博碩士論文 107323009 詳細資訊




以作者查詢圖書館館藏 以作者查詢臺灣博碩士 以作者查詢全國書目 勘誤回報 、線上人數:33 、訪客IP:44.206.248.122
姓名 夏浩剛(Hao-Kang Hsia)  查詢紙本館藏   畢業系所 機械工程學系
論文名稱 壓縮機噪音數值分析及其實驗比對
(Numerical Analysis of Compressor Noise and the Comparison with the Experiment)
相關論文
★ 四弦型非對稱光學讀取頭致動器模態共振分析與抑制★ 網路連接儲存裝置熱分析與設計
★ 小型垂直軸風力發電機之有限元素分析★ 平板受聲源作用之振動與輻射聲場分析
★ 壓電吸振器應用於平板的振動與噪音控制★ 主動式吸振器應用於薄板減振與減噪
★ 離散振動系統之分析軟體製作★ 有洞薄方板之動態分析與激振後之聲場
★ 撓性結構之主動振動控制★ 速度與位移回饋式壓電吸振器之減振研究
★ 以LabVIEW為介面之模態測試軟體製作★ 電壓回饋壓電吸振器對平板之振動控制
★ 可調式消音閥的分析與最佳設計★ 旋轉樑的動態分析與壓電吸振器之減振設計
★ 自感式壓電吸振器之設計與應用於矩形板之減振★ 多孔薄方板之振動與聲場分析
檔案 [Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   至系統瀏覽論文 (2025-7-31以後開放)
摘要(中) 本研究主要以模擬方法分析迴轉式壓縮機的殼內聲場,並與壓縮機殼內以及殼外量測數據的結果比對,再進行模型修正以使二結果更吻合。論文研究中使用有限元素法軟體ANSYS Acoustic ACTxR15.0進行聲場模擬,壓縮機的殼內聲場模擬空間由消音罩閥片入口處至壓縮機吐出口,以計算殼內聲壓,不考慮聲壓與壓縮機殼之耦合效應。為了更精準模擬壓縮機聲場中的不同邊界條件,文中透過材料聲學特性量測實驗,量測馬達內銅線線圈的阻抗值,以代入聲場模型中。模擬過程中亦討論了冷媒黏滯性與馬達線圈阻抗對殼內聲場的影響。最後將迴轉式壓縮機殼內聲場的模擬結果與公司端進行的實驗比對,探討殼內聲場與殼內/外量測噪音之關聯。
本研究之成果為以下數個項目,建立壓縮機殼內聲場模型及選擇參數,壓縮機殼內聲場模擬,壓縮機殼結構模態分析,模擬結果與量測實驗結果比對,聲學阻抗管實驗及銅線線圈聲學阻抗量測。
摘要(英) This research mainly studied the inner sound field of a rotary compressor. The FEM software ANSYS Acoustic ACTxR15.0 was used to simulate the sound field with the domain from the inlet of the muffler valve to the outlet of the compressor. The modal analysis of the structure of the compressor was also conducted by using ANSYS; but the coupling between the sound field and the structure was not considered. The simulated results and the measurement results were then compared. Numerical model of the acoustics and vibration of the compressor was modified according to the measurement results.
關鍵字(中) ★ 迴轉式壓縮機
★ 噪音數值分析
★ 聲場模擬
關鍵字(英) ★ Rotary Compressor
★ Noise Numerical Analysis
論文目次 目錄
摘要 I
Abstract II
目錄 III
圖目錄 VI
表目錄 IX
第一章 緒論 1
1.1研究背景與目的 1
1.2文獻回顧 3
1.3論文架構 5
第二章 基本理論 7
2.1 振動學基本理論 7
2.2 聲學基本理論 8
2.2.1 波動方程式 8
2.2.2 平面波 10
2.2.3 管路聲學阻抗 12
第三章 壓縮機聲場量測與阻抗管量測實驗 13
3.1 壓縮機聲壓量測方法 13
3.2 阻抗管聲學特性量測實驗 15
3.2.1 阻抗管實驗規劃與設計 15
3.2.2 阻抗管實驗步驟 19
第四章 ANSYS模擬方法 23
4.1 壓縮機殼內聲場空間模型與相關設定 23
4.2 聲場模擬方法 28
4.2.1 殼內聲壓模擬方法 28
4.2.2 殼外聲壓模擬方法 31
4.3 壓縮機結構模態相關設定 33
第五章 研究結果分析與討論 34
5.1 阻抗管聲學特性實驗 34
5.1.1麥克風校正 34
5.1.2 實驗可靠度 35
5.1.3 銅線線圈吸音係數量測 36
5.2 殼內量測聲壓結果分析 38
5.3 殼外量測聲壓結果分析 42
5.4 殼內、外量測聲壓結果討論 43
5.5 壓縮機殼內聲場比對-3600rpm 45
5.5.1單一聲源-消音罩閥片入口 46
5.5.2考慮冷媒動黏滯係數 49
5.5.3考慮線圈聲學阻抗 51
5.5.4雙聲源-消音罩閥片入口與馬達轉子 54
5.5.5殼內聲場結果分析與比對 55
5.6壓縮機殼外量測聲壓與殼內模擬聲壓之關聯性 59
5.7壓縮機殼外量測聲場之來源探討 61
第六章 結論與未來展望 63
6.1 結論 63
6.2 未來展望 63
參考文獻 67
參考文獻 [1] 黃以玫,2019,迴轉式壓縮機殼內空間聲場特性研究,國立中央大學,瑞智委託計畫結案報告,桃園市。
[2] 陳柏豪,2018,壓縮機殼內聲場模擬分析與材料聲學特性量測實驗,國立中央大學碩士論文,桃園市。
[3] Rao, S. S., 2011, "Mechanical Vibrations, Fifth Edition in SI Unit", PEARSON, U.S.A.
