![]() |
|
以作者查詢圖書館館藏 、以作者查詢臺灣博碩士 、以作者查詢全國書目 、勘誤回報 、線上人數:44 、訪客IP:18.222.6.144
姓名 周佳儀(Chia-yi Chou) 查詢紙本館藏 畢業系所 應用地質研究所 論文名稱 出磺坑背斜構造發育之三角剪切模型
(Simulation of the Chuhuangkeng anticline using the Trishear model)相關論文 檔案 [Endnote RIS 格式]
[Bibtex 格式]
[相關文章]
[文章引用]
[完整記錄]
[館藏目錄]
[檢視]
[下載]
- 本電子論文使用權限為同意立即開放。
- 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
- 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
摘要(中) 苗栗出磺坑背斜是台灣最早發現油氣之構造,直到現在仍被認為其深部地層之裂隙中蘊含大量油氣。出磺坑背斜出露地區一向為研究地質構造與探採資源的重要區域,因此擁有大量的地表、震測與鑽井資料,然而此區深部之震測接收訊號十分混亂,無法直接得知背斜深部之地層分布情況,因此岀磺坑背斜深部構造解釋仍有爭議。本研究利用三角剪切模式以解釋形成機制可能為斷層相關褶皺之出磺坑背斜構造發育,同時亦計算構造剖面中應變橢圓的分佈。至於裂隙分佈集中區域以及裂隙方向則可藉由三角剪切模式中的LNFE (Lines of No Finite Elongation) 得到。初步之參數敏感度分析結果顯示三角剪切模式中解釋斷層滑脫褶皺形貌的斷層傾角參數範圍,必須由以實際背斜構造之兩翼地層傾角決定;同樣以形成出磺坑背斜形貌為目的之情況下,背斜軸部高角度斷層傾角角度愈小則構造形成所需要之斷層滑移量愈大,而斷層傾角角度愈大則較少的斷層滑移量即可形成其高聳之幾何形貌;而三角剪切帶頂角角度愈大,則其褶皺兩翼愈寬廣且形貌對稱性愈低,角度愈小則褶皺兩翼愈緊閉,換句話說,近乎對稱的出磺坑背斜暗示著其形成過程中三角變形區之頂角角度局限在50至60度之範圍內。模擬成果更顯示,與地層方向平行之斷層其褶皺形貌無法符合出磺坑背斜之形貌,欲模擬如出磺坑背斜之斷層滑脫褶皺形貌,則必須在斷層末端假設一高角度斷層。本研究之三角剪切模式最佳模型顯示模擬出磺坑背斜之最佳參數值斷層傾角必須為50度,斷層滑移量3700公尺,三角剪切頂角角度60度,斷層前緣破裂距離與斷層滑移量之比值P/S為1,基底滑脫面為8.6公里深。然而,三角剪切模擬結果顯示,褶皺兩翼的地層傾角及厚度,會隨深度改變而明顯改變,此一結果與前人認為出磺坑背斜地層等厚且地表與深部地層傾角一致之看法並不一致;而利用三角剪切模式符合實際地表資料之模型雖然與前人對出磺坑背斜之幾何形貌略有差異,其分析之LNFE仍可符合實際裂隙之方向。 摘要(英) The Chuhuangkeng anticline is the first oil and gas producing structure in Taiwan. It is possible that considerable oil and gas is still stored in the fractures system of the strata. There is abundant geologic information in the Chuhuangkeng anticline. However, the quality of seismic reflection image in this area is extremely poor. Consequently, the geometry of the Chuhuangkeng anticline is mainly derived from surface geology indirectly and different geological models were proposed near the Chuhuangkeng anticline. It is hypothesized that the Chuhuangkeng anticline is a fault-related fold. Trishear model was utilized to simulate the geometry of the Chuhuangkeng anticline. The strained ellipse and directions of the fractures in Chuhuangkeng anticline (LNFE, Lines of No Finite Elongation) were also calculated. It is demonstrated that a steep fault under the Chuhuangkeng anticline is required in the trishear model to reproduce a nearly vertical and symmetrical fold. Based on the result of parametric study, the trishear angle of the Chuhuangkeng anticline is 50 to 60 degrees if one want to derive a nearly symmetrical fold. Besides, the ramp angle is 50 degrees, fault slip is 3700 meters, trishear angle is 60 degrees, P/S is 1, and the depth of the detachment is 8.6 kilometers for the best fitted model. Finally, the calculated LNFEs of trishear model have a similar dip with the actual dip of fractures observed in the well. Therefore, trishear model is potentially useful to evaluate the fracture system in an oil field. 關鍵字(中) ★ 出磺坑背斜
★ 斷層滑脫褶皺
★ 斷層相關褶皺
★ 三角剪切模式關鍵字(英) ★ decollement fold
★ fault-related fold
★ trishear model
★ Chuhuangkeng anticline論文目次 目錄
中文摘要................................................................................................i
英文摘要..............................................................................................iii
誌謝......................................................................................................iv
目錄.......................................................................................................v
圖目錄.................................................................................................vii
表目錄...................................................................................................x
一、 緒論 - 1 -
1.1 研究動機與目的 - 1 -
1.2 研究流程 - 2 -
1.3 論文架構 - 2 -
二、 研究區域地質構造概況 - 4 -
2.1 區域地質概述 - 4 -
2.2 地層 - 4 -
2.3 構造 - 6 -
三、 研究方法 - 10 -
3.1 三角剪切模式之簡介 - 10 -
3.2 三角剪切模式運動學分析之數值模擬 - 11 -
3.3 三角剪切模式利用地表地層資料逆推參數之方法 - 14 -
3.4 三角剪切模式於潛在裂隙分佈之應用 - 15 -
四、 出磺坑背斜幾何形貌模擬 - 22 -
4.1 以三角剪切模式模擬斷層滑脫褶皺 - 22 -
4.1.1 單純底滑之三角剪切變形 - 22 -
4.1.2 底滑加背斜軸部虛擬(斷層不擴展)高角度斷層 - 23 -
4.1.3 底滑加背斜軸部可擴展之高角度斷層 37
4.2 岀磺坑構造剖面模擬 40
4.2.1 底滑加背斜軸部虛擬(斷層不擴展)高角度斷層之模擬 41
4.2.2 底滑加背斜軸部高角度之擴展斷層之模擬 52
4.3 三角剪切模式對岀磺坑背斜之裂隙評估 61
五、 結論 64
參考文獻.............................................................................................................66參考文獻 [1]J. Namson, “Structure of the western foothills belt, Miaoli-Hsinchu area, Taiwan: (Ι) southern part” , Petroleum Geology of Taiwan, Vol 18, pp. 31-51, 1981.
