摘要(英) |
With the advancement of technology, more stringent regulation in environmental protection and the trend of implementing circular economy policies, how to recycle valuable metals from fly ash has become a big challenge. The aim of this study is to evaluate the effectiveness of electric smelting reduction furnace (ESRF) to recover valuable metals from the fly ash collected from stainless steel industry. Analysis of the compositions of stainless steel fly ash indicates that four elements including iron, chromium, nickel, and zinc, are of the most recovery value; and they account for 30-68% of the total compositions. The granulated pellet of ash is put into the electric smelting reduction furnace with a temperature of 1550℃ and reducing agent such as coke is applied to reduce the metallic oxide in the fly ash to recover iron, chromium, nickel, and zinc. Moreover, the impact of varying basicity on the recovery rate of of the targent metals is also evaluated and the results reveal that the best recovery rates of iron, chromium, and nickel can be obtained if the basicity is controlled at 1-1.09. The recovery rates of iron, chromium, and nickel reach≧90%. The results of toxicity characteristic leaching procedure (TCLP) reveal that leaching concentrations of nickel and chromium are 0.16 and 0.1 mg/L, respectively. The results also indicate that as the basicity is controlled between 1.1 and 1.3, the leaching concentrations of nickel and chromium are the lowest, demonstrating that operation under this condition results in the best stability of slag. Analysis of the ash collected by baghouse during manufacturing process reveals the zinc oxide content in the secondary ash is around 34%. The total solid input for the test run is 2175 tons with the total output of 1158 ton. The decrease in mass is caused by the oxidation and reduction of metallic oxide in ESRF, which turn into CO2 and is discharged into the atmosphere. The electricity consumed for treating one ton of stainless steel fly ash is 3050 kWh, indicating that the process is energy-intensive. How to reduce electricity consumption and reduce operating cost remains a big challenge. Overall the result reveals the electric smelting reduction furnace can effectively recycle valuable metals from stainless steel ash and this process can turn stainless steel fly ash into harmless, recyclable, and reusable products. |
參考文獻 |
〔1〕 徐德弦,國立中央大學環境工程研究所,「以高溫熔融還原法回收不銹鋼集塵灰中鉻與鎳之效益探討」,2015。
〔2〕 廖耀宇,認識不銹鋼,技師期刊6465合輯。
〔3〕 許明宏,「ESRF熔融爐操作實務」,嘉德創資源股份有限公司訓練教材,2012。
〔4〕 電弧爐煉鋼業環保工安整合性技術手冊,經濟部工業局,2000。
〔5〕 林柏謙,資料彙整:華南期貨分析師。
〔6〕 劉文海,「台灣常用爐石與工程應用實務」,產業報,第93期,2014。
〔7〕 倫敦金屬交易所-鎳。
〔8〕 美國地質調查局 (USGS) baike.asianmetal.cn.
〔9〕 世界主要礦產資源儲藏和生產情況簡介.中國稀有金屬網。
〔10〕 黃清連、吳裕慶,鋅之冶煉法與資源再生,98年12月。
〔11〕 金琳,「世界不銹鋼市場分析」,冶金管理,第8期,冶金信息標準研究院,2004。
〔12〕 鋼鐵行業對低碳未?的貢獻國際鋼鐵協會行動報告,2014年3月。
〔13〕 段建平、張永亮、李宏、王建昌,「電爐直接利用Cr-Ni不銹鋼除塵灰的試驗分析」,鋼鐵,第44卷第5期,2009年5月。
〔14〕 劉瓊芳,回收電爐集塵灰有價物質之技術介紹,工研院環安中心,廢棄物處理與資源化研究組。
〔15〕 何春松、謝聖嫄,高溫熔融還原法回收煉鋼集塵灰中之有價金屬,嘉德技術開發股份有限公司,2011。
〔16〕 林於隆,「爐渣(Slag)」嘉德創資源股份有限公司技術會議,2012。
〔17〕 何春松、謝聖嫄,「高溫熔融還原法回收煉鋼集塵灰中之有價金屬」,區域與環境資源永續發展研討會,2011。
〔18〕 IOSH103-T-141鋼鐵業安全衛生危害風險評估與控制技術手冊 page 3~6。
〔19〕 Kenneth, E.C.,“A Review of New Furnace Technologies.”Iron and Steel Engineer, pp. 45-47, 1983.
