17-4 PH不銹鋼高溫疲勞裂縫成長行為研究

以作者查詢圖書館館藏

、以作者查詢臺灣博碩士

、以作者查詢全國書目

、勘誤回報

、線上人數：28

、訪客IP：3.138.69.101

姓名

許貴彰(Kuei-Chang Hsu) 查詢紙本館藏

畢業系所

機械工程學系

論文名稱

17-4 PH不銹鋼高溫疲勞裂縫成長行為研究
(High-Temperature Fatigue Crack Growth Behavior of 17-4 PH Stainless Steel)

相關論文

★ 晶圓針測參數實驗與模擬分析	★ 車銑複合加工機床面結構最佳化設計
★ 精密空調冷凝器軸流風扇葉片結構分析	★ 第四代雙倍資料率同步動態隨機存取記憶體連接器應力與最佳化分析
★ PCB電性測試針盤最佳鑽孔加工條件分析	★ 鋰-鋁基及鋰-氮基複合儲氫材料之製程開發及研究
★ 合金元素(錳與鋁)與球磨處理對Mg2Ni型儲氫合金放電容量與循環壽命之影響	★ 鍶改良劑、旋壓成型及熱處理對A356鋁合金磨耗腐蝕性質之影響
★ 核電廠元件疲勞壽命模擬分析	★ 可撓式OLED封裝薄膜和ITO薄膜彎曲行為分析
★ MOCVD玻璃承載盤溫度場分析	★ 不同環境下之沃斯回火球墨鑄鐵疲勞裂縫成長行為
★ 不同環境下之Custom 450不銹鋼腐蝕疲勞性質研究	★ AISI 347不銹鋼腐蝕疲勞行為
★ 環境因素對沃斯回火球墨鑄鐵高週疲勞之影響	★ AISI 347不銹鋼在不同應力比及頻率下之腐蝕疲勞行為

檔案

[Endnote RIS 格式]

[Bibtex 格式]

[相關文章]

[文章引用]

[完整記錄]

[館藏目錄]

[檢視]

[下載]

本電子論文使用權限為同意立即開放。
已達開放權限電子全文僅授權使用者為學術研究之目的，進行個人非營利性質之檢索、閱讀、列印。
請遵守中華民國著作權法之相關規定，切勿任意重製、散佈、改作、轉貼、播送，以免觸法。

摘要(中)

本研究之宗旨在探討經三種時效熱處理（固溶處理Condition A、頂時效處理H900及過時效處理H1150）之17-4 PH不銹鋼其高溫疲勞裂縫成長行為。實驗結果顯示，在荷重比為0.1及負荷頻率2 Hz的條件下，於室溫至500oC之間，H1150的疲勞裂縫成長速率會隨著溫度的上升而增加，但Condition A與H900於500oC之疲勞裂縫成長速率反而比較低溫度之值為低。在300和400oC，比較三種熱處理之疲勞裂縫成長速率，均為H900最高，Condition A次之，H1150最低。在500oC，三種熱處理之疲勞裂縫成長速率則非常接近，Condition A及H900的疲勞裂縫成長速率於500oC時的異常變化，主要由即時之析出粒子粗化效應所造成。
在負荷頻率對高溫疲勞裂縫成長行為的影響方面，在500oC，三種熱處理在各頻率（0.002 ~ 2 Hz）下都有相近的疲勞裂縫成長速率，且在頻率低於2 Hz時其疲勞裂縫成長速率會隨頻率的下降而上升。此頻率效應是由裂縫尖端氧化與循環負載的加乘作用所造成，頻率越低，則氧化的加乘效果越明顯。在400oC，雖然三種熱處理的疲勞裂縫成長速率並不相同，但都會在較高頻率時隨頻率下降而上升，而在較低頻率時不受頻率效應影響。此三種熱處理於400oC時，呈現不同於一般材料的頻率效應，則是由動態應變時效（DSA）所造成。另外，在各個頻率下，H1150的疲勞裂縫成長速率會隨著溫度的上升而增加，而Condition A與H900於500oC之疲勞裂縫成長速率會較400oC之值為低，此現象如前述是由即時之析出粒子粗化效應所造成。
在荷重比對高溫疲勞裂縫成長行為的影響方面，在400oC、2 Hz的條件下，三種熱處理的疲勞裂縫成長速率在低DeltaK區域皆會隨荷重比的增加而上升，且在高DeltaK區域不受荷重比效應影響。唯H900在高DeltaK區域時其疲勞裂縫成長速率仍會隨荷重比的增加而上升。在500oC，H1150的疲勞裂縫成長速率在較低荷重比時會隨荷重比的上升而增加，但在較高荷重比時不受荷重比效應所影響。若以統合分析方法（Unified Approach）對三種熱處理之17-4 PH不銹鋼進行分析，可發現其疲勞裂縫成長速率隨荷重比的變化，純粹是因材料之裂縫成長機制需同時滿足兩個裂縫成長門檻值所反應出來的結果。三種熱處理在不同溫度下都有共通的裂縫成長機制，並與一般疲勞裂縫成長之塑性鈍化成長機制（plastic blunting process）相似。唯Condition A和H900在400oC、高荷重比的條件下，其疲勞裂縫成長亦會受結晶面破裂（crystallographic-faceted）機制所影響。此外，各種熱處理於不同荷重比下的疲勞裂縫成長速率可用一荷重比整合參數（M*DeltaK）加以整合，有相當好的效果。使用此整合參數配合最佳擬合曲線，可以用來預測各種條件下之17-4 PH不銹鋼在任意荷重比下的疲勞裂縫成長速率。

