無頻寬減損之微小化集總元件被動電路

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：69

、訪客IP：3.137.214.219

姓名

曾子豪(Tzu-hao Tseng) 查詢紙本館藏

畢業系所

電機工程學系

論文名稱

無頻寬減損之微小化集總元件被動電路
(Miniaturized lumped passive circuits with no bandwidth reduction)

相關論文

★ 用於行動上網裝置之智慧型陣列天線	★ 吸收式帶止濾波器之研製
★ 一維及二維切換式波束掃描陣列天線	★ 寬頻微型化六埠網路接收機
★ 具有良好選擇度的寬頻吸收式帶止濾波器	★ 微小化吸收式帶止濾波器之通帶改善
★ 共面波導帶通濾波器之研製	★ 微帶耦合線帶通濾波器與雙工器研製
★ 宇宙微波背景輻射陣列望遠鏡接收機之校準信號源研製	★ K-Band及Q-Band毫米波帶通濾波器設計
★ 薄膜製程射頻被動元件設計	★ 微波帶通低雜訊放大器設計
★ 積體式微波帶通濾波器之研製	★ 應用於高位元率無線傳輸系統之V頻段漸進式開槽天線陣列
★ 以多重耦合線實現多功能帶通濾波器	★ 以單刀雙擲帶通濾波器實現高整合度射頻前端收發系統

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本論文以被動積體電路微小化為目標，且以縮小尺寸同時不減損頻寬為設計主軸，因微波電路往往應用特定電氣長度為基本組件，是造成主、被動電路面積過大的主因；傳統縮小傳輸線方式會以集總元件等效T型或π型電路，但此等效僅於單一頻率成立，造成縮小面積後頻寬亦隨之減損。本研究以橋式T線圈，替代傳統T模型，將使用頻率範圍大幅提升，且同時達到微小化目的。電路實現上，使用平衡式電感與平行板電容，於砷化鎵(GaAs)與玻璃積體被動(GIPD)製程中實現，並應用於微型化寬頻四路威爾京生分波器、超寬頻多模態帶通濾波器與波束成型網路。
首先，以玻璃積體製程實現寬頻四路威爾京生分波器，中心頻率1.6 GHz，通帶內介入損耗最小值1.135 dB，以反射損耗大於20 dB定義頻寬可達117%，相位差0.269°，中心頻率下之尺寸僅為0.0245×0.0245 λ02。
其次，將橋式T線圈的寬頻特性應用於超寬頻多模態帶通濾波器，其中以砷化鎵積體製程實現三模態帶通濾波器，中心頻率6.85 GHz，以反射損耗大於20 dB定義，頻寬為86.6%，通帶內介入損耗最小值0.895 dB，尺寸為0.02×0.02 λ02；以玻璃積體製程實現者，中心頻率6.85 GHz，以反射損耗大於15 dB定義，頻寬為89%，最小介入損耗0.534 dB，電路尺寸為0.0376×0.0292 λ02；又為了增加通帶選擇度，以玻璃積體製程實現五模態帶通濾波器，中心頻率6.85 GHz，以反射損耗大於10 dB定義頻寬為96.6%，最小介入損耗1.327 dB，中心頻率下之尺寸僅為0.0548×0.0351 λ02。
最後，結合巴特勒矩陣與單刀四擲(SP4T)開關成波束成型網路，提供陣列天線調整輻射場型使用，電路以玻璃積體製程實現，中心頻率2.4 GHz，量測之介入損耗為-12.13±1.605dB (±45°path)與12.25±1.12dB (±135°path)，相位誤差-6.7°~-0.3°(±45°path)與2.5°~11.3°(±135°path)，以反射損耗大於15 dB定義頻寬為16.6%，功率消耗4.5 mW，中心頻率下尺寸為0.0368×0.0368 λ02。綜合以上電路皆遠小於傳統設計，且相較於理想傳輸線設計方式並無頻寬減損，證實橋式T線圈架構的確能對被動電路面積有大幅度的尺寸縮減，並不減損效能。

摘要(英)

