 |
|
|
|
以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數：29 、訪客IP：18.117.141.69
姓名 陳佳榮(CHIA-JUNG CHEN) 查詢紙本館藏 畢業系所 機械工程學系 論文名稱 6000系鋁合金析出舉動之HR-TEM研究 相關論文 檔案 [Endnote RIS 格式]
[相關文章]
[文章引用]
[完整記錄]
[館藏目錄]
至系統瀏覽論文 ( 永不開放)
摘要(中) 本實驗主要是以6022鋁合金（Al-0.6wt％Mg-1.0wt％Si）作為實驗材料，研究6022鋁合金板材經過不同條件的預備時效對於之後進行短時間人工實效析出舉動之影響。
實驗中藉由改變預備時效溫度與時間，並配合微差掃描分析儀(DSC)、硬度試驗、拉伸試驗及高解析度穿透式電子顯微鏡(HR-TEM)，探討預備時效對於析出物的影響。
由實驗結果得知，6022鋁合金預備實效的溫度越高，析出的顆粒可以越大，在預備時效之後施以170 ℃短時間人工實效之後強度也比較高。
6022鋁合金在短時間預備時效，析出粒子在HR-TEM之下觀察都為氣泡狀顆粒，預備時效溫度越高，氣泡狀析出物越大，分布也越稀疏。6022鋁合金在高溫預備時效(120 ℃、150 ℃)之後，再施以220 ℃ × 10min的復元處理之後，即可馬上析出棒狀β′，而低溫預備時效(70 ℃、90 ℃)則不能。摘要(英) In this experiment, the main material is AA6022（Al-0.6wt％Mg-1.0wt％Si）. The purples are to discuss the precipitated behavior in different pre-aging temperature and time and in short artificial aging time of plat AA6022.
By changing pre-aging temperature and time, DSC, hardness test, tensile test, and HR-TEM, we can discuss the effect of precipitation by pre-aging.
According to the experiment, in AA6022, higher pre-aging temperature, larger precipitated particle size we could gain. After pre-aging, we process artificial aging at 170 ℃,and we could get higher strenghth.
AA6022 process after pre-aging, the shape of the precipitated particle at HR-TEM are like bubbles. Higher pre-aging temperature, larger bubble precipitated particle, and the distribution is also scatter. AA6022 process by high temperature pre-aging(120 ℃、150 ℃), then treat 220℃ × 10min restoration, it can immediately precipitate roll shape β′, but low temperature pre-aging(70 ℃、90 ℃) can not.關鍵字(中) ★ 鋁合金
★ 6000系
★ 預備時效
★ HR-TEM關鍵字(英) ★ 6000 series
★ pre-aging
★ HR-TEM
★ aluminum alloy論文目次 目 錄
摘 要……………………………………………………………Ⅰ
謝 誌……………………………………………………………Ⅱ
目 錄……………………………………………………………Ⅲ
表目錄………………………………………………………………Ⅳ
圖目 錄…………………………………………………………………Ⅴ
第一章 緒論……………………………………………………………1
一、序言………………………………………………………………1
二、理論基礎與論文回顧……………………………………………2
2-1 Al-Mg-Si簡介………………………………………………… 2
2-2 Al-Mg-Si合金之析出硬化熱處理…………………………… 2
2-3 Al-Mg-Si合金的時效硬化過程……………………………… 4
2-3-1 Al-Mg-Si合金的時效析出序列與機構…………………4
2-3-2 Al-Mg-Si合金的兩段時效………………………………5
2-3-3復原處理…………………………………………………6
2-3-4 析出強化機構……………………………………………7
2-4 加工組織的回復………………………………………………8
2-4-1 再結晶……………………………………………………8
第二章 本文…………………………………………………………10
一、前言………………………………………………………………10
二、實驗步驟與方法…………………………………………………12
2-1 材料……………………………………………………………12
2-2熱處理…………………………………………………………12
2-3 微差掃描熱分析（DSC）………………………………………12
2-4 拉伸試驗………………………………………………………13
2-5硬度值量測……………………………………………………14
2-6穿透式電子顯微鏡觀察（TEM）…………………………….14
三、結果與討論………………………………………………………16
四、結論………………………………………………………………22
參考文獻…………………………………………………………….23參考文獻 參考文獻
[1] 日本輕金屬學會委員, ”鋁合金之組織與性質”, 日本輕金屬學會, pp.278, 1991
