the trapping mechanism to
decrease, resulting in a decrease in filtration efficiency.
In terms of tar removal, the high temperature gas containing tar in the inlet is cooled with
III
the flow of the filter material by changing the flow rate, which makes tar condense on the filter
material because of tar dew point. Comparing the inlet and outlet concentration, found the
filtration efficiency reach to 81%.關鍵字(中) ★ 顆粒床過濾系統
★ 中高溫除塵
★ 除焦油技術
★ 淨煤技術關鍵字(英) ★ Granular bed filter
★ Hot gas clean
★ Tar removal
★ Clean coal論文目次 目錄
摘要 ............................................................................................................................................ I
Abstract .................................................................................................................................... II
致謝 ......................................................................................................................................... IV
目錄 ........................................................................................................................................... V
圖目錄 .................................................................................................................................... VII
表目錄 ..................................................................................................................................... IX
符號說明 ................................................................................................................................... X
第一章 緒論 .............................................................................................................................. 1
1.1 前言 .......................................................................................................................... 1
1.2 顆粒床系統簡介 ...................................................................................................... 4
1.3 焦油介紹 .................................................................................................................. 4
1.4 文獻回顧 .................................................................................................................. 5
1.5 研究動機與目的 .................................................................................................... 10
1.6 論文章節架構 ........................................................................................................ 10
第二章 實驗設備與方法 ........................................................................................................ 20
2.1 中高溫除塵實驗設備與方法 ................................................................................ 20
2.1.1 實驗濾材及量測設備 ................................................................................. 20
2.1.2 實驗設備 ..................................................................................................... 21
2.1.3 過濾機制 ..................................................................................................... 23
2.1.4 過濾行為 ..................................................................................................... 25
2.1.5 實驗參數 ..................................................................................................... 26
2.1.6 實驗步驟 ..................................................................................................... 27
2.2 中高溫除焦油實驗設備與方法 ............................................................................ 29
2.2.1 實驗材料及量測儀器 ................................................................................. 29
VI
2.2.2 實驗設備 ..................................................................................................... 30
2.2.3 過濾機制 ..................................................................................................... 32
2.2.4 實驗參數 ..................................................................................................... 32
2.2.5 實驗步驟 ..................................................................................................... 34
第三章 實驗結果與討論 ........................................................................................................ 43
3.1 中高溫除塵實驗結果與討論 ................................................................................ 43
3.1.1 壓差變化 ..................................................................................................... 43
3.1.2 溫度及溫差變化 ......................................................................................... 44
3.1.3 過濾效率 ..................................................................................................... 45
3.2 中高溫除焦油實驗方法驗證 ................................................................................ 47
第四章 結論 ............................................................................................................................ 57
第五章 參考文獻 .................................................................................................................... 58參考文獻 [1] IPCC, 氣候變化 2014 綜合報告, 政府間氣候變化專門委員會, 瑞士日内瓦,
2015.
[2] 台灣電力公司, 發電資訊, 電力供需資訊_電源開發規劃_歷年發電量及結構,
1996-2016.
[3] 姚向君, 田宜水，生質能源 : 綠色黃金開發技術，一版，新文京開發出版股份
有限公司，台北，民國九十七年
[4] G. Xiao, X. Wang, J. Zhang, M. Ni, X. Gao, Z. Luo and K. Cen,
“A Promising Technology for Hot Gas Clean-Up”, Powder Technology, Vol. 244, pp.
93–99, 2013.
[5] R. C. Flagan, J. H. Seinfeld, “Fundamentals of air pollution Engineering”, Prentice-
Hall, Inc. 1998.
[6] Kaufmann, E., Bouman, D., Theunis, A., Kleiberg, X., Megen, R. van, “Black Carbon
Reduction”, Rotterdam Mainport University of Applied and Sciences, 2014.
[7] H. Zhang, G. Ahmadi, “Particle transport and deposition in the hot-gas filter vessel
at Wilsonville”, Powder Technology, Vol. 116, pp. 53–68, 2001.
[8] Y. S. Chen, S. S. Hsiau, S. C. Laia, Y. P. Chyoub, H. Y. Lia and C. J. Hsu,
“Filtration of dust particulates with a moving granular bed filter”, Vol 171, pp. 987-
994, 2009.
[9] S.S. Hsiau, J. Smid, C.Y. Wang, J.T. Kuo and Chou, C.S.
“Velocity Profiles of Granules in Moving Bed Filters”, Chemical Engineering
Science, Vol. 54, pp. 293-301, 1999.
[10] C. Li, and K. Suzuki, “Tar property, analysis, reforming mechanism and model for
biomass gasification—An overview”, Renewable and Sustainable Energy Reviews,
Vol 13, pp. 594-604, 2009.
59
[11] E.G. Baker, M.D. Brown, D.C. Elliott and L.K. Mudge, “Characterization and
Treatment of Tars from Biomass Gasifiers”, Denver, CO: AIChE 1988 Summer
National Meeting, pp. 1–11.
[12] H. Boerrigter, S.V.B. van Paasen, P.C.A. Bergman, J.W. Könemann, R. Emmen and
A. Wijnands, “OLGA” TAR REMOVAL TECHNOLOGY, ECN, 2005.
[13] P. Basu, (Third Edition) “Biomass Gasification, Pyrolysis and Torrefaction”
Academic press, Halifax, NS, Canada, 2018.
[14] J.T. Kuo, J. Smid, S.S. Hsiau, C.Y. Wang and C.S. Chou, “Stagnant zones in granular
moving bed filters for flue gas cleanup”, Filtration and Separation, Vol 35, pp. 529-
534, 1998.
