博碩士論文 107521132 詳細資訊




以作者查詢圖書館館藏 以作者查詢臺灣博碩士 以作者查詢全國書目 勘誤回報 、線上人數:38 、訪客IP:44.220.247.152
姓名 歐陽愈(Yu Ouyang)  查詢紙本館藏   畢業系所 電機工程學系
論文名稱 具有寬高頻處止帶之寬頻帶通濾波器的設計與分析
(Design and Analysis of Wideband Bandpass Filter with Wide Upper Stopband)
相關論文
★ 應用於微波之多頻帶通濾波器之設計★ 使用可開關式帶通濾波器之低相位雜訊雙頻振盪器研製
★ 共平面波導饋入槽孔偶極天線之寬頻與多頻應用★ 可具任意通帶之可調式多工器
★ 利用非對稱步階式阻抗設計寬通帶寬止帶雙工器★ 基於散佈式耦合饋入架構之可開關式帶通濾波器
★ 共平面波導饋入之寬頻雙圓極化天線★ 基於多共振路徑所設計之印刷式多頻帶天線
★ 四通道可切換式帶通濾波器之研究★ 雙模態寬阻帶之基板合成波導濾波器
★ 微小化倍頻壓抑直交分合波器之研製★ 可繞式小型偶極天線之研製
★ 使用多重模態共振器實現多功能帶通濾波器★ 應用於Radio-over-Fiber系統之超高速微波光子發射器
★ 使用長饋入線架構研製小型且具有高隔絕度的多工器★ 具有寬截止頻帶的帶通濾波器之研製
檔案 [Endnote RIS 格式]    [Bibtex 格式]    [相關文章]   [文章引用]   [完整記錄]   [館藏目錄]   [檢視]  [下載]
  1. 本電子論文使用權限為同意立即開放。
  2. 已達開放權限電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
  3. 請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。

摘要(中) 本文介紹三種射頻印刷電路板被動寬頻帶通濾波器並具有諧波抑制的設計方法,並且都是以三傳輸極點為基礎作設計,最後再將這些方法比較其優缺點。
第一種設計方法先設計一低通濾波器,再並聯三短路殘段至特定節點,此處會因回波損耗太差,所以須將輸出及輸入端的地方加上一段傳輸線作阻抗匹配。第二種方法與上述方法不同之處在柴比雪夫低通濾波器五處節點接上短路殘段,此方法的優點在於不用加上一段傳輸線作阻抗的匹配,所以能夠將原本低通濾波器的截止頻率固定住。
第三種設計為連續耦合之帶通濾波器,藉由給定的傳輸零點位置可直接合成出基礎的集總元件電路,並將此濾波器的集總電路元件由ABCD矩陣求出,並分由三個區塊的架構將集總元件轉為分佈元件。此方法之特點為濾波器的個數N會與傳輸零點的數目相同。
本文第四章用三種設計方法在RO4003C比較,其中兩種方法有實作之結果,印刷電路板之介電係數為3.55、板厚32毫英寸,最後以表格列出效能。
摘要(英) In this thesis, three structures of wideband bandpass filter(BPF) are presented and analyzed respectively. Three transmission poles in passband are chosen in the comparison table.
The first design differs from transversal approaches that it is based on the choice of a lowpass filter(LPF), to which 3 shunt shorted stubs are added at specific nodes. However, the return loss at this stage is poor and this is corrected by quarter wavelength of the matching elements. The second design is modified by the previously mentioned method, which has the same fundamental LPF; nevertheless, connected with 5 shunt short stubs instead. One of the advantage from the 1st design is that the upper passband edge is fixed because matching elements is not necessary in the procedure.
The last structure is a general sequentially coupled wideband BPF. The basic lumped-circuit model can be directly synthesized by given specifications transmission zeros (TZs). Circuit elements can be sequentially extracted from the ABCD matrix. The synthesized lumped element circuit consist of three parts of elementary lumped element circuit that can be approximated by distributed element circuits respectively. Consequently, there are N number of TZs made by the same number resonators in the upper stopband.
In the end of this thesis, 3 proposed methods are compared in the discussion. Two of them are implemented on RO4003C with dielectric constant 3.55 and dielectric thickness 32 mil.
