參考文獻 |
1. L. F. Johnson, K. A. Ingersoll and J. V. Dalton, “Planarizing of phosphosilicate glass films on patterned Si wafers”, J. Vac. Sci. Technol., B1, (Apr.-Jun.1983).
2. A. C. Adams and C. D. Capio, “Planarization of phosphorous-doped silicon dioxide”, J. Electrochem. Soc., 128, 423 (1981).
3. L. K. White, “Planarization properties of resistant polyimide coatings”, J. Electrochem. Soc., 130, 1543 (1983).
4. L. Debruin and J. M. F. G. Van Laarhoven, “Advanced multiple-step resist etchback planarization”, in Proc. IEEE V-MIC Conf., 404 (1988).
5. R. H. Wilson and P. A. Piacente, “Effect of circuit structure on Planarization resist thickness”, J. Electrochem. Soc. 133, 981 (1986).
6. G. C. Eiden, J. A. Hughes and P. K. Boyer, “Geometry independent deep trench etching refill and planarization for isolation of merged bipolar-CMOS devices”, j. J. Electrochem. Soc. Ext. Abstract, 84, 7 (Oct. 1984).
7. A. Schiltz and M. Pons, “Two-layer planarization process”, J. Electrochem. Soc., 133, 178 (1986).
8. A. N. Saxena and D. Pramanik, “Planarization techniques for multilevel metallization”, Solid - State technol., 29, 95 (1986).
9. D. B. Tuckerman and A. H. Weiberg, “Planarization of gold and aluminum thin films using a pulsed laser”, Solid - State technol., 29, 129 (1986).
10. S. K. Gupta and R. I. Chin, “Characterisation of spin-on-glass films as a planarizing dielectric”, in Proc. ACS Symp., 22, 295 (1986).
11. A. Schiltz, “Advantages of using spin-on-glass layer in intermediate dielectric planarization”, in Microcircuit Eng. Conf. Proc., 5, 413 (1986).
12. L. B. Rothman, “Process for forming passivated metal interconnection system with a planar surface”, J. Electrochem. Soc., 130, 1131 (1983).
13. H. Fritzsche et al., “Etching of tapered via holes in sandwiched dielectric interlayer for multilevel metallization”, in Proc. IEEE VMIC Conf., p. 253, 1985.
14. E. R. Sirkin and I. A. Blech, “A method of forming contacts between two conducting layers separated by a dielectric”, J. Electrochem. Soc., 131, 123 (1984).
15. P. Sanseau, A. Schiltz, G. Rabilloud and L. Verdet, “Improve lift-off pillar fabrication technique using a polyphenylquinozaline polymer”, in Proc. Electrochem. Soc., 17, 170 (1988).
16. W. L. Patrick, W. L. Guthrie, C. L. Standley and P. M. Schiable, “Application of chemical mechanical polishing to fabrication of VLSI circuit interconnections”, J. Electrochem. Soc., 138, 1778 (1991).
17. I. Ali, R. Sudipto and R. Shinn, “Chemical polishing of interlayer dielectric”, Solid State Technology, 63 (Qct. 1994).
18. T. Izumitani, “Polishing, lapping and diamond grinding of optical glasses”, Material Science and Technology, Vol. 17, Glass Π, ed. By M. Tomozawa and R. H. Doremus, Academic Press, New York, 115 (1979).
19. T. Izumitani, “Polishing mechanism of optical glasses”, Glass Technology, 12, 131 (1971).
20. F. W. Preston, “The theory and design of plate glass polishing machines”, J. Soc. Glass Technology, 11, 214 (1927).
21. S. R. Runnels and L. M. Eyman, “Tribology analysis of chemical-mechanical polishing”, J. Electrochem. Soc., 141, 1698 (1994).
22. S. R. Runnels, “Feature-Scale fluid-based erosion modeling for chemical mechanical polishing”, J. Electrochem. Soc., 141, 1900 (1994).
23. F. Zhang and A. Busnaina, “The Role of Particle Adhesion and Surface Deformation in Chemical Mechanical Polishing Processes”, Electrochemical and Solid-State Letters, 1, 184 (1998).
24. Q. Luo, S. Ramarajan and S. V. Babu, “Modification of the Preston equation for the chemical-mechanical polishing of copper”, Thin Solid Films, 335, 160 (1998).
25. 蔡明義 蔡志成 蔡明蒔 “應用田口法於晶片化學機械平坦化製程參數之實驗探討” 中國機械工程學會第十六屆全國學術研討會 第五冊, 541 (中華民國八十八年十二月).
26. B. Zhao and F. G. Shi, “Chemical Mechanical Polishing : Threshold Pressure and Mechanism”, Electrochemical and Solid-State Letters, 2, 145 (1999).
27. W. T. Tseng, J. H. Chin, and L. C. Kang, “Comparative study on the roles of velocity in the material removal rate during chemical mechanical polishing”, J. Electrochem. Soc., 146, 1952 (1999).
28. C. Y. Chen, C. C. Yu, S. H. Shen, and M. Ho, “Operational Aspect of Chemical Mechanical Polishing Polish Pad Profile Optimization”, J. Electrochem. Soc., 147, 3922 (2000).
29. Y. Hayashi, M. Sakurai, T. Nakajima and K. Hayashi, “Ammonium-salt-added silica slurry for the chemical mechanical polishing of the interlayer dielectric film planarization in ULSIS”, Jpn. J. Appl. Phys., 34, 1037 (1995).
