應用於無線系統之多工器研製

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：12

、訪客IP：3.145.101.109

姓名

莊家寧(Chia-ning Chuang) 查詢紙本館藏

畢業系所

電機工程學系

論文名稱

應用於無線系統之多工器研製
(Multiplexer Design for WiMAX Applications)

相關論文

★ 利用缺陷型接地結構之雙頻微型平面倒F天線設計	★ 應用於第三代行動電話之倒Ｆ天線設計
★ 使用寄生元件之平面式倒F型雙頻天線設計	★ 利用寄生元件之平面式倒 F 型三頻天線設計
★ 無線通訊之三頻天線設計	★ 無線通訊之雙頻與三頻槽孔型天線設計
★ 應用於智慧型行動裝置之LTE/WWAN多頻單極天線設計	★ 應用於行動手持裝置之LTE/WWAN天線設計
★ 利用背腔式槽孔線結構之多頻段天線設計	★ 利用缺陷地面共振電路之介質量測技術
★ 應用於藍芽與全球衛星定位系統之電抗性負載型雙頻槽孔天線	★ 帶通圓形極化頻率選擇面之設計
★ 啞鈴型缺陷地面之介質量測電路分析與設計	★ 雙頻圓極化微波極化器設計
★ 利用微小共振電路之多頻段天線設計	★ 應用於X-band平面吸波器之薄型負載電路設計

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本論文中提出一應用於無線通訊系統(WiMAX)的雙工器與三工器，主要在改善傳統雙工器及三工器的連接方式。本次設計的雙工器結合了兩個帶通濾波器，分別為四分之一波長及二分之一波長共振器的帶通濾波器，因此旁生通帶可以被壓抑，不會影響高頻的濾波器，使隔離度可以提升。而在連結兩個濾波器時以共用耦合線饋入的方式，取代傳統雙工器用T接面(T-junction)連接濾波器，使得雙工器在輸入端匹配時，電路面積可以更進一步縮小，完成一個隔離度優於30 dB的雙工器。在三工器的部分，考慮一條微帶線在單一平面上最多只能與兩條微帶線耦合，所以我們將其中一個二分之一波長帶通濾波器用槽孔耦合的方式實現，利用將接地面開一個槽孔的方式，使訊號可以經由槽孔耦合到下層的饋入線，讓上層的傳輸線，除了耦合到相鄰的耦合線外，也可以經槽孔向下耦合到下層電路，完成連結的匹配，實現一隔離度優於20 dB的雙層板三工器。電路製作皆以FR-4 的板材完成，介電常數為1.6、介質損耗為0.02。從模擬與實作結果比較，皆具有很好的一致性。

摘要(英)

In the thesis, diplexers and triplexers for WiMAX applications are proposed. The proposed diplexer is mainly composed of a 1/2 ? and a 1/4 ? parallel-coupled-resonator bandpass filters. By using 1/4 ? parallel-coupled-resonator filter, the spurious passband will appear at 3f0. Thus, the isolation between two channels can be enhanced. In many conventional diplexer designs, T-junction is often used to connect both filters. This strategy could lead to the increase of the circuit area. Therefore, instead of the T-junction, common coupled lines are used to connect these two filters. By using the proposed matching network, a compact diplexer of high isolation (>30 dB) is thus obtained.
In the triplexer dsign, the third filter is added to the diplexer mentioned above. The signal is coupled to the third filter from the top layer to the bottom layer through the slot aperture on the ground. Then, we implemented input matching network of the triplexer without increasing extra area. The measured isolations of triplexer among channels are all better than 20 dB. All circuits are fabricated y using FR-4 substrate. The relative permittivity and loss tangent of the substrate are 4.4 and 0.02, respectively. The measured results are in agreement with the simulated results.

關鍵字(中)

★ 多工器

關鍵字(英)

★ multiplexer

論文目次

中文摘要 i
英文摘要 ii
目錄 iv
第一章緒論 1
1-1研究動機 1
1-2文獻回顧 2
1-3章節介紹 4
第二章耦合線帶通濾波器 5
2-1 簡介 5
2-2 二分之一波長共振耦合線濾波器 5
2-2-1 電路架構 5
2-2-2 濾波器設計 7
2-3 四分之一波長共振耦合線濾波器 11
2-3-1 電路架構 11
2-3-2 四分之一波長濾波器設計 13
2-4 總結 17
第三章雙工器之設計與實作 18
3-1 簡介 18
3-2雙工器分析與設計 18
3-2-1隔離度 19
3-2-2雙工器設計 20
3-3雙工器實作與量測 30
3-4 總結 32
第四章三工器之設計與實作 33
4-1 簡介 33
4-2 槽孔耦合帶通濾波器 34
4-2-1 槽孔耦合結構分析 34
4-2-2槽孔耦合帶通濾波器設計 37
4-3三工器分析與設計 41
4-3-1 抑制旁生通帶 42
4-3-2 三工器設計 44
4-4三工器電路實作與量測 57
4-5 總結 60
第五章結論 61
參考文獻 62

