博碩士論文 89323083 詳細資訊




以作者查詢圖書館館藏 以作者查詢臺灣博碩士 以作者查詢全國書目 勘誤回報 、線上人數:18 、訪客IP:52.205.167.104
姓名 謝汎鈞(Fan-Chun Hsieh)  查詢紙本館藏   畢業系所 機械工程學系
論文名稱 鈦合金整流板電化學加工技術研發
(The technical development of Titanium alloy's plate screener using electrochemical machining)
相關論文
★ 迴轉式壓縮機泵浦吐出口閥片厚度對性能影響之研究★ 鬆弛時間與動態接觸角對旋塗不穩定的影響
★ 電化學製作針錐微電極之製程研究與分析★ 蚶線形滑轉板轉子引擎設計與實作
★ 利用視流法分析金屬射出成形脫脂製程中滲透度與毛細壓力之關係★ 應用離心法實驗探求多孔介質飽和度與毛細力之關係
★ 利用網絡模型數值模擬粉末射出成形製程毛細吸附脫脂機制★ 轉注成形充填過程之巨微觀流數值模擬
★ 二維熱流效應對電化學加工反求工具形狀之分析★ 金屬粉末射出成形製程中胚體毛細吸附脫脂之數值模擬與實驗分析
★ 飽和度對金屬射出成形製程中毛細吸附脫脂之影響★ 轉注成型充填過程巨微觀流交界面之數值模擬
★ 轉注成型充填過程中邊界效應之數值模擬★ 射出/壓縮轉注成型充填階段中流場特性之分析
★ 脈衝電化學加工過程中氣泡觀測與分析★ 金屬粉末射出成型二維毛細吸附脫脂及飽和度之研究
檔案 [Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   [檢視]  [下載]
  1. 本電子論文使用權限為同意立即開放。
  2. 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
  3. 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。

