參考文獻 |
[1] 中聯資源股份有限公司:《轉爐石瀝青混凝土使用手冊》,高雄市:中聯資源股份有限公司,2017。
[2] 王睿懋:〈亞熱帶地區提升再生瀝青混凝土耐久性之研究〉。碩士論文,國立中央大學,2009。
[3] 行政院經濟部標準檢驗局:《CNS 486粗細粒料篩析法》,台北市:行政院經濟部標準檢驗局,2011。
[4] 行政院經濟部標準檢驗局:《CNS 487細粒料密度、相對密度(比重)及吸水率試驗法》,台北市:行政院經濟部標準檢驗局,2013。
[5] 行政院經濟部標準檢驗局:《CNS 488粗粒料密度、相對密度(比重)及吸水率試驗法》,台北市:行政院經濟部標準檢驗局,2008。
[6] 行政院經濟部標準檢驗局:《CNS 3483石油產品賽氏黏度試驗法》,台北市:行政院經濟部標準檢驗局,2009。
[7] 行政院經濟部標準檢驗局:《CNS 10090瀝青/柏油針入度試驗法》,台北市:行政院經濟部標準檢驗局,2009。
[8] 行政院經濟部標準檢驗局:《CNS 10091瀝青延性試驗法》,台北市:行政院經濟部標準檢驗局,2009。
[9] 行政院經濟部標準檢驗局:《CNS 10367乳化瀝青篩析試驗法》,台北市:行政院經濟部標準檢驗局,2008。
[10] 行政院經濟部標準檢驗局:《CNS 10456乳化瀝青蒸發殘渣量試驗法》,台北市:行政院經濟部標準檢驗局,2008。
[11] 行政院經濟部標準檢驗局:《CNS 10989粒料樣品減量為試驗樣品取樣法》,台北市:行政院經濟部標準檢驗局,2015。
[12] 行政院經濟部標準檢驗局:《CNS 12017原油及液體石油產品密度、相對密度(比重)、API比重試驗試驗法(比重計法)》,台北市:行政院經濟部標準檢驗局,2016。
[13] 行政院經濟部標準檢驗局:《CNS 14186無填充料瀝青黏度測定法(布魯克熱力黏度計法)》,台北市:行政院經濟部標準檢驗局,1998。
[14] 行政院經濟部標準檢驗局:《CNS 15310 瀝青鋪面混合料用鋼爐碴粒料》,台北市:行政院經濟部標準檢驗局,2010。
[15] 行政院經濟部標準檢驗局:《CNS 15476半固態瀝青材料密度試驗法》,台北市:行政院經濟部標準檢驗局,2011。
[16] 行政院公共工程委員會:《施工綱要規範第02742章瀝青混凝土鋪面V11.0》,台北市:行政院公共工程委員會,2019。
[17] 行政院公共工程委員會:《施工綱要規範第02747章瀝青黏層V3.0》,台北市:行政院公共工程委員會,2018。
[18] 行政院公共工程委員會:《施工綱要規範第02966章再生瀝青混凝土鋪面V7.0》,台北市:行政院公共工程委員會,2013。
[19] 何鴻文、朱建東、洪明澤、陳志明:〈瀝青膠泥不同分級系統適用性之研究〉,《台灣公路工程》,第42卷第12期,27~44頁,2016年12月。
[20] 吳建宏:〈含轉爐石刨除料應用於再生瀝青混凝土成效評估〉。碩士論文,國立中央大學,2019。
[21] 林登峰、陳筠昀、蔡昕融、王美雲:〈探討轉爐石瀝青混凝土試驗道路成果-以高雄市大業北路為例〉,《2012年轉爐石瀝青混凝土研討會》,79~103頁,2012年。
[22] 施淞育:〈轉爐石刨除料應用於再生瀝青混凝土之研究〉。碩士論文,私立義守大學,2014。
[23] 陳世晃:〈台灣鋪面(Taipave)配比設計法之初擬〉。博士論文,國立中央大學,2003年6月。
[24] 陳世晃:《中龍精整西路鋪設轉爐石瀝青混凝土鋪面之成效評估-期末報告書》,桃園市:國立中央大學,2016。
[25] 陳世晃:《含轉爐石刨除料之再生瀝青混凝土體積性質與抗水分侵害之成效評估(II)》,桃園市:國立中央大學,2019。
[26] 郭旻叡:〈含不同黏層材料與養護條件對於瀝青混凝土剪切強度之影響〉。碩士論文,國立中央大學,2020。
[27] 張宸翔:〈鋪面型式及黏層用量對層間黏結力之數值分析〉。碩士論文,國立高雄第一科技大學,2018。
[28] 黃大衛:〈爐石取代傳統粒料對瀝青混凝土VMA性質影響之研究〉。碩士論文,國立中央大學,2008。
[29] 詹謦聯:〈氧化碴應用於密集配瀝青混凝土實驗室成效分析〉。碩士論文,國立中央大學,2019。
[30] A. J. T. Hand and T. B. Aschenbrener, “Successful Use of Reclaimed Asphalt Pavement in Asphalt Mixture.” WRSC-TR-21-10, Transportation Research Board, 2021.