[2]J. Namson, “Structure of the western foothills belt, Miaoli-Hsinchu area, Taiwan: (Ⅱ) central part” , Petroleum Geology of Taiwan, Vol 19, pp. 51-76, 1983.
[3]J. H. Hung, and D. V. Wiltschko, “Structure and kinematics of arcuate thrust faults in the Miaoli-Cholan area of western Taiwan” , Petroleum Geology of Taiwan, Vol 28, pp. 59-96, 1993.
[4]鍾開增,「苗栗地區麓山帶之地質構造」,國立中央大學,碩士論文,民國八十五年。
[5]R. D. Gold, E. Cowgill, X. F. Wang, and X. H. Chen, “Application of trishear fault-propagation folding to active reverse faults: examples from the Dalong Fault, Gausu Province, NW China” , Journal of Structural Geology, Vol 28, pp. 200-219, 2006.
[6]R. W. Allmendinger, T. Zapata, R. Manceda, and F. Dzelalija, “Trishear kinematic modeling of structures, with examples from the Neuqueu Basin, Argentina” , Thrust tectonics and hydrocarbon systems: AAPG Memoir, Vol 82, pp. 356-371, 2004.
[7]楊耿明,黃旭燦,凃嘉勝,周定芳,周佳儀,「臺灣西北部內麓山帶構造的三角剪切模式分析」,臺灣中油公司探採研究所,民國九十七年。
[8]王書偉,「出磺坑背斜地區邊坡穩定與水文特性之相關研究」,國立中央大學,碩士論文,民國九十二年。
[9]S. C. Sun, “The tertiary basins of offshore Taiwan: 2nd ASEAN council on petroleum(ASCOPE)conference, Manila” , Thrust tectonics and hydrocarbon systems: AAPG Memoir, Vol 82, pp. 125-135, 1981.
[10]J. Suppe, “Geometry and kinematics of fault-bend folding” , American Journal of Science, Vol 283, pp. 684-721, 1983.
[11]黃鐘,「台中盆地北側斷層構造與同震地表變形研究」,國立台灣大學,碩士論文,民國九十六年。
[12]洪日豪,「苗栗出磺坑背斜變形機制之研究」,國立台灣大學,碩士論文,民國七十三年。
[13]J. W. Granath, and R. M. I. Argakoesoemah, “Variations in structural style along the eastern Central Range thrust belt, Irian Jaya” , Proceedings of the Eighteenth Annual Convention of the Indonesian Petroleum Association, pp. 79-89, 1989.
[14]陳伯軍,「斷層擴展褶皺之斷層破裂距離與斷層滑移量比值(P/S)力學特性之研究」,國立中央大學,碩士論文,民國九十五年。
[15]W. R. Jamison, “Geometric analysis of fold development in overthrust terrances” , Journal of Structural Geology, Vol 9, pp. 207-219, 1987.
[16]E. A. Erslev, “Trishear fault-propagation folding” , Geology, Vol 19, pp. 617-620, 1991.
[17]S. Hardy, and M. Ford, “Numerical modeling of trishear fault propagation folding” , Tectonics, Vol 16, pp. 841-854, 1997.
[18]R. W. Allmendinger, “Inverse and forward numerical modelong of trishear fault-propagation folds” , Tectonics, Vol 17, pp. 640-656, 1998.
[19]N. Cardozo, “Trishear modeling of fold bedding data along a topographic profile” , Journal of Structural Geology, Vol 27, pp. 495-502, 2005.指導教授 董家鈞(Jia-jyun Dong) 審核日期 2008-7-21 推文 plurk
funp
live
udn
HD
myshare
netvibes
friend
youpush
delicious
baidu
網路書籤 Google bookmarks
del.icio.us
hemidemi
myshare