摘要(英)

High-temperature fatigue crack growth (FCG) behavior was investigated for 17-4 PH stainless steels in three heat-treated conditions, namely unaged “Condition A,” peak-aged “Condition H900,” and overaged “Condition H1150.” Baseline FCG behavior was studied at a load ratio of 0.1, a frequency of 2 Hz and temperatures ranging from 300 to 500oC. The fatigue crack growth rates (FCGRs) of Condition H1150 were increased with an increase in temperature from 300 to 500oC. However, for Conditions A and H900 tested at 500oC, the FCGRs were lower than the lower-temperature ones. At 300 and 400oC, H1150 and H900 generally showed the lowest and highest FCGRs, respectively, with Condition A demonstrating behavior between the two. At 500oC, the FCGR curves for all heat-treated conditions merged together. The anomalous FCG behavior of 17-4 PH stainless steels at 500oC was mainly caused by an in-situ overaging and precipitate-coarsening effect during test.
The influence of frequency on FCG behavior was investigated at 400 and 500oC with a load ratio of 0.1 and frequencies ranging from 0.002 to 20 Hz. At 500oC, all heat-treated conditions exhibited similar FCG behavior in which no frequency effect was observed at frequencies higher than 2 Hz and the FCGRs increased with decreasing frequency below 2 Hz. The increase in FCGR at a lower frequency at 500oC was thought to be caused by a time-dependent, oxidation-assisted cracking mechanism. At 400oC, for a given heat-treated condition, the FCGRs increased with decreasing frequency at higher frequencies and leveled off at lower frequencies. Such an anomalous FCG behavior was attributable to a dynamic strain aging (DSA) effect. At a given frequency, when the temperature was increased from 400 to 500oC, the FCGR increased in Condition H1150, but decreased in Conditions A and H900 due to the aforementioned in-situ overaging and precipitate-coarsening effect during test.
The load ratio effect on FCG behavior was investigated at 400 and 500oC with a frequency of 2 Hz and load ratios ranging from 0.1 to 0.7. The FCGRs increased with load ratio at lower

關鍵字(中)

★ 17-4 PH不銹鋼
★ 高溫
★ 疲勞裂縫成長
★ 頻率
★ 荷重比

關鍵字(英)

★ high temperature
★ 17-4 PH stainless steel
★ fatigue crack growth
★ load ratio
★ frequency

論文目次

LIST OF TABLES VIII
LIST OF FIGURES.IX
1. INTRODUCTION 1
1.1 Literature Review 2
1.2 Purpose and Scope 7
2. MATERIAL AND EXPERIMENTAL PROCEDURES 9
2.1 Material and Specimen Geometry 9
2.2 Heat Treatments 9
2.3 Testing Procedure 10
3. RESULTS AND DISCUSSION 13
3.1 Baseline Fatigue Crack Growth Behavior 13
3.1.1 Effects of Temperature on Fatigue Crack Growth at 2 Hz 13
3.1.2 Effects of Heat-Treatment on Fatigue Crack Growth at 2 Hz 15
3.2 Effects of Frequency on Fatigue Crack Growth Behavior 16
3.2.1 Effects of Frequency on Fatigue Crack Growth Rates 16
3.2.2 Effects of Heat-Treatment on Fatigue Crack Growth at Various Frequencies 23
3.2.3 Effects of Temperature on Fatigue Crack Growth at Various Frequencies 26
3.3 Effects of Load Ratio on Fatigue Crack Growth Behavior 27
3.3.1 Effects of Load Ratio on Fatigue Crack Growth Rates 27
3.3.2 Models of Fatigue Crack Growth under Different Load Ratios 35
4. CONCLUSIONS 43
REFERENCES 45
TABLES 52
FIGURES 55
PUBLICATIONS 110

