博碩士論文 90521045 詳細資訊




以作者查詢圖書館館藏 以作者查詢臺灣博碩士 以作者查詢全國書目 勘誤回報 、線上人數:8 、訪客IP:54.81.220.239
姓名 賈國揚(Kuo-Yang Chia)  查詢紙本館藏   畢業系所 電機工程學系
論文名稱 大面積矽偵測器的製程改良與元件設計
(Studies of Process Improvement and Device Design for Large-Area Silicon Detector)
相關論文
★ 金屬-半導體-金屬光偵測器的特性★ 非晶質氮化矽氫基薄膜發光二極體與有機發光二極體的光電特性
★ 具非晶質n-i-p-n層之氧化多孔矽發光二極體的光電特性★ 低漏電流與高崩潰電壓大面積矽偵測器製程之研究
★ 具自行對準凹陷電極1x4矽質金屬-半導體-金屬光偵測器陣列的特性★ 非晶矽射極異質雙載子電晶體與有機發光二極體的特性
★ 吸光區累崩區分離的累崩光二極體★ 蕭特基源/汲極接觸的反堆疊型非晶質矽化鍺薄膜電晶體
★ 矽晶圓上具有隔離氧化層非晶質薄膜發光二極體之光電特性★ 具非晶異質接面及溝渠式電極之矽質金屬-半導體-金屬光偵測器的暗電流特性
★ 非晶矽/晶質矽異質接面矽基金屬-半導體-金屬光檢測器與具非晶質無機電子/電洞注入層高分子發光二極體之研究★ 具非晶質矽合金類量子井極薄障層之高靈敏度平面矽基金屬–半導體–金屬光檢測器
★ 具蕭特基源/汲極的上閘極型非晶矽鍺與 多晶矽薄膜電晶體★ 具組成梯度能隙非晶質矽合金電子注入層與電洞緩衝層的高分子發光二極體
★ 非晶質吸光區與累增區分離之類超晶格累崩光二極體★ 具非晶質矽合金調變週期類超晶格薄膜複層之低暗電流高熱穩定度平面矽基金屬–半導體–金屬光檢測器
檔案 [Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   [檢視]  [下載]
  1. 本電子論文使用權限為同意立即開放。
  2. 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
  3. 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。

摘要(中) 本論文的主要目的是希望能藉由製程條件的改善與元件結構的改良提昇大面積矽偵測器的特性。為了降低漏電流及提高崩潰電壓,本論文探討偵測器的背面製程對元件特性的影響,並且證實利用磷摻雜的多晶矽外質去疵技術可以減少元件內部的缺陷,使元件特性獲得明顯的改善。
另外,在元件結構方面也藉由模擬軟體與實驗測試鍵(test-key)結果的協助,獲得最佳的相關元件構造參數,這些參數包括合適的氧化層厚度、接面深度、正面電極延伸長度及防護圈的配置等等。
摘要(英) In order to obtain a large-area silicon detector with good performances, such as low leakage current, high breakdown voltage and high reliability, the process improvement and structure design for a large-area silicon strip detector had been studied in this thesis.
Firstly, an overview including fundamental considerations, operation principles, and basic processing has been given, and accordingly the required structure and performance of the detector were summarized. Then a lot of methods to reduce leakage current and furthermore increase breakdown voltage of the device by means of optimized structure and improved processing were presented. With the measured results of test-keys, the simulated device structure had been verified to have the good performances.
A single-sided silicon strip detector with area of 1.12 cm2 and having an average leakage current reduced from 410 down to about 210 nA per diode strip after employing a backside phosphor-doped polysilicon gettering process at 985 ℃ had been obtained. So, it is possible to minimize the device leakage current with the well-developed gettering process.
The experimental results of test-keys not only verified the simulation data but also provided the guidelines to obtain an optimum device structure with specified length of field-plate, spacing between two strips, and lateral radius of curvature of the strip corners.
