Functional Bearing Model (FBM) Analysis Under the Design Spectra of Near Fault Ground Motions

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：27

、訪客IP：18.116.24.111

姓名

艾芬娜(Alfinna Mahya Ummati) 查詢紙本館藏

畢業系所

土木工程學系

論文名稱

Functional Bearing Model (FBM) Analysis Under the Design Spectra of Near Fault Ground Motions
(Functional Bearing Model (FBM) Analysis Under the Design Spectra of Near Fault Ground Motions)

相關論文

★ 貼片補強構件之層間應力分析	★ 軌道不整檢測及識別方法
★ 混凝土結構分析之三維等效單軸組成材料模型	★ 卵形顆粒法向與切向接觸之等效線性彈簧值之推導與驗證
★ 以四面體離散化多面體系統之接觸分析與模擬	★ 軌道車輛三維動態脫軌係數之在線量測理論
★ 向量式DKMT厚殼元推導與模擬	★ 向量式預力混凝土二維剛架元之數值模擬與驗證
★ 向量式有限元應用於懸索橋非線性動力分析	★ 蛋形顆粒群之流固耦合分析
★ 複合版梁元素分析模型之橋梁動態識別法	★ 三維等效單軸應變與應力之材料組成模型
★ 人行吊橋的現有內力評估及動力分析	★ 薄殼結構非線性運動之向量式有限元分析法
★ 雷射掃描技術於鋼軌磨耗之檢測	★ 動態加載下的等效單軸應變與應力材料組成模型

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

大多數地震下的支承分析會假設有恢復力與摩擦力，但往往只能取得支承之最終位移和力量等數據，無法取得個元件之影響比重。本研究將使用FBM模擬支承，其中由三種元件組成，分別為於橋面板與支承上方間之摩擦元件、支承中間模擬橡膠之恢復力元件與支承下方與柱頂間之摩擦元件。
本研究使用近域地震波集集大地震TCU068, TCU102和TCU052進行分析，並符合規範之台中設計地震反應譜，再與遠域地震El-Centro大地震ELX354, ELX421和ELX600進行比較。在使用FBM支承系統於本橋梁進行分析時，將證實恢復力元件和摩擦元件可以獨立運算。本研究的目的為替換數種不同的摩擦係數以觀察橋梁動力反應之變化；其次，透過比較不同摩擦係數所造成之橋梁行為，找出最適合之摩擦係數使消能行為最佳；第三，確定最佳摩擦參數便於設計兩個甲板間隙，以避免地震發生時甲板發生碰撞；第四，確定最佳摩擦參數便於設計帽梁寬度，以避免地震發生時橋面版滑落。

摘要(英)

Functional Bearing Model (FBM) is an idea to represent 1 link analysis that used in common with divide it into 3 links based on each function. In this research, the rubber bearing divided into 3 elements as representation of rubber bearing system, they are: Friction element in the top of sliding interface between bearing and deck, Rubber in the middle link as a restoring element, and Frictional element in the bottom of sliding interface between bearing and column.
A shaking table size bridge proposed under the normalized peak ground acceleration under the design spectra of the near fault ground motions of Chi-Chi earthquakes TCU068, TCU102, and TCU052. In this research of FBM analysis, proof that the contribution of the rubber element and friction elements can be calculated independently.
The purposes of this research are: First, to study about the effect of variation of the friction coefficient that applied on the top surface and bottom surface of the rubber bearing system. Second, to study about determining several configuration of the friction coefficient to design a proper rubber bearing system. Third, to study about determining several configuration of the friction coefficient to design a gap between two decks in order to avoid the decks crashing when the earthquakes happen. Fourth, to study about determining several configuration of the friction coefficient to design enlargement of the column’s cap beam in order to avoid the decks falling when the earthquakes happen.