30. C. Millot, “Geology of clay”, Springer-Uerrlag, New York, 55 (1970).
31. A. Kaller, Mschr. Feinmech. Opt., 79, 135 (1962).
32. L. M. Cook, “Chemical Processes in Glass Polishing”, J. Non-cryst. Solids, 120, 152 (1990).
33. F. B. Kaufman, D.B. Thompson, R. E. J. Broadie, M. A. Jaso, W. L. Guthrie, D. J. Pearson and M. B. Small, “Chemical—mechanical polishing for fabricating patterned W metal features as chip interconnects”, J. Electrochem. Soc., 138, 3460 (1991).
34. M. Tomozawa, K. Yang, H. Liang, S. Ganeshkumar, W. Fortino, “Effect of Slurry Viscosity Modification on Oxide and Tungsten CMP”, Wear, 214, 10 (1998).
35. H. W. Chiou, L. J. Chen and H. C. Chen, “On monitoring CMP removal rate by in-situ temperature measurements”, Proc. of VIMIC Specialty Conference on CMP Planarization, 131 (1997).
36. H. W. Chiou and L. J. Chen, “Proportional -integral-derivative (PID) run to run control of CMP removal rate”, Proc. of VIMIC Specialty Conference on CMP Planarization, 375 (1997).
37. S. Sivaram, H. Bath, E. Lee, R. Leggett, and R. Tolles, “Measurement and Modeling of Pattern Sensitivity during Chemical Mechanical Polishing of Interlevel Dielectrics”, Technical Report, SEMATECH, Austin, TX. (1992).
38. S. R. runnels and T. Olavson, ”Optimizing wafer polishing through phenomenological modeling”, J. Electrochem. Soc., 142, 2032 (1995).
39. J. Warnock, “Two-dimensional process model for chemimechanical polish planarization”, J. Electrochem. Soc., 138, 2398 (1991).
40. C. W. Liu, B. T. Dai and C. F. Yeh, “Characterization of the chemical-mechanical polishing process based on Nanoindentation measurement of dielectric film”, J. Electrochem. Soc., 142, 3098 (1995).
41. D. Wang, J. Lee, K. Holland, T. Bibby, S. Beaudoin, and T. Cale, “Von Mises Stress in Chemical Mechanical Polishing Processes”, J. Electrochem. Soc., 144, 1121 (1997).
42. M. N. Fu and F. C. Chou, “Flow simulation for chemical mechanical planarization”, Jpn. J. Appl. Phys., 38, 4709 (1999).
43. S. R. Runnels, “Advances in physically based erosion simulators for CMP”, J. Electronic Materials, 25, 1574 (1996).
44. A. Modak, P. Monteith and N. Parekh, “Components of within-wafer nonuniformity in a dielectric CMP process.”, Proc. Of CMP-MIC Conference, 169 (1997).
45. T. F. A. Bibby, R. Harwood, D. Schey and K. McKinley, “Cartesian coordinate maps for chemical mechanical planarization uniformity characterization.”, Thin Solid Film, 308-309, 512 (1997).
46. D. G. Thakurta, C. L. Borst, D. W. Schwendeman, R. J. Gutmann, and W. N. Gill, “Pad porosity, compressibility and slurry delivery effects in chemical-mechanical planarization : modeling and experiments”, Thin Solid Films, 336, 181 (2000).
47. J. Coppeta, C. Rogers, A. Philipossian and F. B. Kaufman, “A technique for measuring slurry flow dynamics during chemical mechanical polishing”, Proc. of Material Research Society, 447, 95 (1996).
48. J. Coppeta, C. Rogers, A. Philipossian and F. B. Kaufman, “Characterizing slurry flow during CMP using laser induced fluorescence”, Proc. of CMP-MIC Conference, 307 (1997).
49. J. Coppeta, C. Rogers, A. Philipossian, F. Kaufman and L. Racz, “Pad effects on slurry transport beneath a wafer during polishing”, Third International Chemical Mechanical Polish Planarization for ULSI Multilevel Interconnection Conference, Santa Clara, CA, USA, 36 (1998).
50. J. Coppeta, C. Rogers, L. Racz, A. Philipossian and F. B. Kaufman, “Investigating slurry transport beneath a wafer during chemical mechanical polishing processes”, J. Electrochem. Soc., 147, 1903 (2000).
51. Z. Stavreva, D. Zeidler, M. Plotner, and K. Drescher, “Characteristics in chemical mechanical polishing of copper: comparison of polishing pads”, Appl. Surf. Sci., 108, 39 (1997).
52. S. Sundararajan, D. G. Thakurta, D. W. Schwendeman, S. P. Murarka and W. N. Gill, “Two-domensional wafer-scale chemical mechanical planarization models based on lubrication theory and mass transport”, J. Electrochem. Soc., 146, 761 (1999).
53. Z. Stavreva , D. Zeidler, M. Plotner, and K. Drescher, “Chemical mechanical polishing of copper for multilevel metallization”, Appl. Surf. Sci., 91, 192 (1995).
54. F. C. Chou, M. N. Fu and M. W. Wang, “A general optimization for slurry inject during chemical mechanical planarization”, J. Electrochem. Soc., 147, 3873 (2000).
55. D. Bullen, A. Scarfo, A. Koch, D. P. Bramono, J. Coppeta, and L. Racz, “In Situ Technique for Dynamic Fluid Film Pressure Measurement during Chemical Mechanical Polishing”, J. Electrochem. Soc., 147, 2741 (2000). |