以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數:4 、訪客IP:100.26.140.179
姓名 陳釧鋒(Shu-Fong Chen) 查詢紙本館藏 畢業系所 機械工程學系 論文名稱 利用網絡模型數值模擬粉末射出成形製程毛細吸附脫脂機制 相關論文 檔案 [Endnote RIS 格式] [Bibtex 格式] [相關文章] [文章引用] [完整記錄] [館藏目錄] [檢視] [下載]
- 本電子論文使用權限為同意立即開放。
- 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
- 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
摘要(中) 粉末射出成形最耗時的製程是將黏結劑從成形後的金屬或是陶瓷胚體內部移除。不僅許多缺陷容易在此製程產生,而且對此製程的認識甚少。為了縮短脫脂時間,可以利用吸附材粉末的毛細吸附作用來移除黏結劑。
本文利用二維的網絡模型,結合有限體積法和蒙地卡羅法數值模擬毛細吸附脫脂機制。數值模擬結果顯示:毛細吸附脫脂的時間與胚體的粉末粒徑成反比,與吸附材的粉末粒徑成正比。此外,胚體的脫脂比例與脫脂時間兩者成二次式關係。我們建議採用較大粒徑比值的胚體與吸附體粉末組合,可有效地縮短毛細吸附脫脂的時間。摘要(英) This study utilizes a two-dimensional network model to investigate the mechanism of wick debinding by the numerical simulation with a technique combining finite-volume and Monte Carlo methods. The results show that wick-debinding time is proportional to the wick powder diameter and inversely proportional to the compact powder diameter. As well as the fractional debinding rate versus wick-debinding time is squared. In order to shorten the wick-debinding time effectively, we suggest that a larger particle size ratio between compact and wick may be employed. 關鍵字(中) ★ 粉末射出成形
★ 毛細吸附脫脂
★ 有限體積法
★ 有限擴散聚集
★ 蒙地卡羅法關鍵字(英) ★ Powder injection molding
★ wick debinding
★ finite-volume scheme
★ diffusion-limited-aggregation(DLA)
★ Monte Carlo method論文目次 目錄
中文摘要 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒Ⅰ
英文摘要 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒Ⅱ
目錄 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒Ⅲ
表目錄 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒Ⅴ
圖目錄 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒Ⅵ
符號說明 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒Ⅷ
第一章 緒論 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒1
1-1 粉末射出成形簡介 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒1
1-2 粉末射出成形的技術問題 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒2
1-2-1 粉末射出成形製程的問題﹒ ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒2
1-2-2 粉末原 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒3
1-2-3 黏結劑 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒4
1-3 本文研究重點 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒4
1-4 文獻回顧 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒9
第二章 理論模式 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒﹒﹒ 10
2-1 基本假設 ﹒﹒﹒ ﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒﹒﹒10
2-2 統御方程式之建立 ﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒﹒11
2-2-1 巨觀上描述毛細吸附脫脂 ﹒ ﹒﹒﹒﹒﹒﹒﹒ ﹒﹒11
2-2-2 微觀上描述毛細吸附脫脂 ﹒﹒ ﹒﹒﹒﹒﹒ ﹒﹒﹒12
2-3 邊界條件 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒13
2-4 孔隙率 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒13
2-5 滲透率 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒14
2-6 毛細壓力 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒15
2-7 無因次參數 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒15
第三章 數值方法 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒17
3-1 網絡模型之建立 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒17
3-2 蒙地卡羅法 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒17
3-3 黏結劑粒子位移決策過程﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒18
3-4 有限體積法 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒18
3-5 數值計算步驟﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒19
第四章 結果與討論 ﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒20
4-1 數值模擬結果之 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒﹒﹒﹒﹒﹒20
4-1-1 毛細吸附脫脂過程的流場分析﹒﹒﹒﹒﹒﹒﹒﹒ ﹒20
4-1-2 無因次分析﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒ ﹒21
4-2 毛細吸附脫脂時間之預測 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒21
4-2-1 胚體的粉末粒徑對脫脂時間的影響﹒﹒﹒﹒﹒ ﹒﹒22
4-2-2 吸附材的粉末粒徑對脫脂時間的影響﹒﹒﹒﹒ ﹒﹒22
4-2-3 胚體的脫脂百分比和脫脂時間的關係﹒﹒ ﹒﹒﹒﹒23
第五章 結論 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒24
參考文獻 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒27
表 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒30
圖 ﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒﹒34參考文獻 1. 楊穆仁,“粉末射出成形技術的近況及展望”, 粉末冶金會刊, 1997, vol. 22, no.2, pp.83~87.
