流動式顆粒床過濾器之不對稱葉片設計與冷性能過濾機制研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：25

、訪客IP：18.188.101.251

姓名

吳建鋒(Chien-feng Wu) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

流動式顆粒床過濾器之不對稱葉片設計與冷性能過濾機制研究
(Asymmetric louver and cold filtration in Moving Granular Filter)

相關論文

★ 筆記型電腦改良型自然對流散熱設計	★ 移動式顆粒床過濾器濾餅流場與過濾性能之研究
★ IP67防水平板電腦設計研究	★ 汽車多媒體導航裝置散熱最佳化研究
★ 流動式顆粒床過濾器三維流場觀察及能性能測試	★ 流動式顆粒床過濾器冷性能測試
★ 流動式顆粒床過濾器過濾機制研究	★ 二維流動式顆粒床過濾器內部配置設計研究
★ 循環式顆粒床過濾器過濾性能研究	★ 流動式顆粒床過濾器之流場型態設計與研究
★ 流動式顆粒床過濾器之流動校正單元設計與分析研究	★ 流動式顆粒床過濾器之雙葉片型流動校正單元設計與冷性能過濾機制研究
★ 稻稈固態衍生燃料成型性分析之研究	★ 流動式顆粒床過濾器之滾筒式粉塵分離系統與冷性能過濾及破碎效應研究
★ 稻稈固態衍生燃料加入添加物成型性分析之研究	★ 顆粒床過濾連續化整合系統開發研究

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

至系統瀏覽論文 ( 永不開放)

摘要(中)

近十年來，美日歐等先進國家積極投入流動式顆粒床高溫廢氣淨化系統之研發。然而，在設計流動式顆粒床首要解決的條件就是當滯留區形成於葉片上的問題。當滯留區存在時，廢氣進入系統後將產生阻塞，導致壓降提升，過濾效率降低。
進出口葉片之垂直校正在此已提出適當的校正距離來消除滯留區的存在。本論文針對二維實驗結果作流場以及速度場分析。並在未來提供可迅速消除滯留區的最佳化設計並建立三維冷模測試搭配煤灰供應器，便以進行冷模過濾測試。
論文的第二部分在三維冷性冷測試壓降量測以及進口端速度分佈作探討。次葉片在流動試過濾器上扮演校正單元的角色，能夠有效的消除滯留區。
在冷性冷測試上，過濾效率也被測量出來。其過濾數據以及過濾器設計資訊也在本論文呈現出來。

摘要(英)

The granular moving bed filtration technology used for high-temperature gas cleanup has been developed in United States, Japan and EU countries in last decades. One of the key difficulties in design of granular moving bed filter is the formation of stagnant zones of filter granules in a moving bed with louvered walls. When stagnant zones exist, the dust coming with hot flue gas may plug the system. Gas pressure drop in moving bed continually rises and the filtration efficiency decreases remarkably.
Vertical shift of louvers on inlet or outlet wall of filter was proven to be an appropriate solution to diminish the stagnant zones. This paper presents the results of a study of the flow patterns and velocity fields of filter granules in a 2-D cross-flow moving granular bed systems with louvers shifted vertically in the moving bed. The optimum design that can diminish the stagnant zones effectively will be used to build a 3-D facility and install a dust generator in order to run the cold model filtration tests.
Second part of Thesis includes measurements of gas pressure drop and gas velocity distribution on inlet side of 3-D filter with louvers and sublouvers. Sublouvers are flow corrective elements that diminish stagnant zones in moving bed of filter media (silica sand).
In these cold tests the filter medium circulation rate and filtration efficiency were measured, too. The cold filtration test results, presented in this paper offer important data for designing the prototype of the moving granular bed filters.

