A1050P鋁材非對稱壓延之實驗研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：63

、訪客IP：3.145.109.144

姓名

徐禮彬(Li-Pin Hsu) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

A1050P鋁材非對稱壓延之實驗研究
(Experimental of asymmetrical cold rolling with A1050P)

相關論文

★ 中尺寸LED背光模組之實驗研究	★ 利用有限元素法與反應曲面法探討金屬成型問題之最佳化設計-行星路徑旋轉鍛造傘齒輪為例
★ 以反應曲面法進行行動電話卡勾之最佳化設計	★ 以微分式內涵塑性理論分析材料受軸向循環負載之塑性行為
★ A1070在累進式背擠製下的機械性質與微結構之研究	★ 超音波輔助沖壓加工之應用-剪切、引伸與等通彎角擠製
★ 應用多體動力學於具循環氣體負載之迴轉式壓縮機振動預測模型建立	★ 以有限元素法與反應曲面法分析螺旋傘齒輪之旋轉鍛造最佳化設計
★ 超音波振動輔助鋁合金6061及低碳鋼S15C拉伸試驗之研究	★ 旋轉鍛造螺旋齒輪製程分析
★ 等通道扭轉彎角擠製之有限元素法及反應曲面法分析	★ 以有限元素法與反應曲面法分析增量式板金成形
★ 以有限元素法與反應曲面法分析螺旋傘齒輪之雙錐輥旋轉鍛造最佳化設計	★ 以有限元素法與反應曲面法分析兩點增量成形
★ 引伸成形加工問題之有限元素分析	★ 應用流函數法分析軸對稱熱擠製加工問題

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

摘要
本文主要是利用實驗探討板材經非對稱壓延加
工後，其彎曲的曲率、輥輪壓延力及輥輪扭矩和板
材壓下率的變化情形。非對稱壓延主要是以同徑異
週速為主，加上入口角度變化及乾摩擦、濕摩擦等
條件進行實驗。
實驗結果發現，壓延力及扭矩皆與縮減率、入
口角度成正比關係，且和週速比成反比關係。在濕
摩擦狀態下也有相同的情形，然在相同縮減率下，
濕摩擦所產生的壓延力及扭矩較乾摩擦小。曲率方
面，曲率變化主要是隨著壓下率有週期性振盪的波
形。

摘要(英)

Summary
The paper is a research with experiment to inquire into the variety of curvature, loading, torque and reduction after sheet is prsessed by asymmetrical rolling. The asymmetrical rolling mainly takes asymmetrical rolling as principle to experiment with the variety of entry angular and the conditions of dry, lubrication and etc.
In the experiment result, we can find loading and torque are direct proportioned to reduction and entry angular, but they are inverse proportioned to the ratio of the peripheral velocities of the upper roll and the lower roll. There is the same situation under the condition of lubrication, too. However, under the same reduction, loading and torque produced by lubrication are smaller than by dry.In curvature, the variety of it changing with reduction is wave of oscillation of a cycle.

關鍵字(中)

★ 非對稱
★ 滾壓
★ 切片法

關鍵字(英)

★ Forward slip
★ asymmetrical
★ rolling

論文目次

III
目錄
頁碼
摘要I
致謝II
目錄Ⅲ
圖表說明Ⅴ
緒論
1-1 前言 1
1-2 文獻回顧 1
1-3 研究動機 6
第一章實驗基礎
2-1 壓延種類 7
2-2 板材非對稱壓延 8
第二章實驗設備與方法
3-1 實驗設備
3-1-1 壓延設備 10
3-1-2 資料擷取系統 10
3-2 實驗方法
3-2-1 試片準備 10
3-2-2 實驗條件 11
3-2-3 潤滑條件 12
3-2-4 輥輪及工作平台之調整 12
3-2-5 實驗程序 13
3-3 摩擦係數的問題 15
3-4 曲率之測定
3-4-1 曲率計之矯正 17
3-4-2 曲率計之量測原理 17
IV
3-4-3 曲率量測方法之探討 18
3-5 入口角度的測定
3-5-1 入口角度設定 20
3-2-2 入口角度量測 20
3-6 應變率之計算
3-6-1 輥壓應變率推倒 20
3-6-2 輥壓實驗與拉伸試驗之應變率 21
3-7 拉伸試驗 22
第四章結果與討論
4-1 拉伸試驗 25
4-2 Forward slip 25
4-3 乾摩擦條件壓延
4-3-1 輥壓之壓延力及扭矩 26
4-3-2 輥壓之曲率 27
4-4 濕摩擦條件壓延 31
4-5 輥壓之總能量 33
第五章結論與建議 35
參考文獻 37
附錄 40