[15] S.S. Hsiau, J. Smid, F.H. Tsai, J.T. Kuo and C.S. Chou, “Placement of flow-corrective
elements in a moving granular bed with louvered-walls”, Chemical Engineering and
Processing, Vol 43, pp. 1037-1045, 2004.
[16] J.R. Johanson, “The Use of Flow Corrective Inserts in Bins”, Engineering for
Industry-Transactions of the ASME”, Vol. 88, pp. 224-230, 1966.
[17] J.R. Johanson, and W.K. Kleysteuber, “Flow Corrective Inserts in Bins”, Chemical
Engineering Progress, Vol. 62, pp. 79-83, 1966.
[18] J.R. Johanson, “The Placement of Insert to Correct Flow Problems”, Powder
Technology, Vol. 1, pp. 328-333, 1967.
[19] 古政芳，「流動式顆粒床過濾器阻礙物配置之設計」，
國立中央大學，碩士論文，民國八十九年。
[20] 林政煌，「流動式顆粒床過濾器之流場型態設計與研究」，
國立中央大學，碩士論文，民國九十三年。
[21] 高偉智，「流動式顆粒床過濾器之流動校正單元設計與分析究」，
國立中央大學，碩士論文，民國九十四年。
60
[22] 陳一順，「流動式顆粒床過濾器三維流場觀察與冷性能測試」，
國立中央大學，碩士論文，民國九十年。
[23] 馬家駒，「流動式顆粒床過濾器冷性能測試」，
國立中央大學，碩士論文，民國九十一年。
[24] 賴信璋，「流動式顆粒床過濾器過濾機制研究」，
國立中央大學，碩士論文，民國九十二年。
[25] 陳一順，「流動式顆粒床過濾器之濾餅機制行為研究」，
國立中央大學，博士論文，民國九十八年。
[26] 蔡信安，「流動式顆粒床過濾器之雙葉片型流動校正單元設計與冷性能過濾機
制研究」，國立中央大學，碩士論文，民國九十五年。
[27] 許嘉仁，「移動式顆粒床過濾器進風口氣體流場行為與過濾性能之研究」，
國立中央大學，碩士論文，民國一 OO 年。
[28] 張益綸，「顆粒床過濾連續化整合系統開發研究」，
國立中央大學，碩士論文，民國一 O 二年。
[29] 許展瑞，「顆粒床整合系統最適化設計與連續過濾驗證之研究」，
國立中央大學，碩士論文，民國一 O 四年。
[30] 許端佑，「移動式顆粒床之進口粉塵濃度與再生循環對過濾效率的影響」，
國立中央大學，碩士論文，民國一 O 六年。
[31] 王超，「垃圾中轉站滾筒篩的設計及動態仿真研究」，
北京機械工業學院，碩士論文，民國九十四年。
[32] 李宣億，「流動式顆粒床過濾器之滾筒式粉塵分離系筒與冷性能過濾及破碎效
應研究」，國立中央大學，碩士論文，民國九十七年。
[33] 紀克彥，「顆粒床過濾器濾材粉塵振動篩分之研究」，
國立中央大學，碩士論文，民國九十四年。
61
[34] Y. S. Chen, Y. P. Chyou and S. C. Li, “Hot gas clean-up technology of dust particulates
with a moving granular bed filter”, Applied Thermal Engineering, Vol 74, pp. 146-
155, 2014.
[35] L. Fagbemi, L. Khezami and R. Capart, “Pyrolysis products from different biomasses:
application to the thermal cracking of tar”, Applied Energy, Vol 69, pp. 293-306, 2001.
[36] G.G. Alberto, S.P. Javier , S.V. Antonio and S. Domingo, “Moving bed syngas
conditioning: Modelling”, Applied Thermal Engineering, Vol 62, pp. 809-822, 2014.
[37] ECN: “Thersites the ECN tar dew point site”
http://www.thersites.nl/completemodel.aspx
[38] S.Y. Liu, D.H. Mei, L. Wang, X. Tu, “Steam reforming of toluene as biomass tar
model compound in a gliding arc discharge reactor”, Chemical Engineering, Vol 166,
pp. 269-275, 2017.
[39] M. Morgalla, L. Lin, M. Strand, “Decomposition of benzene using char aerosol
particles dispersed in a high-temperature filter”, Energy, Vol 118, pp. 1345-1352,
2017.
[40] J. Good, L. Ventress, H. Knoef, U. Zielke, P. Lyck Hansen, W. van de Kamp, P. de
Wild, B. Coda, S. van Paasen, J. Kiel, K. Sjöström, T. Liliedahl, Ch. Unger, J. Neeft,
M. Suomalainen and P. Simell, “Sampling and analysis of tar and particles in biomass
producer gases-Technical Report”, CEN BT/TF 143, July 2005.
[41] 馬勝銘，「循環式顆粒床過濾器過濾性能研究」，國立中央大學，
碩士論文，民國九十三年。
[42] W. Peukert and F. Loffler, “Influence of temperature on particle separation
in granular bed filters”, Powder Technology, Vol 68, pp. 263-270, 1991指導教授 蕭述三(Shu-San Hsiau) 審核日期 2018-10-18 推文 plurk
funp
live
udn
HD
myshare
netvibes
friend
youpush
delicious
baidu
網路書籤 Google bookmarks
del.icio.us
hemidemi
facebook
twitter
google
reddit