關鍵字(中)

★ 滯留區
★ 熱空氣過濾
★ 流動式顆粒床
★ 主葉片與次葉片
★ 垂

關鍵字(英)

★ Louvers and Sublouvers
★ Vertical Shift
★ Dust Cake
★ Granular Moving-Bed
★ Dust Particles
★ Stagnant Zones
★ Hot Gas Filtration

論文目次

摘要 Ⅰ
致謝 III
目錄 IV
附表目錄 VI
附圖目錄 VI
符號說明 X
第一章簡介 1
1.1 研究背景 1
1.2 研究目的 7
第二章實驗設備和方法 10
2.1 二維實驗系統 10
2.1.1 實驗設備 10
2.1.2 實驗濾材與性質 12
2.1.3 實驗觀測與量測設備 14
2.1.4 流場實驗步驟 14
2.1.5 二維流場速度向量分析實驗過程 17
2.1.6 水平與垂直速度分佈分析比較 19
2.1.7 濾餅機制之原理方法 20
2.1.8 三維流場設計理論與實驗方法 21
2.1.9 專利設計介紹 38
第三章結果與討論 46
3.1 二維顆粒床模擬系統之設計與實驗結果 46
3.2 二維流場速度向量分析 68
3.3 三維冷性能測試實驗結果與討論 80
3.3.1 不同濾材之質量流率與對過濾器壓降與濾材過濾效率之關係 80
3.3.2 不同進口空氣流速對過濾器壓降與濾材過濾效率之關係 84
3.3.3 三維顆粒床自由面之進口端和出口端氣體速度分佈測量 89
第四章結論 93
4.1 二維流場結果 93
4.2 三維冷性能測試結果 95
參考文獻 95