參考文獻

[1] D. M. Pozar, Microwave Engineering, 2nd ed. New Work: Wiley, 1998, ch. 8.
[2] H. W. Yao, A. E. Abdelmonem, J. F. Liang, X. P. Liang, K. A. Zaki, and A. Martin, “Wide-band Waveguide and ridge waveguide T-junctions for diplexer applications,” IEEE Trans. Microw. Theory Tech., vol. 41, no. 12, pp. 2166-2173, Dec. 1993
[3] T, Ohno, K, Wada, and O. Hashimoto, “Design methodologies of planar duplexers and triplexers by manipulating attenuation poles” IEEE Trans. Microw. Theory Tech., vol. 53, no. 6, pp. 2088 – 2095, June 2005.
[4] C.-W. Tang and S.-F. You; “Design Methodologies of LTCC Bandpass Filters, Diplexer, and With Transmission Zero, ” IEEE Trans. Microw. Theory Tech., vol. 54, no. 2, pp. 717 – 723, Feb 2006.
[5] D. Orlenko, K. Markov, S. Royak, A. Gordiyenko, O. Chernyakov, T. Kerssenbrock, G. Sevskiy, and P. Heide, “Novel high-rejection LTCC diplexers for dual-band WLAN applications, ” in IEEE MTT-S Int. Microwave Symp. Dig., June 2005, pp. 727-730.
[6] A. Yatsenko, D. Orlenko, S. Sakhnenko, G. Sevskiy, and P. Heide , “A Small-Size High-Rejection LTCC Diplexer for WLAN Applications Based on a New Dual-Band Bandpass Filter., ” in IEEE MTT-S Int. Microwave Symp., June 2007, pp. 2113 – 2116.
[7] D. Kim, D. H. Kim, J. I. Ryu, and J. C. Kim, “Highly integrated triplexers for WiMAX applications,” in IEEE MTT-S Int. Microwave Symp. Dig., June 2008, pp. 1091 – 1094.
[8] D. Kim, D. H. Kim, J. I. Ryu, C. D. Park, C. S. Kim, I. S. Song, and J. C. Kim, “A Compact WiMAX Diplexer Module with LTCC and FBAR Technologies” in Proc. 39th Eur. Microw. Conf., Rome, Italy, Oct. 2009, pp. 567-570.
[9] G. A. Lee, M. Megahed, and F. D. Flaviis, “Design of multilayer spiral inductor resonator filter and diplexer for system-in-a-package,” in IEEE MTT-S Int. Microwave Symp., June 2003, pp. 527 – 530.
[10] C. M. Tsai, S. Y. Lee, C. C. Chuang, and C. C. Tsai, “A folded coupled-line structure and its application to filter and diplexer design,” in IEEE MTT-S Int. Microwave Symp. Dig., June 2002, pp. 1927-1930.
[11] A. F. Sheta, J. P. Coupez, G. Tanne, S. Toutain, and J. P. Blot, “Miniature microstrip stepped impedance resonator bandpass filters and diplexer for mobile communications,” in IEEE MTT-S Int. Microwave Symp. Dig., June 1996, pp. 607-610.
[12] S. S. Oh, and Y. S. Kim, “A compact duplexer for IMT-2000 handsets using microstrip slow-wave open-loop resonators with high-impedance meander lines,” in Radio Wireless Conf., Aug. 2001, pp. 177-180
[13] B. Strassner and K. Chang, “Wide-band low-loss high-isolation microstrip periodic-stub diplexer for multiple-frequency applications,” IEEE Trans. Microw. Theory Tech., vol. 49, no. 10, pp. 1818-1820, Oct. 2001.
[14] S. Srisathit, S. Patisang, R. Phromloungsri, S. Bunnjaweht, S. Kosulvit, and M. Chongcheawchamnan, “High isolation and compact size microstrip hairpin diplexer,” IEEE Microw. Wireless Compon. Lett., vol. 15, no.2, pp. 101-103, Feb.2005.
[15] E. Goron, J.-P. Coupez, C. Person, Y. Toutain, H. Lattard, and F. Perrot, “Accessing to UMTS ﬁltering speciﬁcations using new microstrip miniaturized loop-ﬁlters,” in IEEE MTT-S Int. Microw. Symp. Dig., Jun. 2003, pp. 1599–1602.