摘要(中) 利用電化學加工(ECM)方法製造鈦合金整流板,具有工具無耗損、工件表面無殘留應力等優點,但是如何設計工具形狀及工作參數方可將工件加工成所需之形狀卻是一件不易之工作;往往需不斷測試與修改,進而影響生產時間與效率。
本文將使用套裝軟體FORTRAN來建立一套電腦模式,利用有限差分法計算二維電場之分佈,並利用控制體積觀念來模擬熱流場之變化;以期能準確計算出工件形狀與預測出所需工具形狀。
由於電化學加工過程中,電解液的種類、濃度與溫度均對其導電度有很大的影響,而導電度會影響工件之去除率以及加工精度。故本文也以實驗來量測相同電解液(硝酸鈉)在不同的濃度與溫度下的導電度,亦將所得到的數據代入程式運算,使得數值模擬更準確。
摘要(英) The project presents a numerical for predicting the anode shapes in the electrochemical machining with prescribed tool shape. The conductivity of, and the variation of electrolyte conductivity with temperature had been taken into account in numerical simulation. Results show that the accuracy of the predicted shape is improved.
關鍵字(中) ★ 電化學加工
★ 導電度
★ 鈦合金整流板
★ 硝酸鈉
關鍵字(英) ★ electrochemical machining
★ numerical simulation
論文目次 摘要...........................................Ⅰ
英文摘要.......................................Ⅱ
目錄...........................................Ⅲ
表目錄.........................................Ⅴ
圖目錄.........................................Ⅵ
符號說明.......................................Ⅷ
第一章 緒論....................................1
1-1. 文獻回顧..................................2
1-2. 研究目的..................................4
1-2.1 數值模擬.................................5
1-2.2 實驗部分.................................5
第二章 理論分析................................6
2-1. 電場分佈及加工間隙的變化..................6
2-1.1 電場之決定...............................6
2-1.2 運動關係式...............................7
2-1.3 電流密度與導電度.........................7
2-1.4 加工位置的形成...........................8
2-2. 二維單相熱流場分析........................8
2-2.1 流場之決定...............................8
2-2.2 流場之邊界條件...........................9
2-2.3 溫度場之決定............................10
2-2.4 溫度場之邊界條件........................11
第三章 數值方法...............................12
3-1. 二維橢圓座標系統之轉換...................12
3-2. 二維電場之計算方法.......................17
3-3. 二維流場之計算方法.......................17
3-4. 二維單相流場數值計算流程.................20
3-5 完整的計算流程流..........................21
第四章 結果與討論.............................22
第五章 結論...................................26
第六章 參考文獻...............................27
參考文獻 l.佐藤敏一著,賴耿陽譯著, "金屬腐蝕加工技術", 復漢出版杜 (1986)
2.木本康雄著,耿陽譯著, ”精密加工之電學應用", 復漢出版社 (1982)
3. A. H. Meleka & D. A. Glew, “Electrochemical Machining", Review 221, Internal Meta1s Review, pp. 229-252 (1977)
4. J. F. Thorpe and R. D. Zerkle, “Theroretical Analysis of the Equilibrium Sinking of Shallow, Axially Symmetric, Cavities by Elctrochemical Machining", Elctrochemical Soc, pp. 1-39 (1971)
5. A. L. Klylov, Soviet Phys. Doklady, Vol. l3, pp. 15 (1968)
6. J. A. McGeough, “Princiiples of Electrochemical Machining", Chapman & Hall, London (1974)
7. V. K. Jain and C. Pandey, “Tooling Design for ECM", Precision Engineering, pp. 195-206 (1980)
8. D. E. Colletc, R. C. Hewson Browne and D. W. Windle, "A Complex Variable Approach to Electrochemical Machining Problems", Journal of Engineering Mach., Vo1. 4, pp. 29-37 (1970)
9. R. C. Hewson Browne, “Further Applications of Complex Variable Methods to Electrochemical Machining Problems”, Journal of Engineering Math., Vol. 5, pp. 233-240 (1971)
l0. R. V. Churchill, J. W. Brown and R. F. Verhey, “Complex Variables and Applications", McGrawill Book Co., New York (1974)
11. O.H. Narayanan, S.Hinduja and C. Noble, “The Prediction of Workpiece Shape During Electrochemical Machining by The Boundary Element Method", Int. J. Mach. Tool Des. Res., Vol. 26, 3, pp. 323-338 (1980)
12. C.A. Brebbia, “The Boundary Element Method for Engineers", Pentech Press (1980)
13. V. K. Jain, P. G. Yogindra and S.Murugan, “Prediction of Anode Profile in ECBD and ECD Operations.”, Int. J. Mach. Tools Manufact., Vol. 27, 1, pp. 113-114 (1987)
14. 陳志誠, “電化學加工刀具之設計”, 國立中央大學機械研究所碩士論文 (1990)
15 L.W. Hourng and C.S. Chang, ”Numericd Calculation of Electrochemical Drillling", Int. J. 0f applied Electrochemistry, Vol. 23, pp. 316-32l (1993)
16. L. W. Hourng, and C. S. Chang, “Numerical Simulation of Two dimension Fluid Flow Electrochemical Drilling”, J. 0f applied Electrochemistry, Vol. 24, pp. 1170-1175 (1994)
17. R. Hunt, ”The Numerical Solution of Ellipitic Free Boundary Problems Using Multigrid Techniques", Comp. Phys., Vol. 65, pp. 448-461 (1986)
18. R. Hunt, "An Embedding Method for the Numerical Solution of the Cathod Design Problem in Electrochemical Machining", International Journal for Numerical Methods in Engineering, Vol. 29, pp. l177-1192 (1990)
19. Shuvra Das and Amb K.Mitra “Use of Boundary Element Method for the Determination of Tool Shape in Electrochemical Machining, International Journal for Numerical Methods in Engineering, Vol. 35, pp. 1045-1054 (1992)
20.蔡和蒼, "反求法在電化學加工刀具設計上之應用", 國立中央大學機械研究所碩士論文(1995)
2I. H. Tipton, "Dynamics of Electrochemical Machining Proc." 5th Intern. Conf. Mach Too1 Res., Birmingham, England, Sept., pp. 509-522 (1964)
22.K. Kawafune, T. Mikoshiba, K. Noto and K. Hirata, "Accurary in Cavity Sinking by ECM", Annals of CIRP, Vol. 15, pp. 65/1-65/13. (1967)
23. J. F. Thorpe and R. D. Zerkle, "An Analytical Basis for Investigating the Dynamics of Electrochemical Machining", Report UCME-318-1, Mechanical Engineering Dept. University of Cincinnati, Ohio, December, (1967)
24. J. F. Thorp, "On the Kinematics of Electrochemical Machining", ASME Winter Annu Meeting, New York, Dec. (1968)
25.J. F. Thorpe and R. D. Zerkle, "Analytic Determination of the Equilibrium Electrode Gap in Electrochemical Machining", Int. Jour. Mach. Tool. Des. And Res., Vol. 9, pp.131-144 (1969)
26. 陳川吉, "電化學加工過程熱流現象之分析", 國立中央大學機械研究所碩士論文 (1990)
27. C. S. Chang, L. W. Hourng and C.T. Chung, “Tool Design in Electrochemistry considering the Effect of Thermal-fluid Properties,” J. Applied Electrochemistry, Vol. 29, pp. 321-330 (1999)
28. C. S. Chang and L. W. Hourng, “Two dimensional Two-phase Numerical Model for Too1 Design in Electrochemical Machining”, J. Applied Electrochemistry, in print
29. D. K. Cheng, “Field and Wave Electromagnetics", Addison- Wesley Publishing Company Inc. (1983)
30. J. F. Thompson, Z. U. A. Warsi, and C. W. Mastin, “Numerical Grid Generation Foundations and Applications”, North-Holland Pub. , New York, (1985)
31. 黃進光, “三維橢圓座標之流場格點分析”, 國立中央大學機械研究所碩士論文(1987)
32. J. F. Thompson, F. C. Thames and C. W. Mastin, “TOMCATA code for Numerical Generation of Boundary Fitted Curvilinear Coordinate System on Field Containing Any Number of Arbitrary 2-D bodies”, Journal of Computational Physics, Vol. 24, pp. 274-302. (1977)
33. M. Visbal and D. Knight, “Generation of Orthogonal and Nearly Orthogonal Coordinates with Grid Control Near Boundaries”, AIAA Journal, Vol. 20, No. 3, pp. 306-325, (1982)
34. L. W. Hourng and C. K. Hwang, “Computational Among Grid Generation Using Elliptic Partial Differential Equations”, Journal of the Chinese Society of Mechanical Engineers, Vol. 10, No. 5, pp. 383-392 (1988)
指導教授 洪勵吾(Lih-Wu Hourng) 審核日期 2002-7-5
推文 facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu   
網路書籤 Google bookmarks   del.icio.us   hemidemi   myshare   

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明