參考文獻

1. Ahmadi, G. and Smith, D. H., 2002, “Gas flow and particle deposition in the hot-gas filter vessel of the Pinon Pine project,” Powder Technol., 128, pp. 1-10.
2. Johanson, J. R., 1966, “The use of flow corrective inserts in bins,” Trans. ASME J. Eng. Ind., 88, pp. 224-230.
3. Johanson, J. R. and Kleysteuber, W. K., 1966, “Flow corrective inserts in bins,” Chem. Eng. Prog., 62, No. 11, pp. 79-83.
4. Johanson, J. R., 1967/68, “The placement of insert to correct flow problems,” Powder Technol., 1, pp. 328-333.
5. 賴信璋，2003，流動式顆粒床過濾器過濾機制研究，國立中央大學機械工程學系。
6. 高偉智，2005，流動式顆粒床過濾器之流動校正單元設計與分析研究，國立中央大學機械工程學系。
7. 蔡信安，2006，流動式顆粒床過濾器之雙葉片型流動校正單元與冷性能過濾機制研究設計，國立中央大學機械工程學系。
8. Tüzün, U. and Nedderman, R. M., 1982, “An investigation of the flow
boundary during steady-state discharge from a funnel-flow bunker,”
Powder Technol., 31, pp. 27-43.
9. Morse, H. H., 1951. Patent US 2,255,052, Method of Effecting Contact in
a Pebble Heater.
10. Rong, G. H., Negit, S. C., and Jofriett, J. C., “Simulation of flow behaviour
of bulk solids in bins. Part 2 Shear bands, flow corrective inserts and velocity profiles,” Journal of Agricultural Engineering Research., 62, pp.
257-269.
11. Chou, C. S., Tseng, C. Y., Smid, J., Kuo, J. T., and Hsiau, S. S., 2000,
“Numerical simulation of flow patterns of disks in the symmetrical
louvered-wall moving granular filter bed,” Adv. Powder Technol., 11, pp.
279-296.
12. Chou, C. S., Tseng, C. Y., Smid, J., Kuo, J. T., and Hsiau, S. S., 2000,
“Numerical simulation of flow patterns of disks in the asymmetrical
louvered-wall moving granular filter bed,” Powder Technol., 110, pp.
239-254.
13. Nedderman, R. M., 1985, “Gravity flow of granular materials round
obstacles. I Investigation of the effects of inserts on flow patterns inside a
silo,” Chem. Eng. Sci., 40, pp. 325-336.
14. Nedderman, R. M., 1985, “Gravity flow of granular materials round
obstacles. II Investigation of stress profiles at the wall of a silo with
inserts,” Chem. Eng. Sci., 40, pp. 337-351.
15. Hsiau, S. S., Smid, J., and Wang, C. Y., 1999, “Velocity profiles of
granules in moving bed filters”, Chem. Eng. Sci., 54, pp. 293-301.
16. Hsiau, S. S., Smid, J., and Tsai F. H., 2004, “Placement of flow-corrective
elements in a moving granular bed with louvered walls,” Chem. Eng.
Process., 43, pp. 1037-1045.
17. Jenike Shear Tester, Model FT-5STEH. Jenike Shear Tester
&Consolidating Bench Operating Instructions. Revised, January 1998.
Jenike & Johanson, inc., One Technology Park Drive, Westford, MA,
USA.
18. 杜威達，2003，「二維流動式顆粒床過濾器內部配置設計研究」，國立
中央大學機械工程研究所。
19. Smid, J., Hsiau, S. S., Peng, C. Y., and Lee, H. T., 2002, “Granular moving
bed filters and adsorbers (GM-BF/A),” pp.17-96, Final Report for ITRI,
Hsinchu, R.O.C.
20. 馬家駒，2002，「流動式顆粒床過濾器冷性能測試」，國立中央大學機
械工程研究所。
21. Kuo, J. T., Smid, J., Hsiau, S. S., and Chou, C. S., 1998, “Stagnant zones
in moving bed filter for flue gas cleanup,” Filtration & Separation., 35, pp.
529-534.
22. Schwedes, J. and Strusch J., 1998, “Wall stress distributions in silos with
inserts, and loads on inserts,” In: “Silos. Fundamentals of theory, behavior
and design,” Ed. Brown C. J. and Nielsen J., London 1998, pp. 118-130.
23. Jenike, A. W., 1961, “Gravity flow of bulk solids,” Engng. Exp. Station.,
Bulletin No. 108, Univ. of Utah, Salt Lake City.
24. Jenike, A. W. and Johanson, J. R., 1974, “Bin for storage and flow of bulk
solids,” US Patent 3,797,707.
25. Jenike, A. W., 1964, “Storage and flow of solids,” Engng. Exp. Station.,
Bulletin No. 123, Univ. of Utah, Salt Lake City.
26. 行政院環境保護署環境檢驗所，2002，「排放管道中粒狀污染物採樣及
其濃度之測定方法」， NIEA A101.71C。
27. Hans, L. A., and Verfahrenstechnik GmbH, 1987, “Vorrichtung zum
Reinigen von Rauchgasen,” European Patent Office., DE 8314655.
28. Milsitz, F. J., 1992, “Moving bed gas/solids contact apparatus,” European
Patent Office., US 5165900.
29. Rueskamp Lufttechnik., Kernforschungszentrum., and Karlsruhe., 1987,
“Device for supporting and guiding layers,” European Patent Office., EP
0213298.
30. Peleschka G., and Werner W., “ 1978, “Procédé et appareil pour la
séparation de fractions fines en forme de poussiére de grains minéraux,
ainsi que de fractions d'hydrocarbures à bas point d'ébullition sous forme
de vapeurs et d'aérosols.” European Patent Office., FR 2395063.
31. Takeuchi Tatsurou., 1977, “Gas Adsorption Equipment OF Moving Bed
Type,” European Patent Office., JP 52082676.
32. Bikbau M. J., Bulatov N J., and Buyanov E. A., 1999, “Method OF And
Device For Cleaning OF Gases.” European Patent Office., RU 2132219.
33. Ievlev V. P., and Durach R. N. et al., 1982, “Granular Filter,” European
Patent Office., SU 957939.
34. Kiralosyan V. A., and Elovikov G. N. et al., 1983, “Granular Filter,”
European Patent Office., SU 995849.
35. Ploshenko I. G., and Yurchenko L. P. et al., 1987, “Granular Filter,”
European Patent Office., SU 1353475.
36. Samigulin R. L., Trubnikov V. V., and Samigulin K. R., 1990. ” European
Patent Office., SU 1560273.

指導教授

蕭述三(Shu-san Hsiau)

審核日期

2007-6-21

推文