以脈衝直流磁控濺鍍法製作含氫非晶矽薄膜於太陽電池之應用

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：47

、訪客IP：3.145.154.219

姓名

蘇韋寧(Wei-ning Su) 查詢紙本館藏

畢業系所

光電科學與工程學系

論文名稱

以脈衝直流磁控濺鍍法製作含氫非晶矽薄膜於太陽電池之應用
(Fabrication of Hydrogenated Amorphous Silicon Thin Films Using DC-pulse Magnetron Sputtering)

相關論文

★ 半導體雷射控制頻率	★ 比較全反射受挫法與反射式干涉光譜法在生物感測上之應用
★ 193nm深紫外光學薄膜之研究	★ 超晶格結構之硬膜研究
★ 交錯傾斜微結構薄膜在深紫外光區之研究	★ 膜堆光學導納量測儀
★ 紅外光學薄膜之研究	★ 成對表面電漿波生物感知器應用在去氧核糖核酸及微型核糖核酸雜交反應檢測
★ 成對表面電漿波生物感測器之研究及其在生醫上的應用	★ 探討硫化鎘緩衝層之離子擴散處理對CIGS薄膜元件效率影響
★ 以反應性射頻磁控濺鍍搭配HMDSO電漿聚合鍍製氧化矽摻碳薄膜阻障層之研究	★ 掃描式白光干涉儀應用在量測薄膜之光學常數
★ 量子點窄帶濾光片	★ 以量測反射係術探測光學薄膜之特性
★ 嵌入式繼光鏡顯微超頻譜影像系統應用在口腔癌切片及活體之設計及研究	★ 軟性電子阻水氣膜之有機層組成研究

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

近年來，由於能源危機的問題，薄膜式太陽電池的研究引起很多專家學者的注意。目前最普遍為民生所使用的太陽電池是由電漿輔助化學氣相沉積法(plasma-enhance chemical vapor deposition, PECVD)所製作出的非晶矽薄膜太陽電池，但是PECVD在製程上需要昂貴的設備費及使用有毒、易燃氣體矽烷(silane, SiH4)，因此本研究主旨在探討使用脈衝直流磁控濺鍍製作含氫非晶矽薄膜應用於薄膜式太陽電池的研究。利用調變不同製程溫度、脈衝頻率與氫氣通量，製作出含氫非晶矽薄膜(a-Si:H)，並量測其特性。將實驗所製作出的薄膜量測XRD、FTIR、導電率，得到薄膜的結構、矽氫鍵結、導電率的結果，作分析與比較。
於實驗中發現，以脈衝儀直流磁控濺鍍系統所製作出的非晶矽薄膜，隨著氫氣通量的增加薄膜的R* (Microstructure factor)會增加，且在溫度由250℃升至350℃對於Si-H2鍵結比例無明顯影響，在氫氣通量8sccm以上，薄膜結構會趨向結晶。電性部分隨著氫氣量的增加，有照光與無照光的導電率都會上升，但是無照光的上升幅度比較大，造成photosensitivity下降，而非晶矽薄膜部分，photosensitivity有大多數皆超過103或104以上，可見此薄膜對於光照之後會有光起電效應作用，可應用於薄膜太陽電池的非晶純矽層(intrinsic layer, i-layer)。

摘要(英)

In recent years, the researches of Thin Film Solar Cells attracted much attention for the reason of the energy crisis. To fabricate amorphous silicon thin film solar cells using plasma-enhance chemical vapor deposition (PECVD) is the most popular method. The disadvantages of PECVD are the high facility cost and using the toxic processing gases such as silane (SiH4). In this research, the hydrogenated amorphous silicon (a-Si:H) thin films for the application of thin thing film solar cell were fabricated using DC pulse magnetron sputtering with the different process temperatures, the DC pulse frequencies or the hydrogen gas flows and measured by using XRD,FTIR, conductivity measurement.
The results show that the microstructure factors(R*) of a-Si:H were increased when the hydrogen gas flow increased. And the concentration of Si-H2 bonds is not obviously change at high temperature (TS=350℃) or temperature (TS=250℃). According to the analysis of XRD, the a-Si:H films tend to crystallize when the hydrogen gas flow increased. Besides, the analyses of the electrical property show the dark and photo conductivity were increased and photosensitivities decreased when the hydrogen gas flow increased at all temperatures and pulse frequencies. Finally, the photosensitivities of the a-Si:H thin films are all higher than 103 or 104 which means that the a-Si:H thin films fabricated using DC pulse magnetron sputtering can be applied to the intrinsic layer of thin film solar cell.

