 |
|
|
|
以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數：15 、訪客IP：3.145.125.190
姓名 賴義吉(Yi-Chi Lai) 查詢紙本館藏 畢業系所 機械工程學系 論文名稱 水對水在不同板片型式之板式熱交換器性能測試分析與比較 相關論文 檔案 [Endnote RIS 格式]
[相關文章]
[文章引用]
[完整記錄]
[館藏目錄]
至系統瀏覽論文 ( 永不開放)
摘要(中) 本研究將針對水對水在凸出凹入型與山型紋板面型式之板式熱交換器的熱傳及壓降性能，進行實驗分析，並提出預測板式熱交換器熱傳及壓降性能之半經驗關係式比較。測試板片型式分別為凸出凹入型與山型紋板片。山型紋板片幾何參數，傾斜角越大，流體越容易轉變成紊流，使得熱傳量與壓降皆增加。
凸出凹入型板片雖然也是使流體在低流速下轉變為紊流，使得熱傳增加。但效果卻沒有山型紋板片佳。壓降方面，凸出凹入型板片之摩擦因子比山型紋小但隨雷諾數變化較大。凸出凹入型板片熱交換器比山型紋板片熱交換器密集，對空間上有限制時，凸出凹入型板片之熱交換器是可以考慮使用的。關鍵字(中) ★ 熱傳
★ 壓降
★ 凸出凹入型板片
★ 山型紋板片
★ 板式熱交換器關鍵字(英) 論文目次 摘要----------------------------------------------------------------------------------- i
目錄----------------------------------------------------------------------------------- ii
表目錄------------------------------------------------------------------------------- iv
圖目錄------------------------------------------------------------------------------- v
符號說明-------------------------------------------------------------------------- viii
第一章 前言------------------------------------------------------------------------ 1
研究背景---------------------------------------------------------------------------- 1
研究目的---------------------------------------------------------------------------- 2
第二章 文獻回顧------------------------------------------------------------------ 4
2.1凸出凹入型式------------------------------------------------------------------ 5
2.2山型紋型式--------------------------------------------------------------------- 6
2.2.1山型紋傾斜角的影響------------------------------------------------- 6
2.2.2山型紋板片波紋振幅與節距對性能的影響-------------------- 10
第三章 實驗方法----------------------------------------------------------------- 23
3.1 實驗系統---------------------------------------------------------------------- 23
3.1.1測試段----------------------------------------------------------------- 23
3.1.2熱水側循環系統----------------------------------------------------- 24
3.1.3冷水側循環系統----------------------------------------------------- 24
3.2 實驗量測設備---------------------------------------------------------------- 24
3.2.1 溫度測量-------------------------------------------------------------- 24
3.2.2 壓力測量-------------------------------------------------------------- 25
3.2.3 壓差測量------------------------------------------------------------- 25
3.2.4 流量測量------------------------------------------------------------- 25
3.2.5 資料擷取系統------------------------------------------------------- 26
3.3 實驗步驟--------------------------------------------------------------------- 26
3.4 數據換算--------------------------------------------------------------------- 27
第四章 實驗結果與討論------------------------------------------------------- 49
4.1 壓降性能--------------------------------------------------------------------- 49
4.2 熱傳性能--------------------------------------------------------------------- 51
第五章 結論---------------------------------------------------------------------- 68
參考文獻-------------------------------------------------------------------------- 69
附錄-------------------------------------------------------------------------------- 72參考文獻 Abdel-Kariem, A. H., Fletcher, L. S., 1999, “A Comparative Analysis of Heat Transfer and Pressure Drop in Plate Heat Exchangers,” 5th ASME/JSME Joint Thermal Engineering Conference Proceedings, Paper No. AJTE99 - 6291.
Bond, M. P., 1981, “Plate Heat Exchangers for Effective Heat Transfer,” The Chemical Engineer, April.pp. 162－167.
Ding, J., and Manglik, R. M., 1996, “Analytical Solutions for Laminar Fully Developed Flows in Double-Sine Shaped Ducts, ” Heat and Mass Transfer, Vol. 31, pp. 269 - 277.
Focke, W. W., and Knibble, P. G., 1984, Flow Visualization in Parallel Plate Ducts with Corrugated Walls,” CSIR Report CENC M-519.
Focke, W. W., Zachariades, J., and Oliver, I., 1985, “The Effect of Corrugation Onclination Angle on the Thermohydraulic Performance of Plate Heat Exchangers,” International Journal of Heat and Mass transfer, Vol. 28, pp. 1469 - 1479.
Heavner, R. L., Kumar, H., and Wanniarachchi A. S., 1993, “Effect of Chevron Angle,” AIChE Symposium Series, Heat Transfer Atlanta, Vol. 89, No.295, pp. 262 - 267.
Kays, W. M., and London, A. L., 1984, Compact Heat Exchangers, 3rd Edition, pp. 108-114, McGraw-Hill, New York.
Lee, K. S., Kim, W. S., and Si, J. M., 2000, “Optimal shape and arrangement of staggered pins in the channel of a plate heat exchanger,” International Journal of Heat and Mass transfer, Vol. 44, pp. 3223 - 3231.
Matsushima, H., and Uchida, M., 2002, “Evaporation Performance of a Plate Heat Exchanger Embossed with Pyramid-Like Structures,” Journal of Enhanced Heat Transfer, Vol. 9, pp. 171 - 179.
Muley, A., and Manglik, R. M., 1999a, “Experimental Study of Turbulent Flow Heat Transfer and Pressure Drop in a Plate Heat Exchanger With Chevron Plates,” ASME Journal of Heat Transfer, Vol. 121, pp. 110 - 117.
Muley, A., Manglik, R. M., and Metwally, H. M., 1999b, “Enhanced Heat Transfer Characteristics of Viscous Liquid Flows in A Chevron Plate Heat Exchanger,” ASME Journal of Heat Transfer, Vol. 121, pp. 1011 - 1017.
Smith, C. V., and Troupe, R. A., 1965, “Pressure Drop Studies in Plate Heat Exchanger,” AIChE Journal, Vol. 11, No. 3, pp. 487 - 497
Sung, H. Lee, Young, I. Cho, Cheolho, Bai, and Daniel, J. Cho, 2000, “The Effect of Aspect Ratio on Turbulent Flow Heat Transfer and Pressure Drop in a Plate Heat Exchanger,” International Journal of Heat Exchangers, Vol. 1, pp. 113 - 124.
王啟川，2001，熱交換器設計，五南圖書出版公司，台北。
黃慶初，張永鵬，黃錦文，楊秉純,2000“以潤滑油為工作流體對板式熱交換器影響之分析“，技術學刊，第13卷，第2期，第229-236頁。
蔡益瑞，張永鵬，黃錦文，張庭瑞,2000“板片波紋結構對板使熱交換器性能之實驗分析“，技術學刊，第15卷，第2期，第223-230頁。
林佩芝，1995，幾何參數對板式熱交換器性能之影響，國立交通大學機械工程研究所碩士論文。
翁嘉鴻，2002，水對水板式熱交換器性能測試分析，國立中央大學機械工程研究所碩士論文。指導教授 楊建裕(Chien-Yuh Yang) 審核日期 2004-7-19 推文 plurk
funp
live
udn
HD
myshare
netvibes
friend
youpush
delicious
baidu
網路書籤 Google bookmarks
del.icio.us
hemidemi
facebook
twitter
google
reddit