2. 陳文信,“金屬粉末射出成形技術”, 機械工業雜誌, 1996, vol.154, pp.148~158.
3. R.M. German,“Wear Applications Offer Further Growth for PIM”, Metal Powder Report, 1999, June, pp. 24~28.
4. M-J Yang, R. M. German,“Nanophase and Superfine Cemented Carbides Processed by Powder Injection Molding”, Int. J. Refract. Metals & Hard Mater., 1998, vol.16, pp.107~117.
5. C. Toy, Y. Palaci, T. Baykara“A New Thread-guide Composition via Low-pressure Injection Molding”, J. Mater. Proce. Tech., 1995, vol.51, pp.211~222.
6. T. Hartwig, G. Vel, F. petzoldt, H. Kunze, R. Scholl and B. kieback,“Powders for Metal Injection Molding”, J. Europ. Cerma. Soc., 1998, vol.18, pp. 1211~1216.
7. K. F. Hens, T. J. Roche, J. A. Grohowski, “Thermat Sets up for Precision PIM”, Metal Powder Report, 1996, June, pp. 24~28.
8. Karl. F. Hens, “Thermat Expands Precision PIM Operation”, Metal Powder Report, 1998, June, pp. 18~22.
9. R. M. German, K. F. Hens, “Key Issue in Powder Injection Molding”, Ceramic Bulletin, 1991, vol.70, no.8, pp.1294~1302.
10. R.M. German,“Theory of Thermal Debinding”, Int. J. Powder Metall., 1980, vol.23, no.4, pp. 237~245.
11. C. S. Aria, B.R. Petterson, “Influence of Process variables on Debinding by Melt Wicking ”Modern Development in Powder Metallurgy, 1988, vol.18, pp.403~416.
12. B.R. Petterson, C.S.Aria,“Debinding Injection Molded Materials by Melt Wicking”, JOM, 1989, pp.22~24.
13. B.K. Lograsso, R.M. German,“Thermal Debinding of Injection Molded Powder Compacts”, pmi, 1990, vol.2, no.1, pp.17~22.
14. R.Vetter, M.J. Sanders, I. Majewska-Glabus, linZ. Zhuang, Jurek Duszczyk,“Wick-Debinding in Powder injection Molding”, Int. J. Powder Metall., 1994, vol.30, no.1, pp.115~124.
15. R. Vetter, W.R. Brand Horninge, “Squared Root Wick Debinding Model for Powder Injection Moulding”, Powder Metallurgy, 1994, vol. 37, no.4, pp.265~271.
16. 柳立明 ,“ 金屬射出成形中毛細吸附脫脂製程參數之最佳化分析 ”, 國立中央大學機械所碩士論文 , 1999.
17. C.C. Chen, L.W. Hourng,“Numerical Simulation of Two Dimensional Wick Debinding in MIM”, Podwer Metallurgy, 1999, vol.42, no.4, pp.313~319.
18. T. A. Witten, L. M. Sander,“Diffusion-limited-aggreagtion”, Phys. Rev. Lett. , 1981,vol.27, pp.1400~1403.
19. J. O. Hirschfelder, C. F. Curtiss, R. B. Bird,“Molecular Theory of Gases and Liquids”, Wiley, 1954.
20. Carlos A. Grattoni, Richard A. Dawe,“Anisotropy in Pore Structure of Porous Media”, Powder Technology, 1995, vol.85, pp.143~151.
21. Y. Oyama, K. Yamaguchi,“The Distribution of Liquid Content Equilibrium of Powder Bed ”, 1962, Rep. Inst. Phys. Chem. Res., vol.38, pp.392~400.
22. Paul Meakin , “Diffusion-controlled deposition on fibers and surfaces”, The American Physical Society , 1983, vol.31, pp.2616~2623.指導教授 洪勵吾(Lih-Wu Hourng) 審核日期 2000-6-27 推文 facebook plurk twitter funp google live udn HD myshare reddit netvibes friend youpush delicious baidu 網路書籤 Google bookmarks del.icio.us hemidemi myshare