參考文獻 |
[1] H. J. Sokol, "Comparison between ISO AND ASTM methods for polyproplene injection molding and mechanical testing," Johns Hopkins University, MSc. Thesis, Baltimore, Maryland, May 2018.
[2] J. C. Ahlbrandt, "Mechanical properties of rapid manufacturing and plastic injection molding," University of Missouri – Columbia, MSc. Thesis, December 2014.
[3] S. Elsheikhi, "A holistic approach to injection moulding optimisation for product quality and cost through the characterisation of reprocessed polymetric materials and process monitoring," University of Bradford, PhD. Thesis, 2011.
[4] D. J. Hallowell, "An investigation of weldline strength issues associated with injection molded products ," Lehigh University, MSc. Thesis, December 2001.
[5] E. SMITH, "Reactive resin transfer over-moulding of continuous fibre reinforced load introduction features ," University of Queensland, B.Eng. Thesis, June 2017.
[6] R. Tandon, "A study about the effect of addition of carbon nanofibers on the strain-rate sensitivity of thermoplastic polymer matrix nanocomposites manufactured by ultrasonication process," Clemson University, MSc. Thesis, May 2018.
[7] Alan Liao, "射出成型條件的預估與優化技巧," 科盛科技, Moldex3D, 發行文件 (2015年4月).
[8] 陳夏宗等, "應用高分子 PvT特性的數據及實用方法以控制產品品質之研究," 中原大學,中國機械工程學會第三十五屆全國學術研討會論文集,論文編號#0204, (2018).
[9] 東碩塑料.(2017). High Flow ABS POLYLAC® PA-756.Available: http://www.tpv123.com/ABSsuliao/qimeiPOLYLAC_ABS_PA_756_gaoliudongABS_PA_756_taiwanqimeiABS_PA_756.html
[10] 天星料管工業, PLASTIS PLUS塑膠知識家2019年10月號.Available: http://www.ten-star.com.tw/tw/news_i_N0031.html
[11] 賴峯民等編著, "無電鍍層技術應用於塑膠工業元件的表面機械性質之探討," Journal of Science and Engineering Technology, Vol. 7, No. 4, pp. 19-34 (2011)
[12] 洪敏雄,王木琴,許志雄,蔡明雄,呂英治,方冠榮,盧陽明編著, "工程材料科學," ed:全華圖書股份有限公司, pp.1.1-1.6, 2009年1月.
[13] LUNG CHEN PLASTICS, "塑膠材質大補帖:塑膠ABS," (2019).Available: http://www.lcpf.com.tw
[14] 李建艎,楊久盈, "Introspection on Account of Climate Change and Food Shortage," 綠能及綠色化學電子月刊 第七期, pp.1-16(2011年1月).
[15] 張傳賢,火金三編著, "Acrylonitrile-Butadiene Rubber," ed:中國石化出版社, pp.1-61(2010).
[16] 國喬石化.(2015).ABS製造方法.Available:
https://www.gppc.com.tw/gppc/product-5.asp
[17] "Standard Test Method for Tensile Properties of Plastics," Annual Book of ASTM Standards, ASTM D638-10.
[18] 吳有鎰, "以時序閥澆口及 CAE 技術探討縫合線強度之研究," 國立高雄應用科技大學, 碩士論文, 民國98年.
[19] 台中精機股份有限公司, Available: http://www.or.com.tw.
[20] 科盛科技.(2020)Moldex3D R17, Available :https://www.moldex3d.com/ch/
[21] 晏邦電機工業, 烘料機, Available:
https://www.yannbang.com/hopper-dryer-tw.
[22] 潤輝科技有限公司, 模溫控制機, Available:
http://www.a1-max.com.tw/t/pro_ao.htm#spec.
[23] 弘達儀器股份有限公司.(2019).萬能材料試驗機. Available: http://www.hungta.com/tw/about.html.
[24] 林李旺, "突破品質水準-實驗設計與田口方法之實務應用," 初版 , 新北市, ed:全華圖書股份有限公司, pp. 260-323. , 2013年06月.
[25] 葉怡成, "實驗設計法-製程與產品最佳化," ed: 五南圖書出版股份有限公司, pp.9.1-9.18(2001年6月).
[26] 昊青股份有限公司SFI (Scientific Formosa, Inc).(2021).Minitab. Available: https://www.sciformosa.com.tw/products/minitab
[27] 葉怡成, "實驗設計法-製程與產品最佳化," ed: 五南圖書出版股份有限公司, pp.2.20-2.25, (2001年6月)
[28] 唐麗英, 王春和著"從範例學MINITAB統計分析與應用," ed: 博碩文化股份有限公司,pp.7.2-7.7(2016年11月)
[29] B. Ozcelik, "Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding," International Communications in Heat and Mass Transfer 37, pp. 1359-1365, 2010.
[30] R. Zuraimi, "Tensile strength analysis of high density polyethylene for injection moulded parts," Journal of Advanced Manufacturing Technology, pp. 151-164, 2017.
[31] J. S, Dick , "Rubber technology : Compounding and testing for performance," ed: 化學工業出版社,pp.43-44(2004).
[32] 蔡穎玫、葉羽馨、王茂齡, "射出成型專題報導," 科學發現期刊 第559期, pp.42-51,(2019年7月).
[33] 鄔智傑, "模具內旋轉機構對射出成型之結合線強度的影響," 國立交通大學, 碩士論文, 民國101年.
[34] R. Su et al., "Effect of melt temperature on the phase morphology, thermal behavior and mechanical properties of injection-molded PP/LLDPE blends", Chinese Journal of Polymer Science 28, pp. 249-255, 2010. |