關鍵字(中)

★ 功能軸承模型
★ 近斷層
★ 反應譜
★ 橋梁分析
★ 動力分析

關鍵字(英)

★ Functional Bearing Model
★ Near Fault
★ Response Spectrum
★ Shaking Table Test Model
★ Bridge Analysis
★ Dynamic Analysis
★ Friction Coefficient
★ Rubber Bearing System

論文目次

CHAPTER I – INTRODUCTION 1
1.1 Background 1
1.2 Research Objectives 4
1.3 Research Scope and Limitation 6
1.4 Research Outline 6
CHAPTER II – LITERATURE REVIEW 8
2.1 Introduction 8
2.2 Highway Bridge Structure 8
2.3 Earthquake Ground Motion 9
2.3.1 Near Fault Earthquake 11
2.3.2 Earthquake Response in Linear System 12
2.3.3 Earthquake Response in Non-Linear System 13
2.4 Isolation System 15
2.4.1 Rubber Bearing 16
2.4.2 Functional Bearing Model (FBM) 17
2.5 Structural Optimization 18
2.5.1 Earthquake Response and Design Spectrum Analysis 18
2.5.2 Numerical Evaluation 20
2.6 Software Simulation 21
CHAPTER III – FUNDAMENTAL THEORY AND METHODOLOGY ANALYSIS 22
3.1 Functional Bearing Model (FBM) 22
3.2 State Space Analysis Process 23
3.2.1 Sticking State 26
3.2.2 Sliding State 27
3.3 Fundamental Theory 30
3.3.1 Free Body Diagram 30
3.3.2 Conditions 31
3.3.3 Sliding Mechanism 35
3.4 Research Flowchart 38
3.5 Modelling 40
3.5.1 Bridge Model 40
3.5.2 Material and Section Properties 41
3.5.3 Comparison Proposed Model with Previous Experimental Model 42
3.5.4 Resonance Possibility 46
3.6 Earthquake Input 47
3.6.1 Near Fault Earthquake 47
3.6.2 Far Fault Earthquake 51
3.6.3 Design Spectra Analysis 51
3.7 Bearing System 56
3.7.1 Functional Bearing Model (FBM) and Link Definition 57
3.7.2 Non Linear Boundary Condition 58
3.8 Variation of the Coefficient of Friction 59
3.9 System Analysis 61
3.9.1 Loading Definition and Loading Case 61
CHAPTER IV – NUMERICAL ANALYSIS: VARIATION OF FRICTION COEFFICIENT EFFECT ON FUNCTIONAL BEARING MODEL (FBM) ANALYSIS 63
4.1 Case Details 63
4.2 Near Fault Analysis 64
4.2.1 Duration of the Peak Response 64
4.2.2 Displacement Contribution 65
4.2.3 Energy Absorptions 69
4.2.4 Friction Element Contribution 73
4.3 Far Fault Analysis 76
4.3.1 Duration of the Peak Response 76
4.3.2 Displacement Contribution 77
4.3.3 Energy Absorptions 80
4.3.4 Friction Element Contribution 83
4.4 Conclusion 85
CHAPTER V – NUMERICAL ANALYSIS: BRIDGE FALLING PREVENTION 86
5.1 Case Details 86
5.2 Design A Proper Rubber Bearing 87
5.2.1 Maximum Deformation of the Rubber 87
5.2.2 Time Reference 89
5.2.3 Behavior of the Rubber Bearing System at the Certain Time 90
5.3 Design the Gap Distance of the Deck 100
5.3.1 Maximum Deck Displacement 100
5.3.2 Maximum Sliding Deformation of the Top Friction Surface 102
5.3.3 Time Reference 104
5.3.4 Behavior of the Rubber Bearing System at the Certain Time 104
5.4 Design the Column’s Cap Beam Size 111
5.4.1 Maximum Column Displacement 111
5.4.2 Maximum Sliding Deformation of the Bottom Friction Surface 113
5.4.3 Time Reference 115
5.4.4 Behavior of the Rubber Bearing System at the Certain Time 116
5.5 Standard Design Code 122
5.6 Conclusion 122
CHAPTER VI – OVERALL CONCLUSIONS 127
6.1 Conclusions 127
6.2 Recommendations 128
REFERENCES 130
APPENDIX 132

參考文獻

AASHTO LRFD, (2003). LRFD Bridge Design Manual. Minnesota: Minnesota Department of Transportation.
Ambrose, J. and Vergun D., (1995). Simplified Building Design for Wind and Earthquakes Forces Third Edition. Canada: John Wiley & Sons.
Borkowski, A. and Jendo, S., (1990). Structural Optimization Volume 2. New York: Plenum Press.
CALTRANS, (1994). Memo to Designers – Bridge Bearings. California: The California Department of Transportation.
Chang, K. C., Lu, C. H., and Liu, K. Y., (2011). Displacement-based Design for Highway Bridges with Functional Bearing System. NCREE. Taiwan.
Chopra, Anil K., (2013). Dynamics of Structures Theory and Applications to Earthquakes Engineering Fourth Edition. USA: Pearson Education.

