博碩士論文 110322030 詳細資訊




以作者查詢圖書館館藏 以作者查詢臺灣博碩士 以作者查詢全國書目 勘誤回報 、線上人數:64 、訪客IP:3.17.77.161
姓名 張若軒(Jo-Hsuan Chang)  查詢紙本館藏   畢業系所 土木工程學系
論文名稱 橋梁健康監測之診斷分析
(Diagnostic Analysis of Bridge Health Monitoring)
相關論文
★ 貼片補強構件之層間應力分析★ 軌道不整檢測及識別方法
★ 混凝土結構分析之三維等效單軸組成材料模型★ 卵形顆粒法向與切向接觸之等效線性彈簧值之推導與驗證
★ 以四面體離散化多面體系統之接觸分析與模擬★ 軌道車輛三維動態脫軌係數之在線量測理論
★ 向量式DKMT厚殼元推導與模擬★ 向量式預力混凝土二維剛架元之數值模擬與驗證
★ 向量式有限元應用於懸索橋非線性動力分析★ 蛋形顆粒群之流固耦合分析
★ 複合版梁元素分析模型之橋梁動態識別法★ 三維等效單軸應變與應力之材料組成模型
★ 人行吊橋的現有內力評估及動力分析★ 薄殼結構非線性運動之向量式有限元分析法
★ 雷射掃描技術於鋼軌磨耗之檢測★ 動態加載下的等效單軸應變與 應力材料組成模型
檔案 [Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   至系統瀏覽論文 ( 永不開放)
摘要(中) 南方澳大橋於民國108年10月1日上午發生橋身突然倒塌的事件,突顯橋梁安全維護的重要性,關渡大橋目前橋齡已超過40年,橋梁服務性及安全在下列情況可能存在疑慮,因此本研究針對橋體結構及纜索作數值模擬。
文獻回顧內容包含索力計算方法、關渡大橋纜索之結構及其材料性質,以進行後續建模及數值驗證。
索力分析中第一部分為彎曲剛度分析,模擬纜索在不同角度下受彎矩作用後的彎曲剛度,最後整理出平均值,並將結果用於後續模擬;第二部分為研究纜索各構件對頻率的影響,將纜索模型分為4個類型,比較不同模型下的頻率差異,以決定後續全橋模型中纜索的簡化方式。
全橋分析根據關渡大橋竣工圖建立數值模型,流程包括以Solid Works建出外觀,Hyper Mesh切出網格元素,Ls-Dyna輸入材料、結構構件的定義及邊界條件設定。分析包含模態分析、靜載分析、溫度分析、地震力分析。模態分析初步確認模型是否有誤,以及得到關渡橋之自然模態頻率。靜載分析中先模擬無施加索力的分析,取得纜索因橋拱及主梁受重力變形後所造成的索力,與監測數據做比較,藉以判斷監測數據的正確性;後為模擬施加索力的分析,以監測索力為目標索力對模型進行調整,模擬現今監測索力及重力對橋體變形的影響。溫度分析概念為排除車載,溫度對監測索力的影響,因此取凌晨時段之監測數據,再由該部分的數據中取相對高溫及低溫的數據,比較溫度對實際監測的影響,後於模型中數據對應之溫度,比較有限元模型模擬出之數據是否對應監測數據。
摘要(英) The Nanfang′ao Bridge suddenly collapsed on the morning of October 1, 2018, highlighting the importance of bridge safety maintenance. The Guandu Bridge is currently over 40 years old, and the serviceability and safety of the bridge may be questionable under the following circumstances. The research conducts numerical simulations on the bridge structure and cables.
The literature review includes the cable force calculation method, the structure of the cable and its material properties for subsequent modeling and numerical verification.
The first part of the cable force analysis is the bending stiffness analysis, which simulates the bending stiffness of the cable after being subjected to bending moments at different angles. Finally, the average value is compiled and the results are used for subsequent simulations; the second part is the study of the frequency response of each component of the cable. The cable model is divided into 4 types, and the frequency differences under different models are compared to determine the simplification method of the cable in the subsequent full-bridge model.
The full bridge analysis establishes a numerical model based on the as-built drawings of the Guandu Bridge. The process includes using Solid Works to create the appearance, Hyper Mesh to cut out the mesh elements, and Ls-Dyna to input the definition of materials, structural components, and boundary condition settings. The analysis includes modal analysis, static load analysis, temperature analysis, and seismic force analysis. Modal analysis preliminarily confirms whether the model is correct and obtains the natural modal frequency of Guandu Bridge. In the static load analysis, the analysis without applied cable force is first simulated, and the cable force caused by the gravity deformation of the bridge arch and main beam is obtained, and compared with the monitoring data to judge the correctness of the monitoring data; then the cable force is simulated for the simulation. Force analysis, the model is adjusted with the monitoring cable force as the target cable force, and the influence of the current monitoring cable force and gravity on the bridge deformation is simulated. The concept of temperature analysis is to exclude the influence of vehicle temperature on the monitoring cable force. Therefore, the monitoring data in the early morning period are taken, and then the relatively high and low temperature data are taken from this part of the data to compare the impact of temperature on the actual monitoring, and then in the model The temperature corresponding to the data is compared to see whether the data simulated by the finite element model corresponds to the monitoring data.