In this thesis, very compact integrated passive circuits with high performance are presented. The major bottleneck of the size reduction of active and passive microwave circuits is the requirement of multiple transmission lines with given electrical length. Traditionally, lump elements are used to replace the transmission line, e.g. the equivalent T or π model. Although the size can be reduced, the bandwidth of the resulted microwave circuit is also reduced. This is due to the fact that those lumped T or π networks are equivalent to transmission line at single frequency only. In this work, the bridged T-coil is used to replace the conventional T model, such that the advantages of compact size and wide frequency bandwidth can both be achieved. The bridged T-coil can be implemented using balance inductor and metal-insulator-metal (MIM) capacitor in GaAs semiconductor IC process or Glass Integrated Passive Device (GIPD) process to achieve very compact size. It is then applied to the design of wideband four-way Wilkinson power divider, ultra-wideband multimode resonator Bandpass filter, and a switch beamforming network.
First of all, the proposed wideband four-way Wilkinson power divider is fabricated in GIPD process with a circuit size of 0.0245λ0 × 0.0245λ0 at 1.6 GHz. The measured minimum insertion loss is 1.18 dB, the fractional bandwidth is 117% with a return loss of greater than 20 dB, and the phase error is less than 0.269°. Then, by implementing the stepped-impedance resonator using the proposed bridged T-coil structure, several novel wideband multimode resonator Bandpass filters for ultra-wideband application are proposed. Specifically, the proposed triple-mode Bandpass filter fabricated in GaAs has a circuit size of only 0.0376λ0 × 0.0292λ0 at 6.85 GHz, a minimum insertion loss of 0.895 dB and a bandwidth of 86.6% for a return loss of greater than 10 dB. Another triple-mode Bandpass filter in GIPD process exhibits a circuits size of 0.02λ0 × 0.02λ0 at 6.85 GHz, a minimum insertion loss of 0.644 dB, and a fractional bandwidth of 89% for a return loss of greater than 15 dB. In order to improve the selectivity, a five-mode Bandpass filter is also designed using the GIPD process. Its circuit size is 0.0548λ0 × 0.0351λ0 at 6.85 GHz, the minimum insertion loss is 1.327 dB, and the fractional bandwidth is 96.6% for a return loss of greater than 10 dB. Finally, a compact GIPD beamforming network including a 4×4 Butler matrix and a SP4T switch is demonstrated, and the circuit size is only 0.037λ0 × 0.037λ0 at the center frequency of 2.4 GHz. The measured insertion losses are within -12.13±1.605dB (±45°path) and -12.25±1.12dB(±135°path), phase error are -6.7°~-0.3°(±45°path) and 2.5°~11.3°(±135°path), and the DC power consumption is 4.5 mW.
Compared with conventional designs, the above circuits are smaller in size with no bandwidth reduction as compared with their transmission-line based counterparts. The effectiveness of bridged T-coil on the design of miniaturized on-chip passive microwave circuit is also validated through proposed design examples.

關鍵字(中)

★ 波束成型網路
★ 功率分配器
★ 微小化
★ 橋式T線圈
★ 帶通濾波器

關鍵字(英)

★ bandpass filter
★ beamforming network
★ power divider
★ miniaturize
★ Bridged T-coil

論文目次

摘要 I
Abstract III
第一章緒論 1
1.1研究動機 1
1.2文獻回顧 3
1.3 章節介紹 5
第二章橋式T線圈 6
2.1 設計原理 6
2.2 理論推導 9
2.3 Q值與傳播常數討論 13
2.4 小結 15
第三章微小化寬頻四路威爾京生分波器 16
3.1 雙節電路架構與設計理論 16
3.2 微小化寬頻四路分波器設計 19
3.3 結論與文獻比較 26
第四章微小化多模態帶通濾波器 28
4.1 三模態帶通濾波器設計原理 28
4.2 微小化三模態寬頻帶通濾波器 33
4.2.1玻璃積體製程(GIPD) 33
4.2.2砷化鎵積體製程(GaAs) 38
4.3 五模態帶通濾波器設計 43
4.4 微小化設計 47
4.5 結論與文獻比較 53
第五章波束成型網路 56
5.1 巴特勒矩陣 56
5.2 波束成型網路 66
5.3 二極體黏著方式與偵錯 69
5.4 量測結果 75
5.5 結論與文獻比較 81
第六章結論 84
參考文獻 86