Constantinou, M. C. & Tsopelas, P., (1995). Experimental Study of Bridge Seismic Sliding Isolation Systems. Elsevier. Page: 301-310.
CSiBridge, (2016). Bridge Seismic Design. USA: Computers & Structures, Inc.
Dowrick, D. J., (1977). Earthquake Resistant Design. New York: John Wiley & Sons.
Dowrick, D. J., (1987). Earthquake Resistant Design Second Edition. New York: John Wiley & Sons.
Ginsberg, Jerry H., (1988). Advance Engineering Dynamics. New York: Harper & Row.
Horton, C., (2018, February 7th). Taiwan Earthquake Toll Rises to 9 Dead, With Dozens Missing. Retrieved from https://www.nytimes.com.
Iemura, H., Taghikhany, T., Takahashi, Y., and Jain, S. K., (2005). Effect of Variation of Normal Force on Seismic Performance of Resilient Sliding Isolation System in Highway Bridges. Earthquake Engineering and Structural Dynamics. Page: 1777-1797.
Jangid, R. S., (2007). Optimum Lead Rubber Isolation Bearings for Near Fault Motions. Elsevier. Page: 2503-2513.
Jara, M. and Casas, Joan R., (2005). A Direct Displacement-Based Method for the Seismic Design of Bridges on Bi-linear Isolation Devices. Elsevier. Page: 869-879.
Kalpakidis, Ioannis V., and Constantinou, M. C., (2010). Principles of Scaling and Similarity for Testing of Lead-Rubber Bearings. Earthquake Engineering and Structural Dynamics. Page: 1551-1568.
Kikuchi, M., Aiken, and Ian, D., (1997). An Analytical Hysteresis Model for Elastomeric Seismic Isolation Bearings. Earthquake Engineering and Structural Dynamics. Page: 215-231.
Liu, K. Y., Chang, K. C., Chung, L. L., Tseng, T. C., Yang, C. Y., and Jang, C. L., (2013). Analytic Solution and Shaking Table Test on the Study of Bridge Structure with Functional Bearing System. National Center for Research on Earthquake Engineering, Taiwan.
Lu, L. Y. and Hsu, C. C., (2012). Experimental Study of Variable-frequency Rocking Bearing for Near Fault Seismic Isolation. Elsevier. Page: 116-129.
Schiff, A. J. and Tang, A. K. of American Society of Civil Engineers, (2000). Chi-Chi Taiwan Earthquake of September 21, 1999 Lifeline Performance. Virginia: ASCE.
SMS Tsunami Warning, (2011-2018). Earthquakes: Seismic Waves. Retrieved from http://www.sms-tsunami-warning.com.
Taghikhany, (2005). Variation of Axial Force due to Vibration of Flexible Girder in RSI System. Dissertation. Page: 49-147.
Takahashi, Y., Iemura, H., Yanagawa, S., and Hibi, M., (2004). Shaking Table Test for Frictional Isolated Bridges and Tribological Numerical Model of Frictional Isolator. 13 WCEE Canada. Paper No. 1531.
University of Tokyo, (2001-2002). Catalog of Earthquake Research Institute University of Tokyo: 7-1. The 1999 Chi-Chi, Taiwan, Earthquake. Retrieved from http://www.eri.u-tokyo.ac.jp.
Yu, N. T., et. al., (2015, November). Geological Record of Western Pacific Tsunamis in Northern Taiwan: AD 1867 and Earlier Event Deposits. Retrieved from https://www.researchgate.net.

指導教授

王仲宇(Chung-Yue Wang)

審核日期

2018-7-12

推文