關鍵字(中) ★ 寬頻帶通濾波器
★ 寬止帶
關鍵字(英) ★ Wideband Bandpass Filter
★ Wide Upper Stopband
論文目次 中文摘要 ………………………………………………………… i
Abstract ………………………………………………………… ii
誌謝 ………………………………………………………… iii
目錄 ………………………………………………………… v
圖目錄 ………………………………………………………… vii
表目錄 ………………………………………………………… xi
第一章 緒論…………………………………………………… 1
1-1
1-2
1-3 研究動機………………………………………………
文獻回顧………………………………………………
章節介紹……………………………………………… 1
1
3
第二章 使用五階柴比雪夫低通濾波器設計寬頻帶通濾波器 4
2-1 柴比雪夫低通濾波器設計…………………………… 5
2-1-1 柴比雪夫低通濾波器基本電路………………… 6
2-1-2 Richard’s transformation…………………… 8
2-1-3 Kuroda’s identities…………………………… 9
2-2 並聯三短路殘段至特定節點………………………… 14
2-3
2-4 頭尾加傳輸線作阻抗匹配……………………………
並聯五短路殘段至特定節點………………………… 15
16
第三章 直接合成設計連續耦合寬頻帶通濾波器…………… 21
3-1 濾波器方程式………………………………………… 22
3-2 基本電路架構………………………………………… 31
3-2-1 集總I/O電路近似轉換………………………… 32
3-2-2 中間共振器耦合之電感近似轉換……………… 34
3-2-3 共振器近似轉換………………………………… 36
3-3 元件值萃取…………………………………………… 38
3-4 設計範例……………………………………………… 42
第四章 比較三種設計方式的效能…………………………… 52
4-1 RO4003C板材可實現之最大頻寬…………………… 52
4-2 RO4003C板材可實現之最小頻寬…………………… 56
4-3 量測結果……………………………………………… 59
第五章 結論…………………………………………………… 64
參考文獻 ………………………………………………………… 65
參考文獻 [1] S. Amari, F. Seyfert, and M. Bekheit, “Theory of coupled resonator microwave bandpass
filters of arbitrary bandwidth,” IEEE Trans. Microw.Theory Techn., vol. 58, no. 8, pp. 2188–2203, Aug. 2010.
[2] R. Zhang and L. Zhu, “Synthesis of dual-wideband bandpass filters with source–load
coupling circuit,” IEEE Trans. Microw. Theory Tech.,vol. 62, no. 3, pp. 441–449, Mar.
2014.
[3] Li, Z., Wu, K.-L.: ‘Direct synthesis and design of a general sequentially coupled
wideband bandpass filter with N-transmission zeros’, IEEE Trans.Microw. Theory Tech., 2016, 64, (5), pp. 1484–1495
[4] Li, Z., Wu, K.-L.: ‘Synthesis and design of dual-wideband filter with composite series and
shunt resonators’. Proc. IEEE MTT-S Int. MicrowaveSymp. Digest, Honolulu, HI, June 2017, pp. 360–363
[5] Zhang, R., Zhu, L.: ‘Synthesis and design of wideband dual-band bandpass filters with
controllable in-band ripple factor and dual-band isolation’, IEEETrans. Microw. Theory Tech., 2013, 61, (5), pp. 1820–1828
[6] R. J. Wenzel, “Exact design of TEM microwave networks using quarterwavelines,” IEEE
Trans. Microw. Theory Techn., vol. MTT-12, no. 1,pp. 94–111, Jan. 1964.
[7] M. C. Horton and R. J. Wenzel, “General theory and design of optimum quarter-wave
TEM filters,” IEEE Trans. Microw. Theory Techn.,vol. MTT-13, no. 5, pp. 316–327, May 1965.
[8] C.-L. Hsu, F.-C. Hsu, and J.-T. Kuo, “Microstrip bandpass filters for ultra-wideband
(UWB) wireless communications,” in IEEE MTT-S Int. Microw. Symp. Dig., Jul. 2005, pp. 679–682.
[9] R. Gomez-Garcia and J. I. Alonso, “Systematic method for the exact synthesis of ultra-
wideband filtering responses using high-pass and lowpass sections,” IEEE Trans. Microw. Theory Techn., vol. 54, no. 10,pp. 3751–3764, Oct. 2006.
[10] R. Zhang, S. Luo, L. Zhu, and L. Yang, “Synthesis and design of harmonic-suppressed
wideband bandpass filters with mixed modified Richard’s transformations,” IEEE Microw. Wireless Compon. Lett., vol. 27, no. 5, pp. 455–457, May 2017.
[11] R. Zhang, S. Luo, L. Zhu, and L. Yang, “Synthesis and design of miniaturized wideband
bandpass filters with scaled transmission line for spurious-response suppression,” IEEE Trans. Microw. Theory Techn., vol. 65, no. 8, pp. 2878–2885, Aug. 2017.
[12] I. M. Salama, “A new approach for the design of wideband band-pass filters with
extended stop-bands,” in Proc. Symp. Texas Wireless Microw.Circuits Syst., Apr. 2013, pp. 1–4.