[16] Jessada Kongpang, “A Compact Diplexer Using Square Open Loop with Stepped Impedance Resonators,“ in Asia-Pacific Microwave Conf., 2008, pp. 91-94.
[17] S. Hong, and K. Chang, “Stun-tuned microstrip bandpass filters for millimeter-wave diplexer design,” IEEE Microw. Wireless Compon. Lett., vol. 15, no.9, pp. 582-584, Sep. 2005.
[18] C.-F. Chen, T.-Y. Huang, C.-P. Chou, and R.-B. Wu, “Microstrip diplexer design with common resonator section for compact size but high isolation,“ IEEE Trans. Microw. Theory Tech., vol. 54, no. 5, pp. 1945 – 1952, May 2006.
[19] M.-H. Weng, C.-Y. Hung, and Y.-K. Su, “A hairpin line diplexer for direct sequence ultra-wideband wireless communications,“ IEEE Microw. Wireless Compon. Lett., vol. 17, no. 7, pp. 519 – 521, July 2007.
[20] P. -H. Deng, C.-H. Wang, and C. H. Chen “A Compact Microstrip Diplexers Based on a Dual-Passband Filter,“ in Asia-Pacific Microwave Conf., 2006, pp. 1-4.
[21] G. L. Matthaei and E. G. Cristal, “Multiplexer channel-separating units using interdigital and parallel- coupled filters,” IEEE Trans. Microw. Theory Tech., vol.13, pp.328-334, May 1965.
[22] C.-F. Chen, T.-Y. Huang, T.-M. Shen, and R.-B. Wu, “A Miniaturized Microstrip Common Resonator Triplexer without Extra Matching Network,” in Proc. Asia-Pacific Microwave Conference., 2006, pp. 1439 – 1422.
[23] H. W. Wu, K. Shu, M. H. Weng “Design of A Compact Microstrip Triplexer for Multiband Applications,“ In Proc. Eur. Microwave Conf, 2007, pp. 834 – 837.
[24] Zewani, M. Hunter, I.C. “Design of Ring-Manifold Microwave Multiplexers,“ in IEEE MTT-S Int. Microwave Symp. Dig., San Francisco, CA, pp. 689 – 692, June 2006.
[25] M-I. Lay and S-K Jeng, “A microstrip three-port and four-channel multiplexer for WLAN and UWB coexistence,”.IEEE Trans. Microw. Theory Tech., vol. 53, no 10, pp.3244-3250, October 2005.
[26] P.-H. Deng, N.-I. Lai, S.-K. Jeng, and C. H. Chen, “Design of Matching Circuits for Microstrip Triplexers Based on Stepped-Impedance Resonators,” IEEE Trans. Microwave Theory Tech., vol. 54, pp. 4185-4192, Dec. 2006.
[27] George L. Matthaei, “Direct-coupled, band-pass filters with ?????resonators,” IRE International Convention Record, vol. 6, Part 1, pp. 98-111, Mar 1958.
[28] T. Tanaka, K. Tsunoda, and M. Aikawa,“Slot-coupled directional couplers between double-sided substrate microstrip lines and their applications,＂IEEE Trans. Microw. Theory Tech., vol. 36, no. 12, pp. 1752-1757, Dec. 1988.
[29] Y.-S. Lin, P.-Y. Chang, and C.-L. Lin, “ Compact parallel-coupled microstrip diplexers with good stopband rejection” in Proc. Asia-Pacific Microwave Conference., 2009, pp. 2321 – 2624.
[30] S. Hong and K. Chang; “A 10-35 GHz Six-Channel Microstrip Multiplexer for Wide-Band Communication Systems, ” IEEE Trans. Microw. Theory Tech., vol. 54, no. 4, pp. 1370 – 1378, April 2006.
[31] J. S. Hong, M. J. Landcaster, Microstrip Filters for RF/Microwave Applicatio, John Wiley & Sons, Inc., 2001

指導教授

丘增杰(Tsen-chieh Chiu)

審核日期

2010-6-11

推文