[2] L. Zhen, W. D. Fei, S. B. Kang, H. W. kim, ”Precipitation behaviour of Al-Mg-Si alloys with high silicon content”, Journal of Materials Science 32, pp.1895-1902, 1997
[3] Mahoto Takeda, Fumiyoshi Ohkubo, Tomohisa Shirai, Kouichiro Fukui, “Precipitation behaviour of Al-Mg-Si ternary alloys”, Materials Science Forum, vol.217-222, pp.815-820, 1996
[4] D.Apelian, S.Shivkumar, G.Sigworth, ” Fundamental Aspects of Heat Treatment of Cast Al-Si-Mg Alloys”, AFS Transactions, pp.727-741
[5] D.W.Pashley, M.H.Jacobs, J.T.Vietz, ”The Basci Processes Affecting Two-step Aging in an Al-Mg-Si Alloy”, Philosophical Magazine, vol.16, pp. 51-76, 1967
[6] G.Thomas, ”The Aging Characteristics of Aluminium Alloys”, Journal of the Institute of Metals, vol.90, pp.57-63, 1961
[7] 菅野幹宏, 鈴木壽, ”Transmission electron micrographs caused by some unfavorble factors in aluminum base alloys”, 輕金屬, vol.30, no.11, pp.653-663, 1980
[8] Bin-Lung Ou, Yoshikazu Tsuzuki, Kunihiko kishino, Katsutoshi Sasaki, Hajime Watanabe, ”Age-Hardenability of a 6000-Series(Al-Mg-Si)Alloy”, Furukawa Review, no.14, pp.157-162, 1995
[9] Toshiya Hirata, Shigeru Matsuo, Trans JIM, vol.13, pp.231, 1972
[10] M. H. Mulazimoglu, R. A. L. Drew, J. E. Gruzelski, Journal of materials science letters, vol.8, pp.297, 1989
[11] C. Panseri, T. Federighi, Journal of the institute of metals, vol.94, pp.99, 1966
[12] I. Kovacs, J. Lendvai, E. Nagy, Acta Metallurgica, vol.20, pp.975, 1972
[13] R. C. Dorward, Metallurgical Transactions, vol.4, pp.507, 1973
[14] Yoshio Baba, Akira Takashima, “Influence of Composition on the Two-Stage Aging of Al-Mg-Si Alloys”, Trans JIM, vol.10, pp.196-204, 1969
[15] S.B.Kang, L.Zhen, H.W.Kim, S.T.Lee, “Effect of cold rolling and aging treatment on mechanical property and precipitation behavior in a Al-Mg-Si alloy.,”Materials Science Forum vols.217-222, pp.827-832,1996
[16] W.Lorimer and R.B.Nicholsin; Acta Metallurgica, vol.14, pp.1009,1966
[17] 鈴木壽, 菅野幹宏, 伊藤吾朗, 日本輕金屬, vol.30, pp.609, 1980
[18] Robert E. Reed-Hill; Physical Metallurgy Priciples, 3rd ed. pp.532, 1991
[19] A.K. Vasudevan and R. D. Doherty; Aluminum Alloys - Contemporary Research and Applications, Academic Press, Inc., San Diego, pp.35～170, 1989.
[20] Kenji Matsuda, Shizuo Tada, Susumu Ikeno, Tatsuo Sato and Akihiko Kamio; Crystal System Of Rod-shaped Precipitates in an Al-1.0mass%Mg2Si-0.4mass%Si Alloy, Scripta Metallurgica ET Materialia, Vol. 32, NO.8, pp. 1175-1180, 1995.指導教授 歐炳隆(Bin-Lung Ou) 審核日期 2006-7-17 推文 plurk
funp
live
udn
HD
myshare
netvibes
friend
youpush
delicious
baidu
網路書籤 Google bookmarks
del.icio.us
hemidemi
facebook
twitter
google
reddit