關鍵字(中) ★ 最佳化
★ 高電壓
★ 粒子偵測器
★ 矽偵測器
★ 防護圈
★ 低漏電流
關鍵字(英) ★ leakage current
★ breakdown voltage
★ strip
★ field plate
★ guard ring
★ optimal
★ silicon detector
論文目次 Abstract Ⅲ
Table Captions Ⅳ
Figure Captions Ⅴ
Chapter 1 INTRODUCTION 1
Chapter 2 FUNDAMETAL CONSIDERATIONS AND FABRICATION PROCESSES 6
2.1 Fundamental Considerations……………………………………6
2.1.1 Material…………………………………………………………6
2.1.2 Structures………………………………………………………8
2.1.3 Noise……………………………………………………………11
2.2 Device Design……………………………………………………12
2.3 Conventional Fabrication Processes……… ………………13
Chapter 3 DEVICE PROCESS AND STRUCTURE DESIGN to IMPROVE PERFORMANCE 22
3.1 Process Improvements…………………………………………22
3.1.1 Backside process……………………………………………22
3.1.2 Thermal budget………………………………………………24
3.1.3 Gettering techniques………………………………………24
3.1.4 Metallization………………………………………………26
3.1.5 Contact area…………………………………………………26
3.2 Device Design…………………………………………………27
3.2.1 Field-plate…………………………………………………27
3.2.2 Guard-ring arrangement……………………………………30
3.2.3 Combination of field-plate and guard-ring effect…31
3.3 Summaries………………………………………………………31
Chapter 4 TEST-KEYS 50
4.1 Gated Diodes…………………………………………………50
4.2 Field-Plate………………………………………………… 52
4.3 Multiple Guard-Rings………………………………………52
4.4 Corner Effect…………………………………………………53
4.5 Summaries………………………………………………………54
Chapter 5 CONCLUSION 62
REFERENCES 63
參考文獻 [1]A. H. Walenta,“Principles and New Development of Semiconductor Radiation Detectors”, Nuclear Instruments and Methods in Physics Research A253, pp.558-571, 1987.
[2]A. C. Melissinos, “Experiments in Modern Physics”, Academic Press, Inc., New York, USA, 1989.
[3]G. F. Knoll, “Radiation Detection and Measurement”, 2nd ed., John Wiley & Sons, Inc., New York, USA, 1989.
[4]S. M. Sze, “Semiconductor Sensors”, John Wiley & Sons, Inc., New York, USA, 1994.
[5]E. Gatti and P. Rehak, “Semiconductor Drift Chamber - an Application of a Novel Charge Transport Scheme”, IEEE Trans. on Electron Devices, ED-29, p.1388, 1982; also Proc. 2nd Pisa Meeting on Advanced Detectors, Grosseto, Italy, in Nuclear Instruments and Methods in Physics Research 225, pp.608-614, 1984.
[6]E. Gatti, P. Rehak, and J. T. Walton, “Silicon Drift Chamber First Results and Optimum Processing of Signals”, Nuclear Instruments and Methods in Physics Research 226, pp.129-141, 1984.
[7]L. Struder, G. Lutz, M. Sterzik, P. Holl, J. Kemmer, U. Prechtel, T. Ziemann and P. Rehak “First Tests with Fully Depleted pn-CCD's”, IEEE Trans. On Nuclear Science, Vol. 35, No. 1, pp. 372-376, 1988
[8]V. Radeka, P. Rehak, S. Rescia, E. Gatti, A. Longoni, M. Sampietro, G. Bertuccio, P. Holl, L. Struder, and J. Kemmer, “Implanted Silicon JFET on Completely Depleted High-Resistivity Devices”, IEEE Electron Device Letters, Vol. 10, No.2, pp.91-93, 1989.
[9]J. Kemmer and G. Lutz, “New Structures for Position Sensitive Semiconductor Detectors”, Nuclear Instruments and Methods in Physics Research A273, pp.588-598, 1988.
[10]H. Becker, T.Boulos, P. Cattaneo, H. Dietl, D. Hauff, E. Lange, G. Lutz, H. G. Meser, A.S. Schwartz, R. Settles, L. Struder, J. Kemmrr, U. Prechtel, T. Ziemann, and W. Buttler, “New Developments in Double Sided Strip Detectors”, IEEE Trans. On Nuclear Science, Vol. 37, No. 4, pp.101-106, 1990.
[11]Alvsvaag, S.J.; Maeland, O.A.; Klovning, A.; Benvenuti, A.C.; Giordano, T.; Guerzoni, M.; Navarria, F.L.; Verardi, M.G.; Camporesi, T.; Vallazza, E.; Bozzo, M.; Cereseto, R.; Barreira, G.; Espirito Santo, M.C.; Maio, A.; Onofre, A.; Peralta, L.; Pimenta, “A Silicon Pad Shower Maximum Detector for a "Shashlik" Calorimeter “IEEE Trans. On Nuclear Science, Vol.42, No.4, pp. 469-473, 1995.
[12]Avrillon, S.; Ikeda, H.; Matsuda, T.; Asano, Y.; Tsuchiya, S.; Saitoh, Y.; Inoue, M.; Yamanaka, J. “Performance of a pMOS Pixel To Be Used in Radiation Detectors “, IEEE Trans. On Nuclear Science, Vol.43, No.3, pp. 1161-1164, 1996.