關鍵字(中)

★ 薄膜
★ 濺鍍
★ 薄膜太陽電池
★ 非晶矽

關鍵字(英)

★ amorphous silicon
★ thin film
★ solar cell

論文目次

第一章緒論 - 1 -
1-1前言 - 1 -
1-2動機 - 3 -
第二章文獻回顧與基本理論 - 4 -
2-1 太陽電池簡介 - 4 -
2-1-1 太陽電池的發展[8] - 4 -
2-1-2 光電轉換原理 - 6 -
2-1-3 太陽電池的能源轉換效率[9] - 8 -
2-2 非晶矽薄膜太陽電池 - 10 -
2-2-1 非晶矽薄膜太陽電池發展歷史 - 10 -
2-2-2 光劣化效應 - 12 -
2-2-3 非晶矽薄膜中矽氫原子鍵結 - 13 -
2-3 濺鍍原理 - 15 -
2-3-1 電漿原理 - 15 -
2-3-2 脈衝直流磁控濺鍍原理[17] - 17 -
第三章實驗儀器與內容 - 21 -
3-1 鍍製儀器-脈衝直流磁控濺鍍系統 - 21 -
3-2 量測分析 - 22 -
3-2-1 傅氏轉換紅外線光譜儀(Fourier Transform Infrared Spectroscopy ,FTIR) - 22 -
3-2-2 X光繞射儀(X-ray diffraction, XRD) - 24 -
3-2-3 電性量測 - 25 -
3-3 實驗過程 - 28 -
第四章實驗結果與討論 - 30 -
4-1 XRD量測結果與分析 - 30 -
4-1-1 改變製程溫度 - 30 -
4-1-2 改變製程脈衝頻率 - 32 -
4-2 FTIR量測結果與分析 - 33 -
4-2-1 改變製程溫度 - 34 -
4-2-2 改變製程脈衝頻率 - 35 -
4-3導電率量測結果與分析 - 37 -
4-3-1 改變製程溫度 - 37 -
4-3-2 改變製程脈衝頻率 - 39 -
4-4綜合比較實驗結果與討論 - 41 -
第五章結論 - 44 -
參考文獻 - 45 -