關鍵字(中) ★ 橋梁
★ 結構間康診斷
★ 有限元分析
關鍵字(英)
論文目次 摘要 i
Abstract ii
致謝 iv
目錄 v
圖目錄 ix
表目錄 xvi
第一章 緒論 1
1-1 前言 1
1-2 研究動機 1
1-3 研究方法 2
1-4 論文架構 3
第二章 文獻回顧 5
2-1 關渡大橋基本介紹 5
2-2 關渡大橋之吊索更換 5
2-2-1 吊索之配置 6
2-2-2 關渡大橋新吊索之組成 8
2-2-3 新舊吊索比較 8
2-2-4 換索過程 11
2-3 簡支拉力梁理論 13
2-4 纜索及橋體之數值分析 15
第三章 纜索之有限元模擬分析 18
3-1 鋼纜彎曲剛度的模擬 18
3-1-1 細部纜索模型之建立 20
3-1-2 材料參數 23
3-1-3 模擬設定 24
3-1-4 彎曲剛度之計算 24
3-1-5 模擬結果 25
3-2 建立纜索之模型 39
3-2-1 纜索 41
3-2-2 上錨 42
3-2-3 防雨罩及制震器 43
3-3 材料參數 45
3-3-1 纜索 45
3-3-2 上錨 46
3-3-3 防雨罩及制震器 46
3-4 纜索邊界條件之設定 47
3-5 元素之收斂性 50
3-6 各構件對頻率影響的分析比較 53
3-6-1 CASE 1 54
3-6-2 CASE 2 56
3-6-3 CASE 3 57
3-6-4 CASE 4 59
3-6-5 CASE 5 60
3-6-6 比較數值 61
第四章 全橋之有限元模擬分析 62
4-1 橋梁之結構 62
4-2 建立模型 69
4.3 材料參數 77
4-4 支承設定 78
4-5 邊界條件 80
4-6 監測儀器 81
4-6-1 纜索加速度計 81
4-6-2 溫度計 82
4-7 模態分析 84
4-7-1 結構補強前 84
4-7-2 結構補強後 86
4.8 靜載分析 88
4-8-1 無設定索力之靜載模擬 88
4-8-2 設定索力之靜載模擬 93
4-9 溫度分析 103
4-9-1 溫度之監測數據 103
4-9-2 模型之溫度設定 110
4-9-3 溫度分析結果 111
第五章 結論與建議 120
5-1 結論 120
5-2 建議 121
文獻參考 122
參考文獻 1. 99吊索更換施工計畫書及預力導入計算書,交通部公路總局,民國99年10月。
2. 關渡橋主橋新建工程竣工圖,台灣省公路總局關渡工程處,民國69年4月17日。
3. 111年第一區養護工程處因應氣候變遷橋梁安全維持計畫-台15線關渡橋檢測、監測及整體安全評估工作-期中報告,交通部公路總局第一區養護工程處,民國112年12月。
4. 台15線關渡橋吊索更換工程-完工報告書,交通部公路總局,民國101年4月。
5. 黃景徽,根據微振訊號並應用等校簡化模型之斜張鋼纜索力分析,國立雲林科技大學,碩士論文,陳建州博士指導,民國98年6月。
6. 陳建州、李政寬、周智傑、張國鎮,斜張鋼纜索力分析之參數研究,中國土木水利工程學刊,第十八捲第四期,民國95年。
7. 林琪恩,簡單平行鋼鉸線模型於纜繩振動檢測之數值研究,國立中興大學,碩士論文,余志鵬博士指導,民國111年9月。
8. 陳建州、吳文華、廖安釗,以鋼纜微振訊號進行鋼纜與橋體之態頻率識別,中國土木水利工程學刊,第二十捲第四期,民國97年。
9. 李晉全,集鹿斜張橋震後修復內應力狀態解析之研究,國立雲林科技大學,碩士論文,陳建州博士指導,民國96年1月。
10. 王鴻諺,橋梁沖刷現地模擬與振動試驗,國立高雄大學,碩士論文,陳振華博士指導,民國100年10月。
11. 王志宏,鋼橋面板箱型鋼梁之疲勞行為,國立高雄第一科技大學,碩士論文,楊國珍博士指導,民國98年2月。
12. 王冠又,以鋼纜微振訊號診斷斜張橋結構健康狀態之研究,國立雲林科技大學,碩士論文,陳建州博士指導,民國96年6月。
13. 台15線關渡橋耐震改善及維修補強工程竣工圖,宸茂營造有限公司,民國110年5月。
14. 謝易儒,更換關渡大橋吊索之研究,國立台灣科技大學,碩士論文,潘誠平博士指導,民國101年7月。
15. 巫文勝,以軸力梁理論提升預力鋼纜傳統評估公式實用性之研究,朝陽科技大學,碩士論文,余志鵬博士指導,民國103年7月。
16. 陳佑嘉,受軸力梁桿件之基本振動特性研究,朝陽科技大學,碩士論文,余志鵬博士指導,民國98年6月。
17. 張國鎮,周智傑,集鹿大橋震害評估與修復之研究,國家地震工程研究中心,民國93年9月。
指導教授 王仲宇(Chung-Yue Wang) 審核日期 2024-1-23
推文 facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu   
網路書籤 Google bookmarks   del.icio.us   hemidemi   myshare   

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明