[13]Passeri, D.; Ciampolini, P.; Baroncini, M.; Santocchia, A.; Bilei, G.M.; Checcucci, B.; Fiandrini, E, “Comprehensive Modeling of Silicon Microstrip Detectors “, IEEE Trans. On Nuclear Science, Vol.44, No.3, pp. 598-605, 1997.
[14]G. Batignani, L. Bosisio, A. Conti, E. Focardi, F. Forti, M. A. Giorgi, M. Grandi, G. Parrini, P. Tempesta, G. Tonelli, and G. Triggiani, “Test Results on Double-Side Readout Silicon Strip Detectors”, IEEE Trans. On Nuclear Science, Vol.36, No. 1, pp. 40-45, 1989.
[15]Saitoh, Y.; Akamine, T.; Inoue, M.; Yamanaka, J.; Kadoi, K.; Takano, R.; Kojima, Y.; Miyahara, S.; Kamiya, M.; Ikeda, H.; Matsuda, T.; Tsuboyama, T.; Ozaki, H.; Tanaka, M.; Iwasaki, H.; Haba, J.; Higashi, Y.; Yamada, Y.; Okuno, S.; Avrillon, S.; Nemoto, T, ” Fabrication of a Double-Sided Silicon Microstrip Detector with an ONO Capacitor Dielectric Film”, IEEE Trans. On Nuclear Science, Vol.43, No.3 pp. 1123-1129, 1996.
[16]Iwata, Y.; Ohsugi, T.; Fujita, K.; Kitabayashi, H.; Yamamoto, K.; Yamamura, K.; Unno, Y.; Kondo, T.; Terada, S.; Kohriki, T.; Asai, M.; Nakano, I.; Takashima, R., “Optimal p-Stop Pattern for the N-side Strip Isolation of Silicon Microstrip Detectors”, IEEE Trans. On Nuclear Science, Vol.45, No.3, pp. 303-309, 1998.
[17]Saitoh, Y.; Akamine, T.; Inoue, M.; Yamanaka, J.; Echigo, N.; Miyahara, S.; Kamiya, M.; Ikeda, H.; Matsuda, T.; Bozek, A.; Haba, J.; Koike, S.; Ozaki, H.; Tanaka, M.; Iwasaki, H.; Higashi, Y.; Tsuboyama, T.; Yamada, Y.; Banas, E.; Natkaniec, Z.; Palka, H., “ Performance of A Double-Sided Silicon Microstrip Detector with a Wide-Pitch N-side Readout Using a Field-Plate and A Multi P-stop structure“, Conference Record of IEEE 1996 Nuclear Science Symposium Conference, Vol. 1, No. 3, pp. 181 -185, 1996.
[18]Tsuboyama, T.; Haba, J.; Ikeda, H.; Iwasaki, H.; Matsuda, T.; Ozaki, H.; Tanaka, M.; Yamada, Y.; Saito, Y.; Akamine, K.; Inoue, M.; Yamanaka, J.; Kadoi, K.; Takano, R.; Kojima, Y.; Miyahara, S.; Kamiya, M.; Okuno, S.; Avrillon, S.; Hazumi, M.; Nagashima, “Test of A Double-Sided Double-Metal Silicon Microstrip Detector with An ONO Insulator, “Conference Record of IEEE 1995 Nuclear Science Symposium and Medical Imaging Conference Vol. 1 , pp. 192 –195,1995.
[19]Alexander, J.P.; Bebek, C.J.; Browder, T.E.; Dobbins, J.A.; Gray, S.G.; Honscheid, K.; Jones, C.D.; Katayama, N.; Katris, J.S.; Kim, P.C.; Selen, M.; Worden, H.M.; Wurthwein, F.; Gronberg, J.; Morrison, R.J.; Hale, D.L.; Korte, C.; Kyre, S.; Nelson, H.N.; “Studies of Double-Sided, Double-Metal Silicon Microstrip Detectors”, Conference Record of IEEE 1992 Nuclear Science Symposium and Medical Imaging Conference Vol. 1, pp. 224 -226, 1992
[20]The Website of CMS outreach http://cmsinfo.cern.ch/Welcome.html/CMSmedia/CMSphotos/index.html
[21]Warner Ten Kate, “The Silicon Microstrip Detector”. (a copy of transparencies)
[22]B. Hyams, U. Koetz, E. Belau, R. Klanner, G. Lutz, E. Neugebauer, A. Wylie and J. Kemmcr, “A Silicon Counter Telescope to Study Short-lived Particles in High-energy Hadronic Interactions”, Nuclear Instruments and Methods in Physics Research 205, pp.99-105, 1983.
[23]S. M. Sze, “Physics of Semiconductor Devices”, John Wiley & Sons, Inc., New York, USA, 1981.