參考文獻

參考文獻
[1] W. Johnson and G. Needham, "An Experimental Study of Asymmetrical
Rolling," Applied Mechanics Convention, Cambridge, Instn. Mech.
Engrs. Vol. 180, p.270-281, April, 1966.
[2] W. Johnson and G. Needham, "Further Experiments in Asymmetrical
Rolling," Int. J. Mech. Sci., Vol. 8, p.443-455, 1966.
[3] P. Dewhurst, I. F. Collins and W. Johnson, "A Theoretical and
Experimental Investigation into Asymmetrical Hot Rolling," Int.
J. Mech. Sci., Vol. 16, p.389-397, 1974.
[4] I. F. Collins and P. Dewhurst, "A Slipline Field Analysis of
Asymmetrical Hot Rolling", Int. J. Mech. Sci., Vol. 17, p.643-651,
1975.
[5] N. Kamii and R. Terakado, "Study of the Rolling-Method of Hot
Finishing Tandem Mill by Rolls with Different Diameters," J. JSTP,
Vol. 17, p.966-972, 1976.
[6] K. Nakajima et al., "An Investigation of Rolling Property by
Rolling Experiment in Asymmetrical Strip Rolling," Proc. s-53
Sp. Conf. of JSTP, p.25-28, 1978.
[7] K. Nakajima and H. Yamamoto, "Effects of Frictional Coefficient
on Asymmetrical Strip Rolling," Proc. the 31th Joint Conf. of
JSTP, p.451-454, 1980.
[8] D. Pan and D. H. Sansome, "An Experimental Study of the Effect
of Roll Speed Mismatch on the Rolling Load during the Cold Rolling
of the Thin strip," Journal of Mechanical Working Technology,
Vol. 6, p.361-377, 1982.
[9] J. Pospiech, "A Note on the Influence of Some Factors Affecting
Curvature in the Flat Rolling of strip," Journal of Mechanical
Working Technology, Vol. 15, p.69-80, 1987.
[10] K. Narita et al., "The Characteristics of Curvature in
Asymmetrical Cold Rolling," Proc. s-63 Sp. Conf. of JSTP,
p.241-244, 1988.
[11] M. I. Ghobrial, "A Photoelastic Investigation on the Contact
Stresses Developed in Rolls during Asymmetrical Flat Rolling,"
Int. J. Mech. Sci., Vol. 31, p.751-764, 1989.
[12] 黃永茂，陳騰輝, "應用流線函數法於板材非對稱壓延之解析," 第十
七屆全國力學會議, p.1063-1069, 1993.
[13] 黃永茂，徐宏修, "應用流線函數法於壓延加工之研究－單層板非對
稱壓延速度場之修正," 第十九屆全國力學會議, p.171-178, 1995.
[14] A. B. Richelsen, "Numerical Analysis of Asymmetric Rolling
Accounting for Difference in Friction," J. Mater. Process.
Technol., Vol. 45, p.149-154, 1994.
[15] H. Dyja et al., "Theoretical and Experimental Analysis of Plates
Asymmetric Rolling," J. Mater. Process. Technol., Vol. 45,
p.167-172, 1994.
[16] Gow-Yi Tzou, "Analytical and experimental study on asymmetrical
sheet rolling"Int.J.Mech.Sci. Vol. 39,No3.pp. 289-303 , 1997.
[17] J.-S.Lu,O.-K.Harrer*,W.Schwenzfeier, F.D.Fischer,"Analysis
of the bending of the rolling material inasymmetrical sheet
rolling"International Journal of Mechanical Sciences pp.49-61,
1998.
[18] Gow-Yi Tzou, "Relationship between frictional coefficient and
frictional factor in asymmetrical sheet rolling",Journal of
Materials processing Technology,pp. 271-277,1999.
[19] M. Salimia, F. Sassanib"Modifed slab analysis of asymmetrical
plate rolling",International Journal of Mechanical Sciences 44 ,
pp.1999–2023, 2002.
[20] M. Salimi, M. Kadkhodaei, "Slab analysis of asymmetrical sheet
rolling",Journal of Materials Processing Technology 150 ,
pp.215–222, 2004.
[21] C.W.Knight, S.J.Hardy, A.W.Lees, K.J.Brown, "Investigations
into the influence of asymmetric factors and rolling parameters
on strip curvature during hot rolling",Journal of Materials
processing Technology 134,pp.180-189,2003.
[22] O. Hoffman and G. Sachs, "Introduction to the Theory of
Plasticity for Engineers," Fig. 19.1, McGraw-Hill Book Company,
New York, 1953.
[23] N. Bay, et al., "Cross Shear Roll Bonding," J. Mater. Process.
Technol., Vol. 45, p.1-6, 1994.
[24] T. Kawanami et al., "Effects of Work Roll Diameters, Driving
Method and Strip Bending on Characteristics of Rolling with
Different Work Roll Diameters," J. JSTP, Vol. 26, p.519-526,
1985.
[25] 產業板材輥軋加工，復漢出版社。
[26] Ekelund S., "The Analysis of Fators Influencing Rolling
Pressure and Power Consumption in the Hot Rolling of Sheet",
Steel, 93, 1993, P27-29, translated form Jernkontorets Ann. 1927,
Vol. 111,p.39, and 1928, Vol. 112,p.67.
[27] Designation：E8M-91, Standard Test Methods for Tension Testing
of Metallic Materials [Metric], p.150-168.
[28] W. F. Hosford and M. C. Caddell, "Metal forming Mechanics and
Metallurgy," Prentice-Hall International, Inc. p.55-60, 1993.
[29] K. Narita et al., "The Characteristics of Curvature in
Asymmetrical Cold Rolling," Proc. s-63 Sp. Conf. of JSTP,
p.241-244, 1988.

指導教授

葉維磬(WEI-CHING YEH)

審核日期

2006-7-20

推文