[4] 白明憲,2006,工程聲學,全華圖書股份有限公司,台北市。
[5] Kinsler, L. E., Frey, A. R., Coppens, A. B., and Sanders, J. V., 1982, Fundamentals of Acoustics, John-Wiley, New York
[6] Zhang, J. Q., Que, P. Z., Hu, Y. S., Zhang, R. T., and Shang, Y. J., 2016,” Mechanical Impact Noise Analysis of Rotary Compressor”, International Compressor Engineering Conference, Paper 2444, U.S.A.
[7] Wang, Q. N., Yan, K., and Li, H. Y., 2009, “Motor Noise Source Identification Based on Frequency Domain Analysis”, International Conference on Mechatronics and Automation., Changchun, China.
[8] Wen, Z. M., Zhang, R. T., Zhang, Y. S., Gu, H. H.,and Hu, Y. S., 2016,” Research On Low Frequency Vibration Of Rotary Compressor”, International Compressor Engineering Conference, Paper 2446., U.S.A.
[9] 孔祥強、陳麗娟、李瑛,2015,製冷壓縮機排氣管消聲器聲學及阻力特性仿真分析,第一章:消聲器結構及數學模型,山東科技大學機械電子工程學院。
[10] 陳琳、黃茲思,2004,迴轉式壓縮機消聲器的聲學特性分析,振 動工程學報,pp. 1019-1121,中國。
[11] 黃茲思,2003,旋轉式壓縮機消音器聲學特性理論與試驗研究,第三章:壓縮機消音器特性的有限元分析,上海交通大學。
[12] ANSYS, 2014, ANSYS Acoustic R15.0 Training Lecture Notes, ANSYS, Inc.
[13] 彭俊瑋,2017,壓縮機消音罩之進階分析與優化設計,國立中央大學機械工程研究所碩士論文,桃園市
[14] Wen, Z. M., Zhang, Y. S., Hu, Y. S., Zhang, R. T., Gu, H. H., 2018, "Research on Low Frequency Vibration of Rotary Compressor. ", International Compressor Engineering Conference, Paper 2603
[15] Shen, H., Huang, X. Q., Deng, Z. Q., Xie, L. C., Jin, H. S., 2018, "Research on Low Frequency Noise Caused by Beat Vibration of Rotary Compressor." International Compressor Engineering Conference, Paper 2528.
[16] ASTM E1050-12, 2014, "Standard Test Method for Impedance and Absorption of Acoustical Materials Using a Tube, Two Microphones and a Digital Frequency Analysis System".
[17] Chung, J. Y. and Blaser, D. A., 1980, "Transfer function method of measuring in-duct acoustic properties. II. Experiment." the journal of the Acoustical Society of America, Vol. 68, pp.907-913
[18] Silva, G. C. C., Nunes, M. A. A., Lopes, R. V., and Almeida, A. B., 2013, "Design and Construction of a Low Cost Impedance Tube for Sound Absorption Coefficients Measurements", 22nd International Congress of Mechanical Engineering, pp. 105-115, Brazil
[19] Atig, M., Dalmont, J. P. and Gilbert, J., 2004, “Termination impedance of open ended cylindrical tubes at high sound pressure level”, Comptes rendus de l’Academie des sciences. Serie IIb, Mecanique, Elsevier, 332 (4), pp.299-304
[20] Munjal, M. L., 2014, Acoustics of Ducts and Mufflers, Wiley, New York, U.S.A.
[21] 甲公司,內部文件資料。
[22] 沈冠廷,2019,迴轉式壓縮機設計變更隊噪音之影響,國立中央大學機械工程研究所碩士論文,桃園市。
[23] 甲公司,迴轉式壓縮機噪音量測資料。
[24] “ME 458 Engineering Noise Control”, 2000, [Online]. Available:
https://www.mne.psu.edu/lamancusa/me458/
指導教授 黃以玫 審核日期 2020-7-23
推文 facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu   
網路書籤 Google bookmarks   del.icio.us   hemidemi   myshare   

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明