[24]M. Campanella,N. Croitoru, F. Groppi, F. Lemeilleur, S. Pensotti, P. G. Rancoita, and A. Seidman, “The Effect of Radiation on Ion-Implanted Silicon Detectors”, Nuclear Instruments and Methods in Physics Research A243, pp.93-97, 1986.
[25]G. Batignani, L. Bosiso, E. Forcardi, F. Forti, M. A. Giorgi, L. Moneta, G. Parrini, G. Tonelli, and G. Triggiani, “Development and Performance of Double Sided Silicon Strip Detecrors”, Nuclear Instruments and Methods in Physics Research A310, pp.160-164. 1991.
[26]P. Hell, J. Kemrner, U. Prrchtel, T. Ziemann, D. Hauff, G. Lutz, A. S. Schwarz, and L. Struder, “A Double-Sided Silicon Strip Detector with Capacitive Readout and a New Method of Integrated Bias Coupling”, IEEE Trans. On Nuclear Science, Vol. 36, No.1, pp.251-255, 1989.
[27]W. T. Lin, Y. H. Chang, A. E. Chen, K. T. Huang, and W. C. Tsay, “PHOSBOS Silicon Sensor Production at NCU”, PHOROS project review of quarter 2, National Brookhaven Laboratory, June 18, 1997.
[28]B. J. Baliga, “ Modern Power Devices”, John Wiley & Sons, Inc., New York, USA, 1987.
[29]Wen-Chin Tsay; Jyh-Wong Hong; Chen, A.; Lin, W.T.; Hsien-Ten Ting; Song-Tsang Chiang; Ching-Lan Yen, “ONO SMD - A Silicon Microstrip Detector with ONO A-C Coupled Capacitor”, Electron Devices and Materials Symposium, EDMS, pp. 6-8-29 -6-8-32 , 1994.
[30]Wen-Chin Tsay, Jyh-Wong Hong, Y.H.Chang, A.Chen, S.R.Hou, S.L.Hsu, C.H.Lin, Willis T.Lin, Hsien-Jen Ting, Song-Tsang Chiang, Emily Chuang, and Su-Wen Hwang, “Studies of Large- Area Silicon Microstrip Sensors”, IEEE Trans. On Nuclear Science, Vol.42, No.4, pp. 437-440, 1995.
[31]A. Rohatgi and P. Rai-Choudhury, “Design, Fabrication and Analysis of 17-18 Percent Efficient Surface Passivated Silicon Solar Cells,” IEEE Trans. Electron. Devices, Vol. ED-31, pp. 596-600, 1984
[32]P. Bloch, A. Cheremukhin, S.Golubkov, I. Golvutvin, N. Egorov, K. Konjkov, A. Peisert, A. Sidorov, and N. Zamiatin, “Investigation of Silicon Sensor Quality as a Function of the Ohmic Side Processing Technology,” IEEE Trans. Nuclear Science, Vol. 49, No.1, pp. 321-324, 2002
[33]G. F. Dalla Betta, M. Boscardin, G. Verzellesi, G. U. Pignatel, A. Fazzi, and G. Soncini, “A Test Chip for the Development of PIN-Type Silicon Radiation Detectors,” IEEE Porceedings on Microelectronic Test Structures, Vol. 9, pp. 231-232, 1996
[34]R. A. Craven and H. W. Korb, “Internal Gettering in Silicon,” Solid State Technology, pp.55-61, July, 1981.
[35]Chun-Yen Chang and C. T. Sune, “An Analytic Approach for Optimal Field Ring Spacing of a Diode Under Punchthrough Operation,” IEEE Electron Device Letters, Vol. EDL-7, No. 1, pp. 35-37, Jan, 1986.
[36]V. Boisson, M. Le Helley, and J. P. Chante, “Analytical Expression for the Potential of Guard Rings of Diodes Operating in the Punchthrough Mode,” IEEE Trans. on Electron Devices, Vol. ED-32, No. 4, pp. 838-841, April, 1985
[37]C. Basavanagoud and K. N. Bhat, “Effect of Lateral Curvature on the Breakdown Voltage of Planar Diodes,” IEEE Electron Deviec Letters, Vol. EDL-6, pp.276-278, 1985
[38]Il-Jung Kim, Seong-Dong Kim, Yearn-Ik Choi, and Min-Koo Han, “Analytical Expressions for the Three-Dimensional Effect on the Breakdown Voltage of Planar Junctions in Nonpunchthrough and Punchthrough Case,” IEEE Trans. on Eleetron Devices, Vol.41, No.9, pp.1661-1665, 1994
指導教授 洪志旺(Jyh-Wong Hong) 審核日期 2003-7-7
推文 facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu   
網路書籤 Google bookmarks   del.icio.us   hemidemi   myshare   

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明