參考文獻

1. W. F. Smith, Structure and Properties of Engineering Alloys, 2nd Ed., McGraw-Hill, Inc., New York, USA, 1993.
2. U. K. Viswanathan, S. Banerjee and R. Krishnan, “Effect of Aging on the Microstructure of 17-4 PH Stainless Steel,” Materials Science and Engineering A, Vol. A104, 1988, pp. 181-189.
3. H. J. Rack and D. Kalish, “The Strength, Fracture Toughness, and Low Cycle Fatigue Behavior of 17-4 PH Stainless Steel,” Metallurgical Transactions, Vol. 5, 1974, pp. 1595-1605.
4. F. B. Pickering, “Physical Metallurgy of Stainless Steel Developments,” International Metals Reviews, Vol. 21, 1976, pp. 227-268.
5. R. D. K. Misra, G. Y. Prasad, T. V. Balasubramanian, and P. R. Rao, “Effect of Phosphorus Segregation on Impact Toughness Variation in 17-4 PH Precipitation Hardened Stainless Steel,” Scripta Metallurgica, Vol. 20, 1986, pp. 713-716.
6. R. D. K. Misra, G. Y. Prasad, T. V. Balasubramanian, and P. R. Rao, “On Variation of Impact Toughness in 17-4 PH Precipitation Hardened Stainless Steel,” Scripta Metallurgica, Vol. 21, 1987, pp. 1067-1070.
7. “Carpenter Precipitation Hardening Stainless Steels,” Manufacturer’s Product Bulletin, Carpenter Technology Co., PA, 1986.
8. K. C. Antony, “Aging Reactions in Precipitation Hardenable Stainless Steel,” Journal of Metals, Vol. 15, 1963, pp. 922-927.
9. U. K. Viswanathan, P. K. K. Nayar and R. Krishnan, “Kinetics of Precipitation in 17-4 PH Stainless Steel,” Materials Science and Technology, Vol. 5, 1989, pp. 346-349.
10. X. Zang, “Microstructural Study of 17-4 PH Steel after Aging Treatment,” Transactions of Metal Heat Treatment, Vol. 12, 1991, pp. 23-29. (in Chinese)
11. G. Huang, “Study on the Structure and Performance of 17-4 PH Stainless Steel,” Iron and Steel, Vol. 33, 1998, pp. 44-46. (in Chinese)
12. M. U. Islam, G. Campbell and R. Hsu, “Fatigue and Tensile Properties of EB Welded 17-4 PH Steel,” Welding Journal, Vol. 68, 1989, pp. 45-50.
13. S. Isogawa, H. Yoshida, Y. Hosoi, and Y. Tozawa, “Improvement of the Forgeability of 17-4 PH Precipitation Hardening Stainless Steel by Ausforming,” Journal of Materials Processing Technology, Vol. 74, 1998, pp. 298-306.
14. Y. Tan, J. Wang and S. Wang, “Phase Transformation of 17-4 PH Steel in Aging Processes,” Transactions of Metal Heat Treatment, Vol. 14, 1993, pp. 1-7.
15. C. N. Hsiao, C. S. Chiou and J. R. Yang, “Aging Reaction in a 17-4 PH Stainless Steel,” Materials Chemistry and Physics, Vol. 74, 2002, pp. 134-142.
16. M. Murayama, Y. Katayama and K. Hono, “Microstructural Evolution in a 17-4 PH Stainless Steel after Aging at 400oC,” Metallurgical and Materials Transactions A, Vol. 30A, 1999, pp. 345-353.
17. J.-H. Wu and C.-K. Lin, “Tensile and Fatigue Properties of 17-4 PH Stainless Steel at High Temperatures,” Metallurgical and Materials Transactions A, Vol. 33A, 2002, pp. 1715-1724.
18. J.-H. Wu and C.-K. Lin, “Influence of High Temperature Exposure on the Mechanical Behavior and Microstructure of 17-4 PH Stainless Steel,” Journal of Materials Science, Vol. 38, 2003, pp. 965-971.
19. J.-H. Wu and C.-K. Lin, “Influence of Frequency on High-Temperature Fatigue Behavior of 17-4 PH Stainless Steels,” Materials Transactions, JIM, Vol. 44, 2003, pp. 713-721.
20. J.-H Wu and C.-K. Lin, “Effect of Strain Rate on High-Temperature Low-Cycle Fatigue of 17-4 PH Stainless Steels,” Materials Science and Engineering A, Vol. A390, 2005, pp. 291-298.
21. Metals Handbook, 10th Ed., Vol. 1, ASM International, Materials Park, OH, 1990, pp. 930-949.
22. K. C. Russel and L. M. Brown, “A Dispersion Strengthening Model Based on Differing Elastic Moduli Applied to the Iron-Copper System,” Acta Metallurgica, Vol. 20, 1972, pp. 969-974.
23. E. Hornbogen, “The Role of Strain Energy during Precipitation of Copper and Gold from Alpha Iron,” Acta Metallurgica, Vol. 10, 1962, pp. 525-533.
24. A. Youle and B. Ralph, “A study of the Precipitation of Copper from

指導教授

林志光(Chih-Kuang Lin)

審核日期

2007-7-6

推文