參考文獻

[1] M. A. Green, K. Emery, D. L. King, Y. Hishikawa, and W. Warta, "Solar Cell Efficiency Tables (Version 28)," Prog. Photovoltaics Res. Appl. 14, 455-461 (2006).
[2] L. Raniero, N. Martins, P. Canhola, S. Zhang, S. Pereira, I. Ferreira, E. Fortunato, and R. Martins, "Influence of the layer thickness and hydrogen dilution on electrical properties of large area amorphous silicon p-i-n solar cell," Solar Energy Mater. Solar Cells 87, 349-355 (2005).
[3] P. Ray, P. Chaudhuri, and P. Chatterjee, "Hydrogenated amorphous silicon films with low defect density prepared by argon dilution: application to solar cells," Thin Solid Films 403, 275-279 (2002).
[4] K. Kurobe, T. Fuyuki, and H. Matsunami, "Characterization of crystalline silicon grown by plasma-enhanced CVD for thin-film solar cells," Solar Energy Mater. Solar Cells 66, 1-9 (2001).
[5] U. Kroll, J. Meier, A. Shah, S. Mikhailov, and J. Weber, "Hydrogen in amorphous and microcrystalline silicon films prepared by hydrogen dilution," J. Appl. Phys. 80, 4971 (1996).
[6] D.R. Myers, A. Andreas, T. Stoffel, I. Reda, S. Wilcox, P. Gotseff, and B. Kay,"Radiometric Calibrations,Measurements, and Standards Development at NREL", NREL/CP-560-30964(2001)
[7] A. M. Nardes, A. M. De Andrade, F. J. Fonseca, E. A. T. Dirani, E. A. T. Dirani, R. Muccillo, and E. N. S. Muccillo, "Low-temperature PECVD deposition of highly conductive microcrystalline silicon thin films," Journal of Materials Science-Materials in Electronics 14, 407-411 (2003).
[8] R. Biswas and B. Pan, "Microscopic nature of Staebler-Wronski defect formation in amorphous silicon," Appl. Phys. Lett. 72, 371 (1998).
[9] 楊素華、蔡泰成，"太陽能發展，"科學發展月刊，390期，54(2005)。
[10] 莊嘉琛, "太陽能工程-太陽電池篇," 全華科技圖書股份有限公司, 中華民國九十年十月初版三刷。
[11] D. Staebler and C. Wronski, "Reversible conductivity changes in discharge-produced amorphous Si," Appl. Phys. Lett. 31, 292 (1977).
[12] A.J. Lewis,G. A.N Conneil, W. Paul and J.R. Pawlik, Proc.Int. Conf. Tetrally Bouded Amorphous Semicond., American Institute of Physics, New York 27 (1974)
[13] T. Su, P. C. Taylor, G. Ganguly, and D. E. Carlson, "Direct role of hydrogen in the Staebler-Wronski effect in hydrogenated amorphous silicon," Phys. Rev. Lett. 89, 015502 (2002).
[14] P. Stradins, "Light-induced degradation in a-Si: H and its relation to defect creation," Solar Energy Mater. Solar Cells 78, 349-367 (2003).
[15] S. Shimizu, M. Kondo, and A. Matsuda, "A highly stabilized hydrogenated amorphous silicon film having very low hydrogen concentration and a improved Si bond network", Journal of applied physics 97, 33522(2005)
[16] D. Rickerby and A. Matthews, "Advanced Surface Coatings: a Handbook of Surface Engineering," Blackie & Son Limited, (1991).
[17] 高正雄編著，"電漿化學，"復漢出版社，2-4(1999)。
[18] 楊錦章譯，"基礎濺鍍電漿，"電子發展月刊，第68期，13 (1983)。
[19] 陳陵援、吳慧眼，"儀器分析，"三民書局，99(2002)。
[20] J. M. Seo, M. C. Jeong, and J. M. Myoung, "Effects of hydrogen on poly-and nano-crystallization of a-Si: H prepared by RF magnetron sputtering," J. Cryst. Growth (2006).
[21] W. Du, X. Yang, H. Povolny, X. Liao, and X. Deng, "Impact of hydrogen dilution on microstructure and optoelectronic properties of silicon films deposited using trisilane," Journal of Physics D Applied Physics 38, 838-842 (2005).
[22] 許樹恩、吳泰伯，"X光繞射原理與材料結構分析，"民全書局(1993)
[23] H. Makihara, A. Tabata, Y. Suzuoki, T. Mizutani, "Effect of the hydrogen partial pressure ratio on the properties of μc-Si:H films prepared by rf magnetron sputtering, " 59, 785-791 (2000)
[24] C. Koc, M. Ito, M. Schubert, "Low-temperature deposition of amorphous silicon solar cells, " Solar Energy Materials & Solar Cells 68 227-236 (2001)
[25] S. Ray, " Transition from amorphous to microcrystal Si:H :effects of substrate temperature and hydrogen dilution", Journal of Non-crystalline Solids 299-302, 761-766 (2002)
[26] S. Klein, F. Finger, R. Carius, H. Wagner, and M. Stutzmann, "Intrinsic amorphous and microcrystalline silicon by hot-wire-deposition for thin film solar cell applications," Thin Solid Films 395, 305-309 (2001).

指導教授

李正中(Cheng-Chung Lee)

審核日期

2007-7-16

推文