〔20〕 Kishida, T., Yuasa, G., Shiina, K.,“Energy Saving Technology of Electric Furnace Steelmaking in Japan.”SEAISI Quarterly , pp. 48-50, 1987.
〔21〕 經濟部工業局100 年度「中小企業工作環境改善計畫」鋼鐵業風險評估案例實務手冊page 4。
〔22〕 鄭福田,洪文龍,“電弧爐煉鋼粒狀污染物排放係數調查”工業污染防治,第8卷第5期,pp.50-59,1989。
〔23〕 林凱悅,國立中央大學土木工程學系碩士論文-鐵礦碴再利用於鋪面工程之研究,2011年page 7、8 。
〔24〕 經濟部工業局100年度「中小企業工作環境改善計畫」鋼鐵業風險評估案例實務手冊,page 7~8。
〔25〕 102年度製造業原物料耗用通常水準調查報告「鋼鐵業調查報告」,財政部中區國稅局,P34。
〔26〕 電弧爐煉鋼業環保工安整合性技術手冊,經濟部工業局,14-29頁,2000。
〔27〕 佘承璋,國立屏東科技大學環境工程與科學系,不銹鋼二次集塵灰之再利用研究,96年6月。
〔28〕 ?本博彥,「電???????理技術?研究」,日本東北大學,博士論文,2003。
〔29〕 李京社、朱經濤、楊宏博、楊樹峰,「中國電爐煉鋼粉塵處理現狀」,河南治金,第19卷第4期,2011年8月。
〔30〕 Xia D. K., Pickles C.A., Minerals Engineering, 13 (Compendex), pp.79, 2000.
〔31〕 Davis J.R.& Associates, Surface Engineering of Stainless Steel, ASM Handbooks, Surface Engineering, Vol.5 , pp. 740, 1994.
〔32〕 吳銘誠,「不銹鋼電弧爐氧化渣之再利用研究」,高雄應用科技大學,碩士論文,民國92年。
〔33〕 陳慧君,「台灣不鏽鋼品需求預測之研究」,靜宜大學在職專班,碩士論文,民國96年6月。
〔34〕 沈永年、盧俊文,「含不銹鋼集塵灰瓷磚之工程性質研究」,臺灣?業,第 62 卷第 1 期,2010。
〔35〕 彭兵、彭及,「不銹鋼電弧爐粉塵的物理化學特性及形成機理探討」,北方工業大學學報,第15卷第1期,2003。
〔36〕 馬國軍、蘇偉厚、薛正良、徐之浩,「不銹鋼廠煙塵的微觀結構及其中鉻的賦存形式」,中國鋼鐵年會論文集,152?157頁,2009。
〔37〕 馬國軍、范巍、徐之浩等,「不銹鋼廠煙塵中鉻及其他元素的分布規律」,過程工程學報,第S1期,68?71頁,2010。
〔38〕 魏芬絨、張延玲、魏文洁、楊小剛,「不銹鋼粉塵化學組成及其Cr、Ni存在形態」,過程工程學報,第11卷第5期,2011。
〔39〕 Guezennec, A.G., Huber, J.C., Patisson, F., Sessiecq, P., Birat, J.P., Ablitzer, D.,“Dust Formation in Electric Arc Furnace: Birth of The Particles”,Powder Technology, Vol. 157, pp. 2?11, 2005.
〔40〕 佘承璋,國立屏東科技大學環境工程與科學系,不銹鋼二次集塵灰之再利用研究, 96年6月。
〔41〕 Pickles, C. A.,“Thermodynamic Analysis of the Separation of Zinc and Lead From Electric Arc Furnace Dust by Selective Reduction with Metallic Iron〔J〕”, Separation and Purification Technology, 2008。
〔42〕 楊金鐘,「固化及穩定化技術於廢棄物處理之應用」,化工技術,138-148頁,1995。
〔43〕 李偉立,「達成鋼鐵業事業廢棄物零廢棄願景-鋼鐵業集塵灰資源化研究」,屏東縣環境保護局,出國報告,民國95年。
〔44〕 宋海琛、彭兵,「不銹鋼粉塵綜合利用現狀及研究進展」。
〔45〕 礦產綜合利用,第3期,2004年6月。
〔46〕 世界鋼鐵工會統計數據 2016。
〔47〕 吳文龍,「鋼鐵基本工業、鋁熔煉業集塵灰及事業污泥清理查核專案工作計畫」,行政院環境保護署計畫成果,中興工程顧問股份有限公司,民國103年。
〔48〕 台灣鋼鐵工業同業公會。
〔49〕 許明宏,電熱熔融還原爐直接回收煉鋼集塵灰中的有價金屬,材資系教育基金會會刊第 7 期。
〔50〕 朝陽科技大學環境工程與管理系,利用超臨界流體去除鋼鐵業集塵灰中多環芳香烴“芘”之研究,孫立明,97年6月。
〔51〕 劉瓊芳,「回收電爐集塵灰有價物質之技術介紹」,環安簡訊電子報,第57期,2005。
〔52〕 Lynn, J., “Process for Chemical Stabilisation of Heavy Metal Bearing Dust and Sludges, such as EAF Dust”, International Patent PCT/US 88/01879, Bethlehem Steel Corp, 1988.