參考文獻

[1] E. J. Wilkinson, "An N-Way Hybrid Power Divider," Proc. IRE, vol. 8, no.1, pp. 116-118, Jan. 1960.
[2] R. Weber, RF/Microwave Power Generation Considerations, 1st ed., John Wiley & Sons, Inc., 2001.
[3] W. A. Davis, Radio Frequency Circuit Design,1st ed., John Wiley & Sons, Inc., 2010
[4] R. L. Haupt, Antenna Arrays: A Computational Approach, 1st ed., John Wiley & Sons, Inc., 2010
[5] E. L. Ginzton, W. R. Hewlett, J. H. Jasberg, and J. D. Noe, "Distributed amplification," Proc IRE, vol. 36, pp. 956-969, Aug. 1948.
[6] E. M. Chase and W. Kennan, "A power distributed amplifier using constant-R networks," Microwave and Millimeter-Wave Monolithic Circuits Symp., 1986. pp. 13-17
[7] T.-S. Horng, J.-M. Wu, L.-Q. Yang, and S.-T. Fang, "A novel modified-T equivalent circuit for modeling LTCC embedded inductors with a large bandwidth," Microw. Theory and Tech, vol. 51, no.12, pp. 2327-2333, Dec. 2003.
[8] D. M. Pozar, Microwave Engineering, 3rd ed., John Wiley & Sons, Inc., 2005.
[9] 張盛富, 戴明鳳, 無線通信之射頻被動電路設計, 全華科技圖書股份有限公司, 1998.
[10] S. Kaijun and X. Quan, "Novel ultra-wideband (UWB) multilayer slotline power divider with bandpass response," IEEE Microw. Wireless Compon. Lett., vol. 20, no. 1, pp. 13-15, Jan. 2010.
[11] S.-W Wong and L.Zhu, "Ultra-wideband power divider with good in-band splitting and isolation performances," IEEE Microw. Wireless Compon. Lett., vol. 18, no. 8, pp. 518-520, Aug. 2008.
[12] K. Seunghoon, J. Sanggeun, and J. Jinho, "Compact two-way and four-way power dividers using multi-conductor coupled lines," IEEE Microw. Wireless Compon. Lett., vol. 21, no. 3, pp. 130-132, Mar. 2011.
[13] M. M. Elsbury, P. D. Dresselhaus, N. F. Bergren, C. J. Burroughs, S. P. Benz, and Z. Popovic, "Broadband lumped-element integrated n-way power dividers for voltage standards," IEEE Trans. Microw. Theory and Tech, vol. 57, no. 8, pp. 2055-2063, Aug. 2009.
[14] K. Jeong-Geun and G. M. Rebeiz, "Miniature four-way and two-way 24 GHz Wilkinson power dividers in 0.13 um CMOS," IEEE Microw. Wireless Compon. Lett., vol. 17, no. 9, pp. 658-660, Sep. 2007.
[15] M. C. Scardelletti, G. E. Ponchak, and T. M. Weller, "Miniaturized Wilkinson power dividers utilizing capacitive loading," IEEE Microw. Wireless Compon. Lett., vol. 12, no. 1, pp. 6-8, Jan. 2002.
[16] C. Meng-Ju, W. Hsien-Shun, and T. Ching-Kuang, "A Ka-band CMOS Wilkinson power divider using synthetic quasi-TEM transmission lines," IEEE Microw. Wireless Compon. Lett., vol. 17, no. 12, pp. 837-839, Dec. 2007.
[17] L. Xing, P. Chang-Chien, F. Fong, D. Eaves, Z. Xiang, and M. Kintis, "Ultra-wideband power divider using multi-wafer packaging technology," IEEE Microw. Wireless Compon. Lett., vol. 21, no. 1, pp. 46-48, Jan. 2011.
[18] Z. Lei, S. Sheng, and W. Menzel, "Ultra-wideband (UWB) bandpass filters using multiple-mode resonator," IEEE Microw. Wireless Compon. Lett., vol. 15, no. 11, pp. 796-798, Nov. 2005.
[19] Y.-C. Chiou, Y.-F. Lee, J.-T. Tsai, and C.-C. Chen, "Planar multimode resonator bandpass filters with sharp transition and wide stopband," in IEEE MTT-S Int. Microwave Symp. Dig., Jun. 2008, pp. 439-442.
[20] M. Kaixue, K. C. B. Liang, R. M. Jayasuriya, and Y. Kiat Seng, "A wideband and high rejection multimode bandpass filter using stub perturbation," IEEE Microw. Wireless Compon. Lett., vol. 19, no. 1, pp. 24-26, Jan. 2009.