[13] H. N. Shaman, A. M. Almughamis, A. M. Alamro, and Y. S. Alharthi,“Compact ultra-
wideband (UWB) bandpass filter with wideband harmonic suppression,” in Proc. 21st Int. Conf. Microw., Radar WirelessCommun. (MIKON), May 2016, pp. 1–4
[14] J.-S. Hsieh and C.-M. Tsai, “Synthesis of filters with stub-loaded multiple-mode
resonators,” IEEE Microw. Wireless Compon. Lett.,vol. 21, no. 10, pp. 516–518, Oct. 2011.
[15] L.-Y. Ren and H. He, “Wide stopband bandpass filter based on dual plane
microstrip/interdigital DGS slot structure,” Electron. Lett., vol. 45,no. 25, pp. 1331–1332, Dec. 2009.
[16] B. Sahu, P. Tripathi, S. Singh, M. K. Meshram, and S. P. Singh, “Investigation on
compact modified wideband interdigital bandpass filter with wide stopband using spurlines and defected ground structures,”Microw. Opt. Technol. Lett., vol. 58, no. 11, pp. 2634–2639, Nov. 2016.
[17] J.-T. Kuo, W.-H. Hsu, and W.-T. Huang, “Parallel coupled microstrip filters with
suppression of harmonic response,” IEEE Microw. Wireless Compon. Lett., vol. 12, no. 10, pp. 383–385, Oct. 2002.
[18] J.-T. Kuo, M. Jiang, and H.-J. Chang, “Design of parallel-coupled microstrip filters with
suppression of spurious resonances using substrate suspension,” IEEE Trans. Microw. Theory Techn., vol. 52, no. 1, pp. 83–89, Jan. 2004.
[19] J. T. Kuo and M. Jiang, “Enhanced microstrip filter design with a uniform dielectric
overlay for suppressing the second harmonic response,” IEEE Microw. Wireless Compon. Lett., vol. 14, no. 9, pp. 419–421, Sep. 2004.
[20] J. D. Rhodes, Theory of Electrical Filters, John Wiley & Sons, New York,1976.
[21] Weisstein, Eric W (1999). "Hurwitz polynomial". Wolfram Mathworld. Wolfram
Research. Retrieved July 3, 2013.
[22] Reddy, Hari C. (2002). "Theory of two-dimensional Hurwitz polynomials" . The Circuits
and Filters Handbook, 2nd Ed. CRC Press. pp. 260–263. Retrieved July 3, 2013.
[23] Parks, Thomas W., and C. Sidney Burrus. Digital Filter Design. New York:John Wiley
& Sons, 1987, chap. 7
[24] R. J. Cameron, C. M. Kudsia, and R. R. Mansour, Microwave Filters for Communication
Systems: Fundamentals, Design and Applications.New York, NY, USA: Wiley, 2007.
[25] D. M. Pozar, Microwave Engineering, 2nd ed. New York:Wiley, 1998
[26] H. Ozaki and J. Ishii, Synthesis of a class of strip-line filters, IRE Trans. Circuit
Theory,CT-5, 1958, 104–109.
[27] Johannes A. G. Malherbe, "Wideband Bandpass Filter With Extremely Wide Upper
Stopband", Microwave Theory and Techniques IEEE Transactions on, vol. 66, no. 6, pp. 2822-2827, 2018.
[28] Hong, J.-S., Lancaster, M.J.: ‘Microstrip filters for RF/microwave applications’ (John
Wiley & Sons, Inc., New York, NY, USA, 2004)
[29] https://rogerscorp.com/en/advanced-connectivity-solutions/ro4000-series-
laminates/ro4003c-laminates
[30] K. C. Gupta, R. Garg, I. Bahl, and P. Bhartia, “Microstrip Lines and Slotlines,” third
Edition, Artech House, 2013
[31] B. S. Yarman, “Design of Ultra Wideband Power Transfer Networks” Wiley, 2010.
[32] J. D. Rhodes and S. A. Alseyab, “The generalized Chebyshev low-pass prototype filter,”
IEEE Transactions on Circuit Theory, vol. 8, pp. 113-125, 1980.
指導教授 凃文化(Wen-Hua Tu) 審核日期 2021-1-15
推文 facebook   plurk   twitter   funp   google   live   udn   HD   myshare   reddit   netvibes   friend   youpush   delicious   baidu   
網路書籤 Google bookmarks   del.icio.us   hemidemi   myshare   

若有論文相關問題,請聯絡國立中央大學圖書館推廣服務組 TEL:(03)422-7151轉57407,或E-mail聯絡  - 隱私權政策聲明