〔53〕 Evans, L.G., Hogan, J.C., “Recycling of EAF Dust by Direct Injection”, Electric Furnace Conference Proceedings, vol. 44, pp. 367, 1987.
〔54〕 「鋼鐵業廢棄物資源化案例彙編」,經濟部工業局編,1996。
〔55〕 曹申,「提煉冶金技術與電爐集塵灰」,環安簡訊電子報,第57 期,1999。
〔56〕 李宗立,「電弧煉鋼煙塵之性質與資源化之研究」,成功大學礦冶及材料科學研究所,博士論文,1993。
〔57〕 傅崇德,桃園縣大學校院產業環保技術團,淺談溼式淬取法應用於電鍍汙泥中有價金屬之回收處理,環保簡訊/第22期。
〔58〕 鋼鐵基本工業、鋁熔煉業集塵灰及事業污泥清理查核專案工作計畫,2012。
〔59〕 楊錕池,「電弧爐碳鋼集塵灰資源化介紹」,台灣鋼聯,2005。
〔60〕 台灣鋼聯股份有限公司網頁旋轉窯高溫冶煉製程說明。
〔61〕 彭慶廣,「碳鋼煙塵脫氯及資源化製備奈米氧化鋅之研究」,國立臺北科技大學,碩士論文,2006。
〔62〕 BEFESA,中國不銹鋼協會年會簡報,北京,中國,2011。
〔63〕 嘉德技術開發股份有限公司工程技術中心,「電華新麗華不銹鋼廠電爐集塵灰熔融處理實驗計劃」,1999。
〔64〕 林志杰,「應用電弧爐氧化碴於高性能低強度材料之研究」,私立淡江大學,碩士論文,2004。
〔65〕 村上忠弘, 石田貴榮, “水道污泥灰分?熔融特性?關??考察”, 下水道協會誌, Vol. 26, No. 296, 1989.
〔66〕 倪文、李建平、方興、陳德平、陳那那,礦物材料學導論,科學出版社,33-34頁,1998。
〔67〕 廖錦聰、張蕙蘭、徐文慶、黃契儒,「垃圾焚化底灰之資源化利用」,一般廢棄物焚化灰渣資源化技術與實務研討會,第131-146頁,台北,1996。
〔68〕 Laforest G., Duchesne J., “Characterization and Leachability of Electric Arc Furnace Dust Made from Remelting of Stainless Steel”, Journal of Hazardous Materials, B, 135, pp. 156–164, 2006.
〔69〕 胡金龍,「鋁熱反應回收有害集塵灰及污泥中有價金屬之研究」,國立雲林科技大學,碩士論文,2012。
〔70〕 Tahir S., Alenka R.M., ?tefica C.S., Vjera R.N., Monika J.,“Characterization of Steel Mill Electric-arc Furnace Dust”, Journal Haradous Materials, Vol.109, No.1-3, pp.59-70. 2004.
〔71〕 蔡敏行,「煉鋼煙塵之現況與資源化技術」,環保月刊,98-113頁,2001。
〔72〕 Mikhail S.A., Turcotte A.M., Aota, J.,“Thermoanalytical Study of EAF Dust and Its Vitrification Product”, Thermochimica Acta, Vol.287, Issue:1, pp.71-79,1996.
〔73〕 蔡柏棋、徐登科,「台灣常用爐石與工程應用實務」,技師報,第938期,2014年11月。
〔74〕 Zunkel, D., “What to Do with Your EAF Dust, Steel Times International, pp. 46–56, 1996. |