[21] Y.-C. Chiou, J.-T. Tsai, and C. Eisenhower, "Broadband quasi-Chebyshev bandpass filters with multimode stepped-impedance resonators (SIRs)," IEEE Trans. Microw. Theory and Tech, vol. 54,no. 8, pp. 3352-3358, Aug. 2006.
[22] Z.-H. Wu, Y.-H. Shim, and M. Rais-Zadeh, "Miniaturized UWB bandpass filters integrated with notch filters using a silicon-based integrated passive device technology," in IEEE MTT-S Int. Microwave Symp. Dig., Jun. 2011, pp. 1-4.
[23] Y.-T. Lee, K. Liu, R. Frye, H.-T. Kim, G. Kim, and B. Ahn, "Ultra-wide-band (UWB) band-pass-filter using integrated passive device (IPD) technology for wireless applications," Proc. Electronic. Compon. Technol. Conf., Jun. 2009, pp. 1994-1999.
[24] W. G. El Dine, H. Ezzeddine, S. Bila, and S. Verdeyme, "Three approaches for the realization of a Chebyshev cross-coupled UWB filter," in IEEE MTT-S Int. Microwave Symp. Dig., May. 2010, pp. 1360-1363.
[25] J. Y. Jeong and T. W.Kim, "Design and analysis of swapped port coupler and its application in a miniaturized butler matrix," IEEE Trans. Microw. Theory and Tech, vol. 58, no. 4, pp. 764-770, Apr. 2010.
[26] C.-W. Wang, T.-G Ma, and C.-F. Yang, "A new planar artificial transmission line and its applications to a miniaturized butler matrix," IEEE Trans. Microw. Theory and Tech, vol. 55, no. 12, pp. 2792-2801, Dec. 2007.
[27] C.-C. Chang, T.-Y. Chin, J.-C. Wu, and S.-F. Chang, "Novel design of a 2.5-GHz fully integrated CMOS butler matrix for smart-antenna systems," IEEE Trans. Microw. Theory and Tech, vol. 56, no. 8, pp. 1757-1763, Aug. 2008.
[28] G. Tudosie, H. Barth, and R. Vahldieck, "A compact LTCC butler matrix realization for phased array applications," in IEEE MTT-S Int. Microwave Symp. Dig., Jun. 2006, pp. 441-444.
[29] C. Wooyeol, P. Konggyun, K. Youngmin, K. Kihyun, and K. Youngwoo, "A V-band switched beam-forming antenna module using absorptive switch integrated with 4×4 butler matrix in 0.13-um CMOS," IEEE Trans. Microw. Theory and Tech, vol. 58, no. 12, pp. 4052-4059, Dec. 2010.
[30] M. Uthansakul and P. Uthansakul, "Experiments with a low-profile beamforming MIMO system for WLAN applications," IEEE Trans. Antennas Propag., vol. 53, no. 6, pp. 56-69, Dec. 2011.
[31] T.-Y. Chin, S.-F. Chang, J.-C. Wu, and C.-C. Chang, "A 25-GHz compact low-power phased-array receiver with continuous beam steering in CMOS technology," IEEE J. Solid-State Circuits, vol. 45, no. 11, pp. 2273-2282, Nov. 2010.
[32] J.-L. Kuo, Y.-F. Lu, T.-Y. Huang, Y.-L. Chang, Y.-K. Hsieh, P.-J. Peng, I.-C. Chang, T.-C. Tsai, K.-Y. Kao, W.-Y. Hsiung, J. Wang, Y.-A. Hsu, L. K.-Y. Lin, H.-C. Lu, Y.-C. Lin, L.-H. Lu, T.-W. Huang, R.-B. Wu, and H. W, "60-GHz four-element phased-array transmit/receive system-in-package using phase compensation techniques in 65-nm flip-chip CMOS process," IEEE Trans. Microw. Theory and Tech, vol. 60, no. 3, pp. 743-756, Mar. 2012.
[33] Y. Tiku and G. M. Rebeiz, "A 22-24 GHz 4-element CMOS phased array with on-chip coupling characterization," IEEE J. Solid-State Circuits, vol. 43, no. 9, pp. 2134-2143, Sep. 2008.
[34] 李駿華, "無頻寬減損之微小化功率分配器與巴特勒矩陣," 碩士論文國立中央大學, 2011.
[35] W. R. Eisenstadt and Y. Eo, "S-parameter-based IC interconnect transmission line characterization," IEEE Trans. Compon. Hybrids, Manuf. Technol., vol. 15, no. 4, pp. 483-490, Aug. 1992.
[36] W. Feng, and W. Che, " Novel Wideband Differential Bandpass Filters Based
on T-Shaped Structure," IEEE Trans. Microw. Theory and Tech, vol. 60, no. 6,
pp. 1560-1568, Jun. 2012.

指導教授

林祐生(Yo-shen Lin)

審核日期

2012-8-16

推文