[31] American Association of State Highway and Transportation Officials, “AASHTO R 30 Standard Practice for Mixture Conditioning of Hot Mix Asphalt (HMA).”
[32] American Association of State Highway and Transportation Officials, “AASHTO T 283-21 Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage.”
[33] American Association of State Highway and Transportation Officials, “AASHTO T 324 (Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures).”
[34] American Society for Testing and Materials International, “ASTM D6931-12 Standard Test Method for Indirect Tensile (IDT) Strength of Bituminous Mixtures.
[35] American Society for Testing and Materials International, “ASTM D3625-20 Standard Practice for Effect of Water on Asphalt-Coated Aggregate Using Boiling Water.”
[36] American Society for Testing and Materials International, “ASTM D3625-20 Standard Practice for Effect of Water on Asphalt-Coated Aggregate Using Boiling Water.”
[37] Asphalt Institute, “MS-2 Asphalt Mix Design Methods.” 7 Edition, 2014.
[38] A. Varveri, S. Avgerinopoulos, A. Scarpas, A. Collop and S. Erkens, “On the Combined Effect of Moisture Diffusion and Cyclic Pore Pressure Generation in Asphalt Concrete.”, 93rd TRB Annual Meeying Compendium of Papers, Washington, D.C., July 2013.
[39] A. Varveri, J. Zhu, and N. Kringos, “Moisture damage in asphalt mixtures.” Advances in Asphalt Materials, pp.303-344, 2015.
[40] B. R. Christopher, C. Schwartz, & R. Boudreau, “Geotechnical Aspects of Pavements.” Washington, D.C.:Federal Highway Administration, May 2006.
[41] B. Sengoz & E. Agar, “Effect of asphalt film thickness on the moisture sensitivity characteristics of hot-mix asphalt.” Building and Environment, Vol 238, pp.3621-3628, 2007.
[42] H. Bahia, P. Teymouropur, D. Swiertz, C. Ling, R. Varma, T. Mandal, P. Chaturabong, E. Lyngdal, & A. Hanz, “Analysis and Feasibility of Asphalt Pavement Performance-Based Specifications for WisDOT.” Wisconsin Highway Research Program 92-15-04, 2016.
[43] L.N. Mohammad, M.a. Elseifi, A. Bae, & N. Patel, “Optimization of Tack Coat for HMA Placement.” Report No. NCHRP 712, Transportation Research Board, Washington, D.C., 2012.
[44] Illinois Department of Transportation, “Standard Specifications for Road and Bridge Construction”, April, 2016
[45] J. S. Chen andf C. C. Huang, “Effect of surface characteristics on bonding properties of bituminous tack coat.” Transportation Research Record: Journal of the Transportation Research Board, Vol 218, , pp.142-149, 2010.
[46] J. Xie, C. Yang, L. Zhang, X. Zhou, S. Wu, & Q. Ye, “Investigation of the physic-chemical properties and toxic potential of Basic Oxygen Furnace Slag (BOF) in asphalt pavement constructed after 15 years.” Construction and Building Materials, Vol 238, 2020.
[47] J. Wang, F. Xiao, Z. Chen, X, Li, & S. Amirkhanian, “Application of tack coat in pavement engineering.” Construction and Building Materials, pp. Vol 152, pp. 856-871, 2017.
[48] M. A. Taylr & N. P. Khosla, “Stripping of Asphalt Pavements: State of the Art.” Transportation Research Record 911, pp. 150-158, 1983.
[49] M. M. Hasan & R. A. Tarefder, “Development of rutting specifications and possible replacement of tensile strength ratio by Hamburg wheel tracking device test.” International Journal of Pavement Engineering, 2020.
[50] Montana Department of Transportation and the Montana Transportation Commission, “Standard Specifications for Road and Bridge Construction”, 2014.
[51] N. Kringos, A. Scrarpas, A. Copeland, & J. Youtcheff, “Modeling of combined physical–mechanical moisture induced damage in asphaltic mixes.” International Journal of Pavement Engineering, Vol 9, pp. 115-128, 2007.
[52] P. Chaturabong & H. U. Bahia, “Development of rutting specifications and possible replacement of tensile strength ratio by Hamburg wheel tracking device test.” Construction and Building Materials, Vol 153, pp. 337-345, 2017.
[53] Q. Lv, W. Huang, M. Zheng, H. Sadek, Y. Zhang, & C. Yan, “Influence of gradation on asphalt mix rutting resistance measured by Hamburg Wheel Tracking test.” Construction and Building Materials, Vol 238, 2020.
[54] State of California State Transportation Agency Department of Transportation,“Standard Specifications”, 2015.
[55] Washington State Department of Transportation,“Standard Specifications for Road, Bridge, and Municipal Construction M 41-10”, 2022.
[56] Z. Chen, J. Xie, Y. Xiao, J. Chen, & S. Wu, “Characteristics of bonding behavior between basic oxygen furnace slag and asphalt binder.” Construction and Building Materials, Vol 64, pp.60-66, 2014. |